Conference Papers

Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/28506

Browse

Filters

2012 - 20153

Settings

Subject: search.filters.subject.Cooling curve analysis

Search Results

Now showing 1 - 3 of 3
  • No Thumbnail Available
    Item
    Development of clay based nanofluids for quenching
    (2012) Ramesh, G.; Prabhu, K.N.
    In the present work the effect of addition of nanoclay particles having concentrations of 0.001, 0.01 and 0.1 vol% on cooling performance of water during immersion quenching was investigated. Cooling curve analyses were carried out by using standard ISO/DIS 9950 quench probe. Wetting behavior of nanoquenchant was studied using dynamic contact angle analyzer. The spreading behavior of droplets of quench media on INCONEL 600 substrate indicates improved wetting behavior of nanofluids. The peak cooling rate and cooling rate at 700°C for water decreased by addition of nanoparticles. Further, quenching in nanofluid shows longer vapour blanket stage as compared to water. The estimated flux transients and Grossmann H factor clearly show that decreased cooling performance of water by addition of nanoparticles. Copyright © 2012 ASM International® All rights reserved.
  • No Thumbnail Available
    Item
    Assessment of wetting kinematics and cooling performance of select vegetable oils and mineral-vegetable oil blend quench media
    (Trans Tech Publications Ltd ttp@transtec.ch, 2015) Pranesh Rao, K.M.; Prabhu, K.
    Quench hardening is a process where an alloy is heated to solutionizing temperature and held for a definite period, and then rapidly cooled in a quenching medium. Selection of quenchant that can yield desired properties is essential as it governs heat extraction process during quenching. In the present work, the cooling performance of vegetable oil and mineral-vegetable oil blend quench media was assessed. The vegetable oils used in this work were olive oil, canola oil and rice bran oil. The mineral-vegetable oil blends were prepared by blending 10 and 20 vol. % of rice bran and canola oil in mineral oil. Inconel probe of 12.5mm diameter and 60mm height, instrumented with thermocouples were used to characterize quenchants. The probe was heated to 850°C and quenched in the oil medium. The cooling curves at different locations in the probe were used to study wetting kinematics. Inverse modelling technique was used to estimate spatially dependent metal-quenchant interfacial heat flux. It was found that the vegetable oils exhibited very short vapour blanket stage compared to mineral oil and blends. Faster wetting kinematics obtained with blends resulted in uniform heat transfer compared to that of mineral oil. The temperature distribution in the probe quenched in vegetable oils and blends was more uniform compared to that in mineral oil. It is expected that the parts quenched in vegetable oils and blends would lead to better hardness distribution compared to mineral oils. © (2015) Trans Tech Publications, Switzerland.
  • No Thumbnail Available
    Item
    Characterization of metal-PCMs for thermal energy storage applications
    (Trans Tech Publications Ltd ttp@transtec.ch, 2015) Sudheer, R.; Prabhu, K.
    In recent years phase change materials have emerged to be ideal energy storage materials for their higher energy density over sensible heat storing materials. Use of phase change materials (PCM) have been successfully implemented at lower temperature applications with various organic compounds. On the other hand, high temperature applications have been solely dominated by various salts, their eutectics and mixtures as phase change materials. This work discusses the suitability of metals and alloys for thermal energy storage applications as the phase change material. Metals offer superior thermal conductivities with considerable energy density compared to salts. Here, two alloys namely, Sn-0.3Ag-0.7Cu (SAC) solidifying over 212-224°C and ZA8 (Zn-8%Al) solidifying over 378-405°C have been studied. Thermal analysis of PCMs using Computer Aided Cooling Curve Analysis (CA-CCA) and DSC technique were performed to predict the solidification path. In addition to this, Newtonian technique was employed to estimate the latent heat of fusion for these phase change materials. Cooling rate curves and Fraction Solid curves offered a better insight into their ability to receive and discharge heat over the concerned temperature range. © (2015) Trans Tech Publications, Switzerland.