Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
23 results
Search Results
Item Characterization of p-CdTe/n-CdS hetero-junctions(2009) Mahesha, M.G.; Bangera, K.V.; Shivakumar, G.K.Nano-crystalline CdTe/CdS thin film hetero-junctions have been grown on glass substrate by thermal evaporation technique. The growth conditions to get stoichiometric compound films have been optimized. The grown hetero-junctions have been characterized for their I-V characteristics. Analysis of I-V characteristics has been made to investigate the current conduction mechanism in p-CdTe/n-CdS hetero-junction. The band gap energy of cadmium telluride and cadmium sulfide films have been computed from the study of variation of resistance with temperature. Based on the study, band diagram for p-CdTe/n-CdS hetero-junction has been proposed.Item Preparation and characterization of CdxZn1-xS thin films by spray pyrolysis technique for photovoltaic applications(2009) Raviprakash, Y.; Bangera, K.V.; Shivakumar, G.K.CdxZn(1-x)S (x = 0, 0.2, 0.4, 0.6, 0.8, and 1) thin films were deposited by the chemical spray pyrolysis technique using a less used combination of chemicals. Depositions were done at 573 K on cleaned glass substrates. The composition, surface morphology and structural properties of deposited films were studied using EDAX, SEM and X-ray diffraction technique. XRD studies reveal that all the films are crystalline with hexagonal (wurtzite) structure and inclusion of Cd into the structure of ZnS improved the crystallinity of the films. In the entire compositions, the (0 0 2) diffraction peak is prominent which gives lattice matching to the chalcogenide semiconductor such as CuInxGa1-xSe2 and CuIn (s1-xSex)2, which are used in photovoltaic devices. The value of lattice constant 'a' and 'c' have been observed to vary with composition from 0.382 to 0.415 nm and 0.625 to 0.675 nm, respectively. The band gap of the thin films varied from 3.32 to 2.41 eV as composition varied from x = 0.0 to 1.0. It was observed that presence of small amount of cadmium results in marked changes in the optical band gap of ZnS. © 2009 Elsevier Ltd. All rights reserved.Item Growth, structural and optical properties of CdxZn1-xS thin films deposited using spray pyrolysis technique(2010) Raviprakash, Y.; Bangera, K.V.; Shivakumar, G.K.CdxZn(1-x)S (x = 0, 0.2, 0.4, 0.6, 0.8, and 1) thin films were deposited by the chemical spray pyrolysis technique using a less used combination of chemicals. Depositions were done at 573 K on cleaned glass substrates. The composition, surface morphology and structural properties of deposited films were studied using EDAX, SEM and X-ray diffraction technique. XRD studies reveal that all the films are crystalline with hexagonal (wurtzite) structure and inclusion of Cd into the structure of ZnS improved the crystallinity of the films. The value of lattice constant 'a' and 'c' have been observed to vary with composition from 0.382 to 0.415 nm and 0.625 to 0.675 nm, respectively. The band gap of the thin films varied from 3.32 to 2.41 eV as composition varied from x = 0.0-1.0. It was observed that presence of small amount of cadmium results in marked changes in the optical band gap of ZnS. © 2009 Elsevier B.V. All rights reserved.Item Air quality assessment of Dhanbad District, India - A case study(2010) Anantharamu, A.; Singh, G.; Venkat Reddy, D.Ambient air pollution status in Dhanbad district is studied and presented in this article. The selection of Dhanbad is made considering its importance and the nature of activities taking place around the district. For the assessment of ambient air quality in Dhanbad, the following five locations were chosen: Main Gate of Indian School of Mines(ISM), Dhanbad: It is a site representing purely commercial activities and road traffic. Bankmore: It is one of the busiest marketing centres of the district and is surrounded by residential areas. All the vehicles going to Bokaro pass by this place and thus the traffic density is pretty high. Kusunda: It is a place 10.9 kilometres from Dhanbad Railway Station. It is just beside one of the coal mines, hence, all vehicles going to the mine passes through this place. Steel Gate: It consists of a small market. Trucks and other heavy vehicle are more frequent during night as this road connects to a highway. ISM Admin Block: It can be considered as a sensitive area since it is a very calm place where the usage of vehicles is minimum throughout the day. Monitoring of ambient air quality is done following the standard procedure prescribed in IS: 5182. In addition, the concentration of lead, zinc, cadmium, copper, manganese and iron metals in SPM is also monitored. The ambient air quality assessment was done in the month of June, 2009. The concentration of SPM was higher than the permissible limit in three locations namely ISM Main Gate, Bankmore and Steel Gate, while it was less than the permissible limit in other two locations, ISM Admin Block and Kusunda. Since the generation of SPM was mainly due to vehicular traffic it was expected to cross the limit in the above mentioned three locations as density of vehicular movement is very high. © 2010 CAFET-INNOVA TECHNICAL SOCIETY.Item The uptake mechanism of Cd(II), Cr(VI), Cu(II), Pb(II), and Zn(II) by mycelia and fruiting bodies of Galerina vittiformis(Hindawi Publishing Corporation 410 Park Avenue, 15th Floor, 287 pmb New York NY 10022, 2013) Damodaran, D.; Mohan Balakrishnan, R.M.; Shetty K, K.Optimum concentrations of heavy metals like copper, cadmium, lead, chromium, and zinc in soil are essential in carrying out various cellular activities in minimum concentrations and hence help in sustaining all life forms, although higher concentration of these metals is lethal to most of the life forms. Galerina vittiformis, a macrofungus, was found to accumulate these heavy metals into its fleshy fruiting body in the order Pb(II) > Cd(II) > Cu(II) > Zn(II) > Cr(VI) from 50 mg/kg soil. It possesses various ranges of potential cellular mechanisms that may be involved in detoxification of heavy metals and thus increases its tolerance to heavy metal stress, mainly by producing organic acids and phytochelatins (PCs). These components help in repairing stress damaged proteins and compartmentalisation of metals to vacuoles. The stress tolerance mechanism can be deduced by various analytical tools like SEM-EDX, FTIR, and LC-MS. Production of two kinds of phytochelatins was observed in the organism in response to metal stress. © 2013 Dilna Damodaran et al.Item Role of cadmium on corrosion resistance of Zn-Ni alloy coatings(Allerton Press Inc. journals@allertonpress.com, 2014) Rao, V.R.; Hegde, A.C.Cadmium (Cd) catalyzed Zn-Ni alloy plating has been accomplished galvanostatically on mild steel (MS) using gelatin and glycerol as additives. The effect of addition of Cd into Zn-Ni bath has been examined in terms of nickel (Ni) content and corrosion resistance of Zn-Ni-Cd ternary alloy coatings. The process and product of electrolysis under different concentrations of additives and Cd have been investigated by cyclic voltammetry (CV). The effects of current density (c.d.) on Ni content of the alloy have been studied by spectrophotometric method, supported by EDX analysis. The deposition has been carried out under different concentrations of Cd ranging from 0.004 to 0.1 M. The corrosion rates (CR) of Zn-Ni alloy coatings have been found to decrease drastically with addition of Cd. It has been also revealed that the CR of binary Zn-Ni alloy coatings decreased with the increase of Cd concentration only up to a certain optimal concentration, i.e., up to 0.02 M, and then remained unchanged. An effort to change the anomalous type of codeposition into normal one by changing the molar ratios of the metal ions, i.e. [Cd2+]/[Ni2+] as 0.01, 0.05 and 0.25 has remained futile. CV study demonstrated an important role of Cd in mutual depositions of Zn2+ and Ni2+ ions by its preferential adsorption, thus leading to the increased Ni content of the alloy. The bath composition and operating parameters have been optimized for deposition of bright and uniform Zn-Ni-Cd alloy coatings. Changes in the surface morphology and phase structure of Zn-Ni alloy coatings due to addition of Cd has been confirmed by Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD) study respectively. Experimental investigations so as to identify the role of Cd in codeposition Zn-Ni alloy coatings have been carried out and the results are discussed. © 2014 Allerton Press, Inc.Item Cadmium (II) and nickel (II) biosorption by Bacillus laterosporus (MTCC 1628)(Taiwan Institute of Chemical Engineers, 2014) Kulkarni, R.; Shetty K, V.; Srinikethan, G.Biosorption of heavy metals is a promising technology that involves removal of toxic metals from industrial waste streams and natural waters. The study describes the sorption of cadmium (II) [Cd (II)] and nickel (II) [Ni (II)] by dead biomass of Bacillus laterosporus, MTCC 1628. The biosorption conditions for the removal of Cd (II) and Ni (II) were examined by studying the effect of pH, contact time, biosorbent dosage and initial metal ion concentration. Shake flask studies yielded adsorption equilibrium in almost 120. min, for both the metals. It was found from Langmuir model that the maximum adsorption capacity for Cd (II) and Ni (II) ions was 85.47. mg/g and 44.44. mg/g respectively. Kinetic evaluation of the experimental data showed that the biosorption process followed pseudo-second order kinetics. Thermodynamic analysis showed that biosorption is an endothermic process with ?. H° of 5.45. kJ/mol for Cd (II) biosorption and 24.33. kJ/mol for Ni (II) biosorption. The surface characteristics of B. laterosporus biomass before and after metal biosorption were analyzed by using scanning electron microscope (SEM) with energy dispersive X-ray spectroscopy (EDAX) to study the changes in surface morphology and elemental constitution of the adsorbent. B. laterosporus exhibited a higher and better potential biosorbent for the removal of Cd (II) as compared to Ni (II) from aqueous solution. © 2013 Taiwan Institute of Chemical Engineers.Item Synthesis and characterization of novel sulfanilic acid-polyvinyl chloride-polysulfone blend membranes for metal ion rejection(Royal Society of Chemistry, 2016) Nayak, V.; Jyothi, M.S.; Balakrishna, R.G.; Padaki, M.; Isloor, A.M.Near-complete removal of heavy metals, namely Cd(ii), Cr(vi) and Pb(ii), has been attempted by a membrane purification process using a blend of modified polyvinyl chloride (PVC) and polysulfone (PSf), prepared by the diffusion induced phase separation (DIPS) method. The prepared novel material was characterized by NMR, ATR-IR spectroscopy and DSC. The sulphonyl groups incorporated into PVC enhance the hydrophilicity and are substantiated by water uptake, contact angle (CA) and flux studies. The obtained properties of the blend membrane like increased surface roughness and porosity are observed from AFM and SEM analysis. An enhanced rejection of ?95% which is about 1.15, 1.41 and 1.37 times better than the commercially available NF 270 membrane was observed, for Cd(ii), Cr(vi) and Pb(ii) respectively. The work was further extended to study the antifouling property and the interference of other existing metal ions on the performance. An improved antifouling property with 98.5% rejection for bovine serum albumin (BSA) and a 75.6% flux recovery ratio (FRR) was achieved. The study gains significance in exploring the incorporation of sulphonyl groups in to polymers, to enhance membrane performance. © The Royal Society of Chemistry 2016.Item Properties of CdxZn1-xO thin films and their enhanced gas sensing performance(Elsevier Ltd, 2017) Bharath, S.P.; Bangera, K.V.; Shivakumar, G.K.CdxZn1-xO(0 ? x ? 0.20) thin films with different Cd concentrations were successfully deposited on glass substrate using spray pyrolysis technique. X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray analysis (EDAX) were used for structural, surface morphological and compositional characterization. The XRD analysis revealed that the synthesized films were hexagonal in structure with (002) orientation. The SEM studies confirm the formation of homogeneous and uniform films. Optical transmittance and electrical conductivity of the films were evaluated using UV–Visible spectroscopy and two probe method respectively. The optical studies showed that the CdxZn1-xO thin films have optical transmittance in entire visible region. The resistivity of undoped films were very high and it decreases with addition of cadmium. The gas sensing properties were investigated at optimal temperature of 350 °C for various volatile organic compounds like acetone, ethanol and methanol. The CdxZn1-xO thin films with 10 at. % cadmium concentration showed the sensitivity of 50% for 1 ppm ethanol. © 2017 Elsevier B.V.Item Multi-signaling thiocarbohydrazide based colorimetric sensors for the selective recognition of heavy metal ions in an aqueous medium(Elsevier B.V., 2017) Momidi, B.K.; Tekuri, V.; Trivedi, D.R.A series of colorimetric chemosensors R1–R6 have been developed from thiocarbohydrazide derivatives, for the selective detection of heavy metal ions. The structures of the receptors R1–R6 were well characterized by standard spectroscopic techniques like FT-IR, 1H NMR, and ESI-MS. The solid structure of receptor R1 and R2 were derived by single crystal X-ray diffraction (SC-XRD). The cation reorganization abilities of receptors R1–R6 were studied by UV–Vis spectroscopy. The receptors R1, R3 and R4 acts as a tremendous sensitive probe for heavy metal ions (Hg2 +, Cd2 + and Pb2 +) with the ?M detection (R1 for Hg2 +, 2.72, R3 for Cd2 +, 3.22, R4 for Hg2 +, Cd2 + & Pb2 +, 0.70, 0.20 & 0.30 ?M) and the receptors R2, R5 & R6 are sensitive towards Cu2 + ions with the ?M detection (3.34, 0.90 & 1.20 ?M) in an aqueous medium among all other tested cations. The receptor R4 shows a multi-color response towards Hg2 +, Cu2 +, Cd2 + and Pb2 + ions. The recognition mechanism, stoichiometric binding ratio and detection limit (DL) have been examined by UV–Visible spectroscopic titration experiments and Benesi-Hildebrand (B-H) plot, receptor R1–R6 sowed 1:1 binding ratio with good binding constant range of 103 to 105 M? 1 with Hg2 +, Cu2 +, Cd2 + and Pb2 + ions metal ions. © 2017 Elsevier B.V.
- «
- 1 (current)
- 2
- 3
- »