Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item Influence of planetary ball milling parameters on the mechano-chemical activation of fly ash(Elsevier, 2015) Patil, A.G.; Anandhan, S.This study illustrates the design of statistical analysis by Taguchi methodology to obtain nanostructured fly ash by planetary ball milling. An orthogonal array and analysis of variance were employed to analyze the effect of milling parameters. A class-F fly ash was subjected to planetary ball milling induced mechano-chemical activation aided by a surfactant. Ball milling parameters, such as ball-to-powder weight ratio, type and quantity of surfactant and type of medium were varied as guided by the Taguchi design. The nanostructured fly ash was characterized by dynamic light scattering, BET surface area analysis, X-ray diffraction, FTIR spectroscopy, scanning electron microscopy, field emission scanning electron microscopy and transmission electron microscopy. The ball-to-powder weight ratio and the surfactant type are the major influencing factors on lower crystallite size and average particle size and higher specific surface area. The surface modification of fly ash was confirmed by FTIR spectroscopy. The nano fly ash produced by this method has a wide application potential in polymer industries as reinforcement in composites. © 2015 Elsevier B.V.Item Nickel-oxide multiwall carbon-nanotube/reduced graphene oxide a ternary composite for enzyme-free glucose sensing(Royal Society of Chemistry, 2016) Prasad, R.; Ganesh, V.; Badekai Ramachandra, B.R.We report a solvent-free method of preparation for a NiO-carbon nanotube/graphene ternary composite using nickel formate as a green precursor via a thermal decomposition method. In this ternary composite, NiO with an average particle size of 7 nm is regularly decorated on the surfaces of conductive carbon matrix networks such as MWCNTs and reduced graphene oxide (rGO). Here rGO serves as an ideal support for the uniform distribution of NiO nanoparticles and also functions as an efficient transducer material, whereas, MWCNTs act as a spacer between rGO, which enhances the electrical conductivity and accessibility of the active reaction sites for direct glucose oxidation. The electrochemical performances were evaluated by cyclic voltammetry and amperometric techniques. Under the optimal conditions, the 20 wt% NiO-MWCNT/rGO/GCE exhibits a sensitivity of 4223.3 ?A cm-2 mM-1 and a detection limit of 0.92 ?M over a linear glucose concentration range up to 19 mM. Furthermore, the constructed sensor is effectively employed to detect glucose in real human blood serum samples with adequate results. The modified 20 wt% NiO-MWCNT/rGO/GCE also shows a high sensitivity, greater selectivity, excellent reproducibility and long-term stability. © 2016 The Royal Society of Chemistry.Item Photoluminescence Quenching in Metal Ion (Cu2+, Co2+) Interacted Graphene Quantum Dots(Wiley-VCH Verlag info@wiley-vch.de, 2017) Mishra, P.; Badekai Ramachandra, B.R.Graphene quantum dots (GQD) are nanosized fragments of graphene with finite band gap. Thus, GQDs show excellent photoluminescence (PL) and also possess good electrochemical properties. In the present study, we synthesized GQDs via hydrothermal (HT) method using Graphene oxide as prepared from improved Hummer's method as a precursor with several modifications. The effect of the variation in the photoluminescence and electrochemical properties of the as-prepared GQDs were studied. Average particle size of the as-synthesized GQDs was roughly 30 nm and produced blue PL on excitation with a wavelength of 365 nm. On reacting the GQDs with Cupric Nitrate and Cobalt Nitrate in separate batches, a significant decrease in the intensity of PL was observed. This quenching of PL of GQDs has been utilized in the qualitative estimation of Metal ion (Cu2+ and Co2+) species in aqueous media. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, WeinheimItem Effect of O2, N2 and H2 on annealing of pad printed high conductive Ag-Cu nano-alloy electrodes(Institute of Physics Publishing helen.craven@iop.org, 2018) Manjunath, G.; Anusha, P.; Salian, A.; Gupta, B.; Mandal, S.In this study, annealing of pad printed Ag-Cu based conducting ink was studied in oxidizing, inert and reducing atmosphere to verify its oxidation dependent conductivity. Ag-Cu manually was formulated adopting polyol method; where silver nitrate and copper nitrate serve as initial metal precursors. Polyvinylpyrrolidone (PVP), ethylene glycol and sodium borohydride act as a stabilizer, solvent and reducing agent respectively. The nanoalloys were with an average particle size ?48 ±15 nm, capped with polyvinylpyrrolidone to avoid agglomeration and stable in non-polar solvents. Formation of nanoalloy, Ag 90 wt%-Cu 10 wt%, was verified through a peak shift in UV-visible spectroscopy, found at 470 nm along with Nelson-Relay curve fitting and x-ray photoelectron spectroscopy study. The calculated lattice parameter of nanoalloy ?4.034 Å, was in between pure silver and copper. The crystallite size was calculated using Debye-Scherrer, Williamson-Hall isotropic strain model and Halder-Wagner method. Electrode patterns were printed on a glass substrate by pad printing and were annealed under O2, N2 and H2 atmosphere to study the oxidation kinetics of copper. A maximum conductivity of -6.6 ×;105 S m-1 was observed in inert atmosphere annealing as the conductivity is solely depends on the oxidation of copper; appears with uttermost Cu0 and least Cu2+ in x-ray photoelectron spectroscopy. High conductive space required between manually and dispersion ink can have a potential application as an electrode in printed electronics. Further refinement of size of the nanopaticles by polyol method could help to obtain the effect of quantum confinement. © 2018 IOP Publishing Ltd.Item Praseodymium doped ceria as electrolyte material for IT-SOFC applications(Elsevier Ltd, 2018) Shajahan, I.; Ahn, J.; Nair, P.; Medisetti, S.; Patil, S.; Niveditha, V.; Uday Bhaskar Babu, G.; Prasad Dasari, H.P.; Lee, J.-H.Praseodymium-doped ceria (PDC, Ce0.9Pr0.1O2) electrolyte material for intermediate temperature solid oxide fuel cells (IT-SOFCs) has been successfully synthesised by EDTA-citrate method. From X-Ray diffraction (XRD), fluorite structure along with a crystallite size of 5.4 nm is obtained for PDC nanopowder calcined at 350 °C/24 h. Raman spectroscopy confirmed the structure, presence of oxygen vacancies with the manifestation of the main peak at 457 cm?1 and with a secondary peak at 550 cm?1. From Transmission Electron Microscopy (TEM) analysis, the average particle size is around 7–10 nm and selected area electron diffraction (SAED) patterns further confirmed the fluorite structure of PDC nanopowder. The PDC nanopowder displayed a BET surface area of 65 m2/g with a primary particle size of ?13 nm (calculated from BET surface area). Dilatometer studies revealed a multi-step shrinkage behaviour with the multiple peaks at 522, 1171 and 1461 °C which may be originated due to the presence of multiple size hard agglomerates. The PDC electrolyte pellet sintered at 1500 °C displayed an ionic conductivity of 1.213E-03 S cm?1 along with an activation energy of 1.28eV. Instead of a single fluorite structure, XRD of sintered PDC pellet showed multiple structures (Fluorite structure (CeO2) and cubic structure (PrO2). © 2018 Elsevier B.V.