Browsing by Author Herbert, M.A.

Jump to: 0-9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
or enter first few letters:  
Showing results 1 to 20 of 21  next >
Issue DateTitleAuthor(s)Supervisor(s)
2019Active Upper Arm Exoskeleton - Design and Kinematic AnalysisSantra, P.; Mukhopadhyay, A.; Debnath, B.; Herbert, M.A.; Bhaumik, S.-
2019Assessment of influence of process parameters on properties of friction stir welded Al-Ce-Si-Mg aluminium alloyD'Souza, A.D.; Rao, S.S.; Herbert, M.A.-
2014Correlation of Tribological Properties with Microstructure and Mechanical Properties of Graphite Cast Irons Centrifugally Cast for Engine LinerDesai, Gowda, H.S.; Mukunda, P.G.; Herbert, M.A.-
2018Development of novel cutting tool with a micro-hole pattern on PCD insert in machining of titanium alloyRao, C.M.; Rao, S.S.; Herbert, M.A.-
2013Effect of centrifugal and gravity casting technique over metallographic and mechanical properties of spheroidal graphite ironDesai, Gowda, H.S.; Mukunda, P.G.; Herbert, M.A.-
2019Effect of low temperature annealing on the properties of nano Ni-Ti alloysMukunda, S.; Vinyas, M.; Narendranath, S.; Herbert, M.A.-
2016Effect of low temperature annealing on the wear properties of NITINOLMukunda, S.; Naths, N.; Herbert, M.A.; Mukunda, P.G.-
2011Effect of mushy state rolling on age-hardening and tensile behavior of Al-4.5Cu alloy and in situ Al-4.5Cu-5TiB2 compositeSiddhalingeshwar, I.G.; Herbert, M.A.; Chakraborty, M.; Mitra, R.-
2019An Efficient Approach to Optimize Wear Behavior of Cryogenic Milling Process of SS316 Using Regression Analysis and Particle Swarm TechniquesKarthik, Rao, M.C.; Malghan, R.L.; ArunKumar, S.; Rao, S.S.; Herbert, M.A.-
2020An Experimental and Numerical Approach to Study the Performance of Modified Perforated Cutting Tools on Machining of Ti 6Al 4V AlloyRao, C.M.; Rao, S.S.; Herbert, M.A.-
2017Experimental study on linear displacement measurement sensor using RGB color variation technique with PID controllerMurthy, A.; Rao, S.S.; Herbert, M.A.; Navin, Karanth, P.-
2018Influence of modified cutting inserts in machining of Ti-6Al-4V alloy using PCD insertRao, C.M.; Rao, S.S.; Herbert, M.A.-
2019Investigation of errors in microcontroller interface circuit for mutual inductance sensorAnarghya, A.; Rao, S.S.; Herbert, M.A.; Navin, Karanth, P.; Rao, N.-
2016Investigation on microstructure and mechanical properties of Friction Stir Welded AA6061-4.5Cu-10SiC compositeHerbert, M.A.; Shettigar, A.K.; Nigalye, A.V.; Rao, S.S.-
2018Machining Parameters Optimization of AA6061 Using Response Surface Methodology and Particle Swarm OptimizationLmalghan, R.; Rao, K.; ArunKumar, S.; Rao, S.S.; Herbert, M.A.-
2014Microstructure and hardness of friction stir welded aluminium-copper matrix-based composite reinforced with 10 wt-% SiCpKumar, A.; Veeresh, Nayak, C.; Herbert, M.A.; Rao, S.S.-
2019Microstructure evolution and mechanical properties of friction stir welded AA6061/rutile compositePrabhu, S.R.B.; Shettigar, A.K.; Herbert, M.A.; Rao, S.S.-
2013Preparation and evaluation of mechanical properties of Al-6061 reinforced with graphite and fly ash of seed husk (Honge) particulate metal matrix compositeEdrard, C.; Kapilan, N.; Herbert, M.A.-
2016Soft computing techniques during drilling of bi-directional carbon fiber reinforced compositeShetty, N.; Herbert, M.A.; Shetty, R.; Shetty, D.S.; Vijay, G.S.-
2019Studies on the Effect of Process Parameters in Turning of Ti-6Al-4V Alloy Using TopsisRao, C.M.; Rao, S.S.; Herbert, M.A.-