Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
40 results
Search Results
Item Phase transformation, structural evolution, and mechanical property of nanostructured feal as a result of mechanical alloying(Springer New York LLC barbara.b.bertram@gsk.com, 2009) Rajath Hegde, M.M.R.; Surendranathan, A.O.The objective of the work is to synthesize nanostructured FeAl alloy powder by mechanical alloying (MEA). The work concentrates on the synthesis, characterization, and structural and mechanical properties of the alloy. Nanostructured FeAl intermetallics are prepared directly by MEA in a high-energy ball mill. Milling is performed under toluene solution to avoid contamination from the milling media and atmosphere. Mixtures of elemental Fe and Al are progressively transformed into a partially disordered solid solution with an average composition of Fe-50 at.% Al. Phase transformation, structural changes, morphology, particle size measurement, and chemical composition during MEA are investigated by X ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive x-ray spectroscopy (EDS). Vickers microhardness (VMH) indentation tests are performed on the powders. The XRD and SEM studies reveal the alloying of elemental powders as well as transition to nanostructured alloy; crystallite size of 18 nm is obtained after 28 h of milling. Expansion/contraction in lattice parameter accompanied by reduction in crystallite size occurs during transition to nanostructured alloy. Longer milling introduces ordering in the alloyed powders as proved by the presence of superlattice reflection. Elemental and alloyed phases coexist while hardness increases during MEA. copy2009 Springer Science+Business Media, Inc.Item Phase transformation, structural evolution and mechanical property of nanostructured FeAl as a result of mechanical alloying(2009) Rajath Hegde, M.M.R.; Surendranathan, A.O.Objective of the work was to synthesize nanostructured FeAl alloy powder by mechanical alloying (MEA). The work concentrated on synthesis, characterization, structural and mechanical properties of the alloy. Nanostructured FeAl intermetallics were prepared directly by MEA in a high energy rate ball mill. Milling was performed under toluene solution to avoid contamination from the milling media and atmosphere. Mixtures of elemental Fe and Al were progressively transformed into a partially disordered solid solution with an average composition of Fe-50 at % Al. Phase transformation, structural changes, morphology, particle size measurement and chemical composition during MEA were investigated by X-ray diffraction (XRD), Scanning electron microscopy (SEM) and Energy dispersive X-ray spectroscopy (EDS) respectively. Vickers micro hardness (VMH) indentation tests were performed on the powders. XRD and SEM studies revealed the alloying of elemental powders as well as transition to nanostructured alloy, crystallite size of 18 nm was obtained after 28 hours of milling. Expansion/contraction in lattice parameter accompanied by reduction in crystallite size occurs during transition to nanostructured alloy. Longer milling duration introduces ordering in the alloyed powders as proved by the presence of superlattice reflection. Elemental and alloyed phase coexist while hardness increased during MEA. © 2009 Allerton Press, Inc.Item Enhancement of heat transfer characteristics of transformer oil by addition of aluminium nanoparticles(2011) Rajesh, E.; Prabhu, K.N.A two step approach involving the synthesis of Al nanoparticles by mechanical milling followed by dispersion of the nanoparticles in the base fluid is adopted in the present work to prepare transformer oil based nanofluids. Stainless steel (AISI 304) probes of diameter 15 mm and height 70 mm were used to determine the cooling rate intensities of nanofluids. Heat transfer coefficients were determined using Kobasko's method. A dynamic contact angle analyzer was used to determine the contact angle of the droplet on the substrate. The addition of Al nanoparticles to the base fluid decreases the wettability and improves its heat transfer capability. The vapour phase stage existed for a longer period of time for transformer oil than for Al-transformer oil based nanofluids. The dispersion of nanoparticles in the base fluid is believed to disrupt the vapour blanket stage in the early stage of the cooling process. The peak heat transfer coefficient increases with an increase in the Al nanoparticle content in the oil. The addition of 0.5 vol % nanoparticles enhances the peak heat transfer coefficient by about 70 %. Copyright © 2011 by ASTM International.Item Sound level produced during rock drilling vis-à-vis rock properties(2011) Rajesh Kumar, B.; Vardhan, H.; Govindaraj, M.The process of drilling, in general, always produces sound. Though sound is used as a diagnostic tool in mechanical industry, its application in predicting rock property is not much explored. In this study, an attempt has been made to estimate rock properties such as uniaxial compressive strength, Schmidt rebound number and Young's modulus using sound level produced during rotary drilling. For this purpose, a computer numerical controlled vertical milling centre was used for drilling holes with drill bit diameters ranging from 6 to 20. mm with a shank length of 40. mm. Fourteen different rock types were tested. The study was carried out to develop the empirical relations using multiple regression analysis between sound level produced during drilling and rock properties considering the effects of drill bit diameter, drill bit speed and drill bit penetration rate. The F-test was used to check the validity of the developed models. The measured rock property values and the values calculated from the developed regression model are fairly close, indicating that the developed models could be efficiently used with acceptable accuracy in prediction of rock properties. © 2011 Elsevier B.V.Item Enhancement of heat transfer characteristics of transformer oil by addition of aluminium nanoparticles(ASTM International, 2012) Rajesh, E.; Prabhu, K.N.A two step approach involving the synthesis of Al nanoparticles by mechanical milling followed by dispersion of the nanoparticles in the base fluid is adopted in the present work to prepare transformer oil based nanofluids. Stainless steel (AISI 304) probes of diameter 15 mm and height 70 mm were used to determine the cooling rate intensities of nanofluids. Heat transfer coefficients were determined using Kobasko's method. A dynamic contact angle analyzer was used to determine the contact angle of the droplet on the substrate. The addition of Al nanoparticles to the base fluid decreases the wettability and improves its heat transfer capability. The vapour phase stage existed for a longer period of time for transformer oil than for Al-transformer oil based nanofluids. The dispersion of nanoparticles in the base fluid is believed to disrupt the vapour blanket stage in the early stage of the cooling process. The peak heat transfer coefficient increases with an increase in the Al nanoparticle content in the oil. The addition of 0.5 vol % nanoparticles enhances the peak heat transfer coefficient by about 70%. Copyright © 2011 by ASTM International, 100 Barr Harbor Drive, PO Box C700,.Item Interparticle interactions and lacunarity of mechano-chemically activated fly ash(Elsevier, 2015) Patil, A.G.; Shanmugharaj, A.M.; Anandhan, S.A class F fly ash was subjected to high-energy ball milling-induced mechano-chemical activation aided by a surfactant. The resultant nanostructured fly ash was characterized by various techniques. X-ray fluorescence results showed that the amount of iron oxide was reduced from 4.39% to 2.75% after pre-treatment of fly ash by magnetic separation. Ethyl acetate as the milling medium, a ball to powder ratio of 12:1 and 2wt% of surfactant reduced the average particle size of fly ash to 329nm and led to a specific surface area of 8.73m2/g. The decrease in crystallite size of mechano-chemically activated fly ash was confirmed from a reduction in peak intensity with a broadened amorphous phase by X-ray diffraction studies. X-ray photoelectron spectroscopic characterization illustrated that peak area of major elements (O, Si and Al) increased after milling. Morphological and FTIR studies revealed that the smooth and inert surface of the fly ash was converted to a rough and more reactive one after mechano-chemical activation. The surface modification of fly ash with the surfactant was determined from FTIR spectroscopy. Also, a fractal approach was used to characterize the lacunarity of the agglomerates in the nanostructured fly ash. © 2014 Elsevier B.V.Item Influence of planetary ball milling parameters on the mechano-chemical activation of fly ash(Elsevier, 2015) Patil, A.G.; Anandhan, S.This study illustrates the design of statistical analysis by Taguchi methodology to obtain nanostructured fly ash by planetary ball milling. An orthogonal array and analysis of variance were employed to analyze the effect of milling parameters. A class-F fly ash was subjected to planetary ball milling induced mechano-chemical activation aided by a surfactant. Ball milling parameters, such as ball-to-powder weight ratio, type and quantity of surfactant and type of medium were varied as guided by the Taguchi design. The nanostructured fly ash was characterized by dynamic light scattering, BET surface area analysis, X-ray diffraction, FTIR spectroscopy, scanning electron microscopy, field emission scanning electron microscopy and transmission electron microscopy. The ball-to-powder weight ratio and the surfactant type are the major influencing factors on lower crystallite size and average particle size and higher specific surface area. The surface modification of fly ash was confirmed by FTIR spectroscopy. The nano fly ash produced by this method has a wide application potential in polymer industries as reinforcement in composites. © 2015 Elsevier B.V.Item Nanostructured Fly Ash as Reinforcement in a Plastomer-Based Composite: A New Strategy in Value Addition to Thermal Power Station Fly Ash(Springer Netherlands, 2016) Patil, A.G.; Mahendran, A.; Anandhan, S.Class-F fly ash (FA) from a coal-fired thermal power station was subjected to high energy ball milling-induced mechanochemical activation aided by a surfactant. Subsequently, ethylene-octene copolymer/mechanochemically activated FA (EOC/MCA-FA) composites were prepared by solution casting. The surface modification of FA was confirmed from contact angle measurements and FTIR spectroscopy, which accounts for a good interaction between MCA-FA and the polymer matrix. X-ray diffraction reveals that the crystallite size of quartz phase present in FA got reduced, while the relative lattice strain on it increased during milling. Morphological studies revealed that interfacial adhesion between the polymer and MCA-FA is good and this accounts for the improvement in mechanical properties of the composites even at the minimum filler loading. Flame retardance of the matrix polymer is improved by the addition of either fresh FA or MCA-FA. The results imply that FA is a valuable reinforcing filler for ethylene-octene copolymer and its mechanochemical activation is an effective strategy for its future use. © 2014, Springer Science+Business Media Dordrecht.Item Fault diagnosis studies of face milling cutter using machine learning approach(Multi-Science Publishing Co. Ltd claims@sagepub.com, 2016) Madhusudana, C.K.; Budati, S.; Gangadhar, N.; Kumar, H.; Narendranath, S.Successful automation of a machining process system requires an effective and efficient tool condition monitoring system to ensure high productivity, products of desired dimensions, and long machine tool life. As such the component's processing quality and increased system reliability will be guaranteed. This paper presents a classification of healthy and faulty conditions of the face milling tool by using the Naive Bayes technique. A set of descriptive statistical parameters is extracted from the vibration signals. The decision tree technique is used to select significant features out of all statistical extracted features. The selected features are fed to the Naive Bayes algorithm. The output of the algorithm is used to study and classify the milling tool condition and it is found that the Naive Bayes model is able to give 96.9% classification accuracy. Also the performances of the different classifiers are compared. Based on the results obtained, the Naive Bayes technique can be recommended for online monitoring and fault diagnosis of the face milling tool. © 2016 The Author(s).Item Characterization of composites based on biodegradable poly(vinyl alcohol) and nanostructured fly ash with an emphasis on polymer-filler interaction(SAGE Publications Ltd info@sagepub.co.uk, 2016) Patil, A.G.; SelvaKumar, M.; Anandhan, S.A thermal power station fly ash (FA) was mechanochemically activated by high-energy ball milling that yielded nanostructured FA. This nanostructured FA was incorporated into biodegradable poly(vinyl alcohol) (PVA) matrix by solution mixing and ultrasonication. Transmission electron micrographs revealed that the smooth spherical particles of FA were changed into irregular and rough ones; in addition, the particle size of FA was reduced to a few hundred nanometers, and its specific surface area value increased after the high-energy milling process. All these factors, in turn, led to a thermodynamically favorable interaction between the mechanochemically activated FA and PVA as evidenced by Fourier transform infrared spectroscopy. The incorporation of a very small amount of the nanostructured FA led to an increase in crystallinity of the polymer matrix. The glass transition temperature of the PVA matrix increased by about 18°C when 5 wt% of the nanostructured FA was used as the reinforcement. © The Author(s) 2014.