Conference Papers
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/28506
Browse
3 results
Search Results
Item Numerical study on fracture behavior of alkali activated concrete mixes for different beam sizes(Elsevier Ltd, 2023) Annappaswamy, G.M.; Channappa, T.M.; Prashanth, M.H.The present study considers the use of AAC mixes, since the raw materials that are being used to produce concrete are non-renewable natural resources, particularly Ordinary Portland Cement (OPC). Also, production of OPC contributes a greater amount of CO2 to the environment. Hence, an attempt has been made to study alternative construction materials keeping in mind sustainable development. The present numerical study compares the fracture behaviour and size effect of Alkali Activated Concrete (AAC) mixes with Ordinary Portland Cement Concrete (OPCC) mixes by numerically modelling the beams of AAC and OPCC using FEA software ABAQUS. Three different mixes of AAC, characterized by the variation of percentage volume of water-quenched slag (WQS) as a substitute for Natural sand (RS) and one OPCC mix, were studied. A three-point bending test was performed in ABAQUS for the beams of three different sizes, which are geometrically similar with constant thickness. Numerical simulation is performed under displacement control. Load versus CMOD graphs are plotted from the output data obtained from the numerical modelling. Fracture parameters such as Fracture energy (GF), Brittleness number (B), Characteristic length (lch), and Stress intensity factor (KIC) are then calculated from the obtained data and compared to understand the influence of fracture properties and size effect on the behaviour of structural elements since limited research works are available from the literature. From the results, it is observed that OPCC mixes show superior strength, high resistance to crack propagation, more toughness, and high fracture energy when compared to AAC mixes. AAC-50 concrete mix has shown better performance compared to the other two AAC mixes, i.e., AAC-0 and AAC-100. The results of this work can certainly be used to predict the non-linear behaviour of concrete and can be adopted in the design of structural elements. © 2023 Elsevier Ltd. All rights reserved.Item Numerical Analysis on Fatigue Behavior of Plain Concrete and Alkali-activated Concrete(Institute of Physics, 2024) Sushanthkumar, K.V.; Channappa, T.M.; Prashanth, M.H.; Chaitra, A.R.Alkali-activated concrete (AAC) has recently gained a lot of potential to become one of the most recommended sustainable replacements for Ordinary Portland cement concrete (OPCC). In the present investigation, an attempt has been made to study the static and fatigue flexural behavior of AAC compared to that of OPCC by using numerical modeling FEA software, ABAQUS. The nonlinear behavior of the stress-strain curve of the concrete has been studied using the concrete damage plasticity (CDP) model. A 2D notched beam was modelled using plane stress condition and three-point bending tests were performed under monotonic loading to obtain the static behavior of concrete. The result obtained has been utilized to fix the loading range for cyclic loads in fatigue analysis and at different loading frequencies. The load-CMOD curves and load-deflection curves were obtained for both static and fatigue loading, and the number of cycles to failure during fatigue. From the results, it has been observed that the Ordinary Portland cement concrete specimens sustain more load than that of Alkali-activated concrete under monotonic loading. However, AAC has shown more resistance to fatigue than that of the OPCC and the frequency of loading significantly influences the fatigue performance. © Published under licence by IOP Publishing Ltd.Item Numerical Study on Static and Fatigue Behavior of Alkali-Activated Fly Ash Concrete Modelled using Concrete Damage Plasticity (CDP) Model(Institute of Physics, 2024) Nandhineekrishna; Channappa, T.M.; Prashanth, M.H.; Kuttagola, K.Alkali-activated concretes (AAC) are considered as an alternative to Portland cement concretes because of their much lower carbon emissions. To study its characteristics is of utmost importance. In the present research, an attempt is made to create a numerical model to analyze the static and fatigue flexural behavior of alkali-activated fly ash concrete (FC) and compare them with ordinary Portland cement concrete (PCC). Three-point bending tests are simulated for the monotonic load to obtain the static behavior of a 2D notched rectangular beam. A 2D beam specimen of size 262.5 mm x 75 mm, with a notch of size 15 mm x 3 mm was provided at the bottom middle. Fly ash-based alkali-activated concrete (FC) and corresponding PCC of similar strength are modeled in ABAQUS CAE using the concrete damage plasticity (CDP) model. The ultimate loads, maximum deflection, and CMOD for each of them were obtained from the history output manager. The results of monotonic tests are utilized for creating a sinusoidal load cycle for fatigue tests with various loading frequencies and stress ratios. Different structural responses are examined under the fatigue test. The results showed that FC performs better than PCC under static and fatigue tests. Fatigue performance of both FC and PCC is influenced by the frequency of loading and fatigue life increases at higher frequencies. It is also found that stress reversal negatively impacts the fatigue life of both FC and PCC. © Published under licence by IOP Publishing Ltd.