Conference Papers
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/28506
Browse
4 results
Search Results
Item Microstructure and mechanical properties of magnesium alloy processed by equal channel angular pressing (ECAP)(Elsevier Ltd, 2017) Gopi, K.R.; Shivananda Nayaka, H.Equal Channel Angular Pressing (ECAP) with different passes was carried out for Mg-Al-Mn (AM) series magnesium alloy to investigate the microstructure and mechanical properties. ECAP process was carried up to 4 passes using route BC, where the samples are rotated by 90° in the same direction between consecutive passes. Microstructures were studied using optical microscope (OM) and scanning electron microscope (SEM) and it was observed that the grain size was reduced from 100 μm to 1 μm after 4 passes. Tensile test was conducted and the ultimate tensile strength (UTS) increased up to 2 passes but decreased with higher passes, even though grain size became finer with increase in ECAP passes. Microhardness was carried out and it was observed that the hardness was increased up to 2 passes of ECAP and decreased with higher passes. © 2017 Elsevier Ltd.Item Influence of Multi Axial Forging (MAF) on Microstructure and Mechanical Properties of Cu-Ti Alloy(Elsevier Ltd, 2018) Ramesh, S.; Shivananda Nayaka, H.S.; Gopi, K.R.Multi axial forging (MAF) is one among the severe plastic deformation (SPD) processes, where large strains are imposed into the component. In the present work, as-received Cu-1.5%Ti alloy was subjected to MAF for 2 and 4 cycles at room temperature. Microstructure showed grain refinement after 2 and 4 cycles. Average grain size obtained for MAF processed samples after 2 and 4 cycles are 120 μm and 40 μm, respectively compared to initial grain size of 800 μm. The Mechanical properties were analyzed for as-received and MAF processed samples. Tensile test showed increased ultimate tensile strength (493 MPa) for MAF 4-cycle sample compared to as-received (191 MPa) condition with accumulated strain of 2.18 for 4 cycles. Increase in hardness was observed for MAF processed sample of 143 Hv for 4-cycle compared to as-received sample of 67 Hv. © 2018 Elsevier Ltd.Item Influence of cold rolling process on microstructure and mechanical properties of Cu-1.5%Ti alloy(American Institute of Physics Inc. subs@aip.org, 2018) Ramesh, S.; Shivananda Nayaka, H.S.; Anne, G.; Gopi, K.R.The effects of cold rolling on the microstructure evolution and mechanical properties of Cu-1.5%Ti alloy were investigated. The results showed that the tensile strength of the Cu-1.5%Ti alloy increased with an increase of rolling deformation at room temperature. Significant grain refinement took place during rolling process revealed in optical microstructure and transmission electron microscope analysis. XRD patterns revealed peaks indexed to Cu, Cu3-Ti2 and Cu4-Ti3 after 8-pass rolling process. Microhardness of the rolled Cu-1.5%Ti alloy layers increased incessantly with increase in the number of rolling passes. Tensile strength increased up to 294 MPa which was about 1.54 times higher than that of the cast Cu-1.5%Ti alloy. Fracture surfaces of the rolled Cu-1.5%Ti alloy revealed the dimples in the structure, which is an indication of ductile fracture. © 2018 Author(s).Item Electrochemical Behaviour of ECAP-Processed AM Series Magnesium Alloy(Springer International Publishing, 2019) Gopi, K.R.; Shivananda Nayaka, H.Equal channel angular pressing (ECAP) is a technique for inducing high strain into the material to achieve ultrafine grain refinement. AM80 magnesium was processed by ECAP with processing route BC. ECAP-processed samples were tested for microstructural studies and electrochemical measurements. Potentiodynamic polarization test revealed decrease in corrosion current density due to uniform refined microstructure of the processed samples. Increment in charge transfer resistance (Rt) was observed for ECAPed samples with increase in capacitive arc diameters in Nyquist plots showing increased corrosion resistance in comparison with as-cast condition. The increment in corrosion resistance is because of grain refinement and uniform dispersal of intermetallic particles, which improved development of protective layer and bonding due to increased grain boundary density by ECAP process. © 2019, The Minerals, Metals & Materials Society.