Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Determination of optimal magnetorheological fluid particle loading and size for shear mode monotube damper(Springer Verlag service@springer.de, 2019) Acharya, S.; Saini, R.S.S.; Kumar, H.Magnetorheological (MR) fluids belong to a class of controllable fluids, and the composition and concentration of its components govern its magnetorheological properties. In this study, an optimum particle loading (or mass fraction) and size of iron particles in MR fluid for use in a shear mode monotube MR damper were determined based on the damping force and off-state viscosity of synthesized MR fluid samples. Initially, the morphological and magnetic properties of carbonyl iron particles were characterized. Six MR fluid samples were prepared composed of combination of three different particle loadings and two sizes of iron particles. Magnetorheological tests were conducted on these samples to determine the flow curves at off-state and on-state magnetic field conditions. Herschel–Bulkley model was used for mathematical representation of flow curves at different magnetic fields and to determine their dynamic yield stress. Further, a shear mode monotube MR damper with accumulator was designed by using optimization technique for desired dynamic range and damping force. Magnetostatic analysis was performed to determine the magnetic field strength generated in the shear gap at different currents. The damping force was calculated for synthesized MR fluids based on their dynamic yield stress corresponding to the magnetic field strength in the shear gap. Analysis of variance was performed to analyse the significance of independent factors on the damping force and off-state viscosity of MRF. The optimal particle loading and size which yielded maximum damping force with minimum off-state viscosity were determined using a multi-objective genetic algorithm. © 2019, The Brazilian Society of Mechanical Sciences and Engineering.Item Synthesis of magnetorheological fluid and its application in a twin-tube valve mode automotive damper(SAGE Publications Ltd info@sagepub.co.uk, 2020) Madhavrao Desai, R.; Acharya, S.; Jamadar, M.-E.-H.; Kumar, H.; Joladarashi, S.; Sekaran, S.C.R.The change in rheological properties of smart materials like magnetorheological fluid when brought under the influence of a magnetic field can be utilized to develop magnetorheological devices where the output has to be continuously and quickly varied using electronic control interface. In the present study, magnetorheological fluid is synthesized and used as a smart fluid in a twin-tube magnetorheological damper operating in valve mode. The behavior of the magnetorheological fluid is experimentally characterized in a rheometer and mathematically modeled using Herschel–Bulkley model. The parameters of the Herschel–Bulkley model are expressed as polynomial functions of strength of the magnetic field in order to find the shear stress developed by the magnetorheological fluid at any given strength of the magnetic field applied. The magnetorheological damper, which was designed for application in a passenger van, is tested in the damper testing machine. The performance of the damper at different damper velocities and current supplied is studied. The range of values for the parameters of the experimental testing are chosen to emulate the actual conditions of operation in its intended application. Nondimensional analysis is performed, which links magnetorheological fluid rheological properties and geometrical parameters of magnetorheological damper design with the force developed by the damper. Finite element method magnetics is used to find the strength of the magnetic field at the fluid flow gap. Analytical methods are used to calculate the damper force developed due to the field-dependent yield stress and compared with experimental force values. The resulting dynamic range of the magnetorheological damper is also assessed. © The Author(s) 2020.Item Influence of different fumed silica as thixotropic additive on carbonyl particles magnetorheological fluids for sedimentation effects(Elsevier B.V., 2021) Aruna, M.N.; Rahman, M.R.; Joladarashi, S.; Kumar, H.; Bhat Panemangalore, D.B.The present work reports the influence of different types of surface area, hydrophobic, and hydrophilic fumed silica mixed in silicone oil as a thixotropic additive on carbonyl particles based magnetorheological fluids (MRFs) were prepared. Scanning electron microscopy analysis confirms the fumed silica particles attached to the surfaces of CIPs. The vibrating sample magnetometer result shows the MRF4 and 5 have a better magnetic saturation value of 30.12 emu/gm and 40.12 emu/gm, respectively. The experimental rheological flow curve behaviours are investigated using the magnetorheometer. The Herschel–Bulkley rheological model is found to be in good agreement with the experimental curves and suggested shear thinning property is observed. The results showed that the hydrophilic silica with larger surface area type presented (i.e.MRF 4 and 5) better magnetorheological fluid characteristics in terms of shear stress, with a high value of dynamic yield stress, and have much-improved sedimentation ratio up to seven days. © 2021 Elsevier B.V.Item Effect of temperature on sedimentation stability and flow characteristics of magnetorheological fluids with damper as the performance analyser(Elsevier B.V., 2022) Kumar Kariganaur, A.; Kumar, H.; Arun, M.dimentation stability and high yield stress of a magnetorheological fluid (MRFs) are essential parameters for better damping performance for any practical application. Preliminary investigations have been carried out on carbonyl iron particles to determine the morphology, particle size, crystal structure, and saturation magnetization for their feasibility of synthesizing magnetorheological fluids in-house. This study synthesizes various MRFs from various commonly used carrier oils and additives. The MRF samples were prepared for 25% volume fractions of carbonyl iron (CI) powder in either silicone oil (350cSt) or hydraulic oil (50cSt) and by using lithium and calcium-based additives or a combination of both the additives. The sedimentation stability and yield behaviour at different temperatures show a remarkable drop in sedimentation rate and yield stress for all the MR fluid samples. The characterization of the prepared MR fluids reveals that MRF-1, MRF-3, MRF-5 are more stable and have high yield stress values. MRF-1 is selected to further characterize its dynamic performance in magnetorheological damper fabricated based on geometric dimensions obtained from the response surface optimization technique. The results indicate a 164.45% and 135.48% increase in damping force at higher amplitude and higher frequencies at 0A and 1A currents. Further, similar tests have been carried out by synthesizing MRF-7 with silicone oil (50cSt) + lithium base grease as the additive. The sample's stability and yield stress with temperature are carried out, and performance analysis shows a remarkable change in damping force than MRF-1. The dynamic range obtained is practically viable in MRF-7 than MRF-1, with less variability. Finally, temperature characteristics captured from the thermocouple of the MR damper reveal that an average of 43.78% reduction in damping force when the temperature is increased by 19.5 °C with increased dynamic range. © 2022 Elsevier B.V.Item Effect of reduced geometric dimensions on torque generation in two plate rotor magnetorheological brake with in-house magnetorheological fluid(Institute of Physics, 2023) Kariganaur, A.K.; Kadam, S.; Kumar, H.; Arun, M.The present study is aimed to evaluate the torque generation capacity of a two plate rotor magnetorheological (MR) brake using in-house prepared MR fluid. The prepared MR fluids were studied for sedimentation rate at different temperatures and flow characterization at different currents and at specific temperatures. The yield stress of the fluid is explored through Herschel-Bulkley model. The results depict significant increase in sedimentation rate and decrease in yield stress with increase in temperature of the MR fluid. MR brake (model-1) is fabricated after finite element method magnetics exhibit magnetic field of approximately 0.145 T in the shear gap than other two models (model-2 and model-3) considered in this study. Characterization of the MR brake illustrates that there is an increase in torque with increasing current. Further tests have been carried out to identify the effect of sedimentation on torque generation at 52 °C after 15 h of sedimentation. The results indicate 16% reduction in the initial torque because of settling of particles. MR fluid and particles characterization illustrates that 322 °C and 400 °C are critical points in controlling the MR fluid input parameters. © 2023 IOP Publishing Ltd.Item Determining the optimal composition of magnetorheological fluid for a short-stroke magnetorheological damper(Springer, 2023) Aralikatti, S.S.; Puneet, N.P.; Kumar, H.The current study investigates the effect of viscosity of base oil and weight fraction of carbonyl iron particles on maximum yield stress and effective damping range of a short-stroke magnetorheological damper (stroke length of 2 mm) designed for tool vibration mitigation. It is difficult to find the exact composition of magnetorheological fluid (MRF) based on the design equations, as unidentified practical parameters influence their behaviour hence, optimization by experimental techniques is necessary. Optimal composition of MRF are identified by genetic algorithm through central composite design of experiment. A validation study is conducted to cross verify the optimum values delivered by the algorithm. The damper is fitted onto lathe machine with the optimal fluid composition to evaluate its performance in controlling the tool vibration. The damper has been designed for the specific speed, feed and depth of cut however, the design procedure for developing a damper for higher/other cutting conditions can be achieved by the design scheme mentioned in this article. The vibration level of tool reduced by 28.66% and the amplitude of cutting force reduced by 68.18% indicating reduction of chatter vibration with the damper. An improved surface finish has been observed from 4.8 to 1.6 μm. © 2023, Indian Academy of Sciences.Item Experimental Investigation on Thermal Stability of Dual Particle Magnetorheological Fluid and Performance(Taylor and Francis Ltd., 2024) Kariganaur, A.K.; Kumar, H.; Mahalingam, A.Magnetorheological fluid and their properties are essential in Magnetorheological applications. The present study aims to obtain the thermally stable carrier fluid for Magnetorheological damper application through thermogravimetric analyses of three base fluids for higher stability fluid to synthesize Magnetorheological fluid. Scanning electron microscopic images of particles were also tested for their morphology. Magnetorheological fluid samples with 10%, 15%, and 20% by volume were prepared in-house with a 3% calcium base additive (base fluid). Sedimentation and thermal conductivity studies reveal that increasing particle concentration increases the settling time and thermal conductivity. The flow properties show an increase in yield stress with an increase in particle concentration and magnetic fields. The application part of the fluid consists of Magnetorheological damper fabrication and dynamic testing of 20% volume concentration particles at 10 mm amplitude, 2 Hertz frequency, and 0 Ampere and 0.5 Ampere currents, and the temperature of the system is captured with a K-type thermocouple. The results show an 8.2 °C rise at 0.5 Ampere with a 26.2% force decrease within 1000 cycles. The theoretical model based on the lumped parameter analysis predicts the temperature rise, similar to the experimental analysis with a 9.5% error. © 2023 Taylor & Francis Group, LLC.Item Study on operational temperature of magneto-rheological fluid and design dimensions of magneto-rheological damper for optimization(Institute of Physics, 2024) Kumar Kariganaur, A.; Kumar, H.; Arun, M.This study aims to restrict the upper limit for flow gap and effective length in magnetorheological (MR) damper for optimal performance. Initially, the sedimentation study of in-house MR fluid (25%) shows that an 8% reduction in the sedimentation ratio with the addition of additive and nonlinear Herschel-Bulkley (HB) model fit reflects a 32.5% decrease in average yield stress with increasing currents when the parallel plate gap is increased from 1 mm to 2 mm. Owing to this decrease in yield stress, further study is extended to fabricate two MR dampers with limit values (LV) of flow gap and effective length with a common magnetic outer cylinder. Testing results of MR dampers revealed a 72% reduction in damping force at 0.8 A current when the LV’s is increased from LV-1 to LV-2. Selecting LV-1 over LV-2 as the upper limit for any design optimization will give the MR damper optimal performance. At higher input parameters, amplitude has a 135% greater impact on damping force than frequency and current. It is also demonstrated that saturation magnetization depends on the applied magnetic field and input loading parameters. Finally, gravimetric analysis shows that the effectiveness of the MR fluid and magnetic particle starts to decline after 322 °C and 400 °C. © 2024 IOP Publishing Ltd.