Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
74 results
Search Results
Item Electrochemical comparison of nickel and nickel hydroxide nanoparticles composited with reduced graphene oxide and polyaniline for their supercapacitor application(American Institute of Physics Inc. subs@aip.org, 2018) Viswanathan, A.; Nityananda Shetty, A.The reduced graphene oxide/polyaniline/Ni(OH)2 (GP-Ni(OH)2) and reduced graphene oxide/polyaniline/Ni (GP-Ni) nanocomposites were synthesized by facile in situ single step chemical method. The constituents were confirmed by powder-XRD, and the electrochemical characterizations were carried out using cyclic voltammetry(CV), galvanostatic charge/discharge (GCD) and electrochemical impedance spectroscopy (EIS). The electrochemical contribution of Ni(OH)2 and Ni to their supercapacitance along with reduced graphene oxide and polyaniline was compared. The GP-Ni nanocomposite exhibited a specific capacitance of 266.66 F g-1, energy density of 53.33 W h kg-1 and power density of 1385 W kg-1 at a current density of 0.25 A g-1 and the results were enhanced to 21% and more promising than that of nanocomposite GP-Ni(OH)2. © 2018 Author(s).Item Abstract Studies have been conducted on the effect of overstressing in rotary bending fatigue on the fatigue properties of an annealed and austempered ductile iron containing 1.5 Ni–0.3 Mo. For various R ratios S–N curves were determined and the fatigue limit estimated. It was found that the fatigue limit was a function of the level of overstressing and cycle ratio. In the case of austempered samples a beneficial effect of overstressing was observed at a certain level of overstressing. This was related to the work hardening behaviour of the austenite phase. In annealed samples, a reduction in the fatigue limit was observed at all levels of overstressing. Copyright © 1995, Wiley Blackwell. All rights reserved(EFFECT OF OVERSTRESSING ON FATIGUE BEHAVIOUR OF AUSTEMPERED DUCTILE IRON) Prasad Rao, P.; Padmaprabha1995Item Rotating bending fatigue tests were carried out on austempered ductile iron containing 1.5 wt% nickel and 0.3 wt% molybdenum. The ductile iron was austenitized at 900 or 1050 °C and then austempered at 280 or 400 °C for different lengths of time to obtain different microstructures. The fatigue strength was correlated with the amount of retained austenite and its carbon content, which were both determined by X-ray diffraction technique. While the tensile strength decreased with increasing retained austenite content, the fatigue strength was found to increase. Carbide precipitation was found to be detrimental to fatigue strength. Lower austenitizing temperature resulted in better fatigue strength. © 1994 Chapman & Hall.(Kluwer Academic Publishers, Effect of microstructure on the fatigue strength of an austempered ductile iron) Shanmugam, P.; Prasad Rao, P.; Rajendra Udupa, K.; Venkataraman, N.1994Item Influence of austenitising temperature on the formation of strain induced martensite in austempered ductile iron(2008) Daber, S.; Ravishankar, K.S.; Prasad Rao, P.P.The present work was taken up to study the influence of austenitising temperature on the formation of strain-induced martensite in austempered ductile iron. Ductile iron containing 1.5 wt.% nickel, 0.3 wt.% molybdenum and 0.5 wt.% copper was subjected to austempering treatments which consisted of three austenitising temperatures, namely 850, 900 and 950 °C, and three austempering temperatures, namely 300, 350 and 400 °C. Tensile tests were carried out under all the heat-treatment conditions and strain-hardening behaviour was studied by applying Hollomon equation. Microstructures were studied by optical microscopy and X-ray diffraction. It was found that increasing austenitising temperature increased the tendency for the formation of strain-induced martensite at all the austempering temperatures. © 2008 Springer Science+Business Media, LLC.Item Optimization and analysis of nickel adsorption on microwave irradiated rice husk using response surface methodology (RSM)(2009) Ganesapillai, M.G.; Iyyaswami, I.; Helen Kalavathy, M.H.; Murugesan, T.; Miranda, L.R.Background: The removal of heavy metals using adsorption techniques with low cost biosorbents is being extensively investigated. The improved adsorption is essentially due to the pores present in the adsorbent. One way of improving the porosity of the material is by irradiation of the precursor using microwaves. In the present study, the adsorption characteristics of nickel onto microwave-irradiated rice husks were studied and the process variables were optimized through response surface methodology (RSM). Result: The adsorption of nickel onto microwave-irradiated rice husk (MIRH) was found to be better than that of the raw rice husk (RRH). The kinetics of the adsorption of Ni(II) from aqueous solution onto MIRH was found to follow a pseudo-second-order model. Thermodynamic parameters such as standard Gibbs free energy (?G°), standard enthalpy (?H°), and standard entropy (?S°)were also evaluated. The thermodynamics of Ni(II) adsorption onto MIRH indicates that it is spontaneous and endothermic in nature. The response surface methodology (RSM) was employed to optimize the design parameters for the present process. Conclusion: Microwave-irradiated rice husk was found to be a suitable adsorbent for the removal of nickel(II) ions from aqueous solutions. The adsorption capacity of the rice husk was found to be 1.17 mg g-1. The optimized parameters for the current process were found as follows: adsorbent loading 2.8 g (100 mL)-1; Initial adsorbate concentration 6 mg L-1; adsorption time 210 min.; and adsorption temperature 35°C. © 2008 Society of Chemical Industry.Item Synthesis, characterization of N, N?-bis(2-hydroxynaphthalidene) phenylene- 1,2-diamine with M(II)(M = Ni, Zn and Fe) Schiff-base complexes and their non-linear optical studies by z-scan technique(Elsevier B.V., 2010) Kumar, H.C.S.; Badekai Ramachandra, B.; Rudresha, B.J.; Ravindra, R.; Philip, R.Schiff-base complexes of N,N?-bis(2-hydroxynaphthalidene)phenylene-1, 2-diamine ligand with metal M (M = Ni(II), Zn(II) and Fe(II)) have been synthesized and characterized by their UV, FT-IR, NMR, elemental analysis and magnetic susceptibility measurements. Non-linear optical measurements carried out using nanosecond laser pulses at 532 nm show that these complexes can be used for optical limiting applications. © 2010 Elsevier B.V. All rights reserved.Item Development of anti-corrosive multi-layered coatings of zinc-nickel alloy(2011) Subbaiah, Y.; Kaje, V.; Hegde, A.C.Purpose: The purpose of this paper is to develop and optimize anti-corrosive multi-layered coatings of zinc-nickel alloy on carbon steel. Design/methodology/approach: A variety of composition-modulated multi-layer alloy (CMMA) coatings of zinc-nickel were developed on a carbon steel substrate by cyclic changes in cathode current during electrodeposition, coupled with variation of the thicknesses of the individual layers. The corrosion behavior of the coatings was studied in 5 percent NaCl solution by electrochemical methods. Cyclic cathode current densities (CCCDs) and the number of alloy layers were optimized for highest performance of the coatings against corrosion. The factors responsible for improved corrosion resistance were analyzed in terms of change in the intrinsic electrical properties of the capacitance value at the electrical double layer that was associated with micro/nanometric layering. The formation of the semi-conductive surface film, which was responsible for the improved corrosion resistance, was supported by a Mott-Schottky plot and the cyclic polarization study. The formation of multi-layered deposit and the mechanism of corrosion degradation of the coating were analyzed using scanning electron microscopy. Findings: CMMA coatings with an optimal configuration of (Zn-Ni)2.0/4.0/300 showed ~35 times better corrosion resistance compared to a monolithic (Zn-Ni)3.0 alloy coating of the same thickness. The peak performance was attributed to the change in intrinsic electrical properties of the coating and this conclusion was supported by dielectric spectroscopy. Originality/value: The paper describes the optimization of CCCD and the number of deposited layers by development of electrolytic deposition of anti-corrosive multi-layered zinc-nickel coatings from a single plating technique. © Emerald Group Publishing Limited.Item Wetting behaviour and interfacial microstructure of Sn-Ag-Zn solder alloys on nickel coated aluminium substrates(2011) Satyanarayan, S.; Prabhu, K.N.Wetting behaviours of two lead free solders (Sn-2·625Ag- 2·25Zn and Sn-1·75Ag-4·5Zn) on nickel coated aluminium substrates were investigated. Sn-2·625Ag-2·25Zn exhibited better wettability compared to Sn-1·75Ag-4·5Zn solder. Contact angles of the solders increased with increasing roughness of the substrate. The Young-Dupre equation was used to evaluate the work of adhesion of solder on the substrate. Sn-2·625Ag-2·25Zn solder exhibited higher work of adhesion than Sn-1·75Ag-4·5Zn. A thin continuous layer of Ni 3Sn was detected at the interface between Sn-2·625Ag- 2·25Zn solder and nickel coated Al substrate. Sn-1·75Ag- 4·5Zn solder exhibited scallop intermetallic compounds (IMCs) growing into the solder field as well as a thin continuous IMC in some cases. Ni 3Sn and Ni3Sn4 IMCs were observed at the interface of Sn-1·75Ag-4·5Zn solder and nickel coated Al. © 2011 Institute of Materials, Minerals and Mining.Item Role of nickel filler on friction and dry sliding wear behavior of bismaleimide nanocomposite(2011) Kurahatti, R.V.; Surendranathan, A.O.; Srivastava, S.; Singh, N.; Ramesh Kumar, A.V.; Kori, S.A.Nano-sized metal particles filled polymer composites are finding numerous tribological applications in recent years. In the present work, the matrix properties were investigated by introducing nickel (Ni) nanoparticles (60-100 nm, weight fractions of 0.5-10 %) into a bismaleimide (BMI) resin. The influence of these particles on the microhardness, friction and dry sliding wear behavior were measured using microhardness tester, pin-ondisc wear set up. The experimental results indicated that the coefficient of friction and the specific wear rate (SWR) of BMI resin can be reduced at rather low weight fraction of Ni particles. The lowest SWR of 9 ×10 -6 mm 3/Nm (i.e. 50% lower than the value of neat BMI) was observed for the nanocomposite with Ni weight fraction of 1%. The incorporation of Ni particles leads to an increased hardness of BMI and the wear performance of the composites shows good correlation with the hardness. The results have been supplemented with scanning electron micrographs to help understand the possible wear mechanisms. © 2011 CAFET-INNOVA TECHNICAL SOCIETY.Item Synthesis and characterization of schiff base metal complexes and reactivity studies with malemide epoxy resin(Korean Chemical Society sunlee@kcsnet.or.kr, 2012) Lakshmi, B.; Shivananda, K.N.; Prakash, G.A.; Isloor, A.M.; Mahendra, K.N.A novel malemide epoxy containing Co(II), Ni(II) and Cu(II) ions have been synthesized by curing malemide epoxy resin (MIEB-13) and Co(II), Ni(II) and Cu(II) complexes of macrocyclic bis-hydrazone Schiff base. The Schiff base was synthesized by reacting 1,4-dicarbnyl phenyl dihydrazide with 2,6-diformyl-4-methyl phenol. The Schiff base and its Co(II), Ni(II) and Cu(II) complexes have been characterized by elemental analyses, spectral (IR, 1H NMR, UV-vis., FAB mass, ESR), thermal and magnetic data. The curing reaction of maleimide epoxy compound with metal complexes was studied as curing agents. The stability of cured samples was studied by thermo-gravimetric analyses and which have excellent chemical (acid/alkali/solvent) and water absorption resistance. Further, the scanning electron microscopy (SEM) and definitional scanning colorimetric (DSC) techniques were confirmed the phase homogeneity of the cured systems.