Please use this identifier to cite or link to this item:
https://idr.nitk.ac.in/jspui/handle/123456789/14576
Title: | Experimental Investigation of 3d Printed Syntactic Foam Composites |
Authors: | Patil, Balu. |
Supervisors: | Doddamani, Mrityunjay |
Keywords: | Department of Mechanical Engineering;Syntactic foam filament;3D printing;FFF;High density polyethylene;Fly ash cenosphere;Crystallinity;CTE;Mechanical properties |
Issue Date: | 2019 |
Publisher: | National Institute of Technology Karnataka, Surathkal |
Abstract: | Polymer matrix composites can reduce the structural weight and result in improved fuel efficiency and performance in transportation applications. Thermoplastic matrix composites have been used for semi-structural and engineering applications. In addition to the ease of fabrication using a wide range of forming processes, thermoplastic polymers are recyclable, which is the strong driving force for their current and future applications. Rapid production of high quality components is the key to cost reduction in industrial applications. The present work is the first attempt of manufacturing syntactic foams, hollow particle filled lightweight composites using thermoplastic based fused filament fabrication /fused deposition modeling (FFF/FDM) 3D printing process. High Density Polyethylene (HDPE) is used as the matrix material and fly ash cenospheres as the filler. Development of syntactic foams with cenospheres serves dual purpose of beneficial utilization of industrial waste fly ash and reduction in the component cost. Hollow fly ash cenospheres are blended with HDPE to form cenosphere/HDPE blend and is extruded to filament form and finally fed through 3D printer for printing ecofriendly lightweight syntactic foams. Prior to filament development, thermal degradation, melt flow index (MFI) and rheological properties of cenosphere/HDPE blend are studied. MFI decreased by 39.29, 60.54 and 70.51% with increasing cenospheres content of 20, 40 and 60 vol. % respectively. Rheology study of cenosphere/HDPE blend revealed complex viscosities values are maximum at a lower frequency but decreases with an increasing frequency indicating shear thinning behaviour. Both storage and loss modulus showed an increasing trend with filler content and frequency. Single screw extruder parameters are optimized to develop ecofriendly syntactic foam filament with minimum cenosphere fracture and to obtain homogeneous mixing of constituents. The optimized parameters are used for manufacturing syntactic foams filament with 20, 40 and 60 vol.% cenosphere in HDPE matrix. Further, recycling potential of foam filament is also studied. Density of H40 (HDPE with 40 vol.% ofcenospheres) foams increased in up to two extrusion passes (2X) due to cenosphere breakage and porosity consolidation. Tensile properties of developed filaments are carried out to assess its viability into 3D printer. Tensile modulus and yield strength of neat HDPE filaments increased with each extrusion pass. Specific modulus of 3D printed H40-2X and 3X are 1.6 and 2.6 times higher than the respective filaments, however, fracture strain decreases by up to 40%. For first time extruded (1X) filament with addition of cenosphere density reduces due to intact cenosphere and void formation during extrusion, making it a 3 phase foam material. The void content and weight saving potential increases with increase in filler content and their values are higher for 3D prints than respective filament. Higher filler loading increases filament modulus by 7.72-12.79% as compared to HDPE. Among the foam filaments, H20 composition registered the highest ultimate strength (10.30 MPa) and strain at break (26.20%). Differential scanning calorimeter and X-ray diffraction analysis of neat HDPE and foam filaments crystallinity is used to assess the parametric optimization of 3D printing process. It is observed that addition of cenosphere reduced crystallinity of HDPE. HDPE and foam filaments exhibit lower crystallinity as compared to respective printed material. Coefficient of thermal expansion (CTE) of 3D printed HDPE and its foam is studied to understand warping and shrinkage phenomenon occurring during printing. It is observed that filler addition in HDPE matrix reduces CTE remarkably. Warpage of the specimen is reduced with filler content and print quality is further improvised by optimizing printer speed, layer thickness, print temperature and cooling conditions. Tensile tests are carried out on filaments and printed samples. Cenospheres addition resulted in improved tensile modulus and decreased filament strength. Tensile modulus of printed foams increases with filler content. 3D printed HDPE and foams modulus is better than respective feedstock material (filament). Tensile properties of 3D printed HDPE and foams are compared with injection molded samples. 3D printed HDPE registered higher tensile modulus and fracture strength compared to injection molding. Flexural test is conducted on 3D printed sample in two configurations (topand bottom face of print subjected to the load). Results obtained from both configurations reveals that second configuration has shown better flexural modulus and strength. Neat HDPE print did not show any fracture below 10% strain. Flexural modulus increases with cenosphere content. Highest modulus is exhibited by H60 which is 1.56 times better than neat HDPE print. Raster gaps in 3D prints lowers flexural modulus and strength as compared to fully dense injection molded sample. Quasi-static and regular strain rate compressive response is investigated on prints. Compressive behaviour of 3D printed foams follow similar trend in quasi-static and regular compressive mode as reported in fully dense injection molded two-phase foams. Modulus of neat HDPE is higher for all strain rates as compared to foams. Yield strength shows an increasing trend with strain rate. Highest specific compressive modulus and yield strength is observed for H60 and H20 respectively at 0.1 s-1 among foams. Further, HDPE matrix syntactic foam prints are characterized for their viscoelastic properties by dynamic mechanical analysis. Tests are conducted over 30-125°C temperatures. Storage and loss modulus increase with increasing volume fraction of cenospheres, with a slight difference between HDPE, H20 and H40 vol.%, at all temperatures. Storage modulus decreased with increasing temperature for neat HDPE and foam prints. Storage and loss modulus decrease with increasing temperature in the range of 30-125°C, while Tan δ increases. Structureproperty correlations of all the investigated properties are presented with the help of exhaustive SEM images to understand underlying mechanisms. Property maps for selected test conditions are presented for comparative analysis between FFF/FDM based 3D printing of eco-friendly lightweight syntactic foam prints and other processing routes used for thermoplastics. This work is an effort towards making wide material choices availability for FFF based 3D printing industries. Finally, the potential for using the optimized parameters of 3D printing is demonstrated by printing several industrial components as a deliverable of of this work. |
URI: | http://idr.nitk.ac.in/jspui/handle/123456789/14576 |
Appears in Collections: | 1. Ph.D Theses |
Files in This Item:
File | Description | Size | Format | |
---|---|---|---|---|
165001ME16F01.pdf | 5.87 MB | Adobe PDF | View/Open |
Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.