Conference Papers

Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/28506

Browse

Author: search.filters.author.Anne, G.

Search Results

Now showing 1 - 4 of 4
  • No Thumbnail Available
    Item
    Microstructure, mechanical and corrosion properties of accumulative roll bonded Mg-2%Zn/anodized Al-7075 composite
    (Elsevier Ltd, 2018) Anne, G.; Ramesh, M.R.; Shivananda Nayaka, H.S.; Arya, S.B.
    Multilayered composite of Mg-2%Zn/anodized Al-7075 was developed by accumulative roll bonding (ARB) of wrought Mg-2%Zn and anodized aluminium 7075 alloy. The Mg-2%Zn/anodized Al-7075 composite exhibited density of 2298 kg/m3 which is about 1.2 times lighter weight as compared to Al-7075 alloy. The electron backscatter diffraction (EBSD), transmission electron microscopy (TEM) showed an average grain size of 1 μm and 0.73 μm in Mg-2%Zn and anodized Al-7075 layers respectively, and with high angle grain boundaries (HAGBs). Mechanical properties were evaluated by microhardness and tensile tests and found significant improvement in strength and hardness values as compared with Mg-2%Zn alloy after four pass ARB process. The multilayered composite shows better corrosion resistance as compared to rolled Mg-2%Zn alloy evaluated using using potentiodynamic polarization test. © 2017 Elsevier Ltd.
  • No Thumbnail Available
    Item
    Influence of cold rolling process on microstructure and mechanical properties of Cu-1.5%Ti alloy
    (American Institute of Physics Inc. subs@aip.org, 2018) Ramesh, S.; Shivananda Nayaka, H.S.; Anne, G.; Gopi, K.R.
    The effects of cold rolling on the microstructure evolution and mechanical properties of Cu-1.5%Ti alloy were investigated. The results showed that the tensile strength of the Cu-1.5%Ti alloy increased with an increase of rolling deformation at room temperature. Significant grain refinement took place during rolling process revealed in optical microstructure and transmission electron microscope analysis. XRD patterns revealed peaks indexed to Cu, Cu3-Ti2 and Cu4-Ti3 after 8-pass rolling process. Microhardness of the rolled Cu-1.5%Ti alloy layers increased incessantly with increase in the number of rolling passes. Tensile strength increased up to 294 MPa which was about 1.54 times higher than that of the cast Cu-1.5%Ti alloy. Fracture surfaces of the rolled Cu-1.5%Ti alloy revealed the dimples in the structure, which is an indication of ductile fracture. © 2018 Author(s).
  • No Thumbnail Available
    Item
    Development, Characterization, Mechanical and Corrosion Behaviour Investigation of Multi-direction Forged Mg–Zn Alloy
    (Springer International Publishing, 2019) Anne, G.; Ramesh, S.; Kumar, G.; Sahu, S.; Ramesh, M.R.; Shivananda Nayaka, H.; Arya, S.
    In the present study, homogenized Mg−4%Zn (wt%) alloy was exposed to multi-direction forging (MDF) at 280 °C up to 5 passes successfully. Microstructural evolution, mechanical properties and corrosion behavior of the MDF-processed Mg−4%Zn alloy was investigated using different characterization techniques. Five passes of MDF (cumulative strain, ΣΔε = 3.45) led to the formation of ultrafine grain structure (grain size ~2.3 μm) with high angle grain boundaries (HAGBs) and high dislocation density. Corresponding ultimate tensile strength (UTS) and microhardness were observed to be 228 MPa and 88 Hv. Potentiodynamic polarization test results exhibited higher corrosion resistance (0.38 mm/y) in comparison with that of homogenized condition (1.33 mm/y). © 2019, The Minerals, Metals & Materials Society.
  • No Thumbnail Available
    Item
    Microstructural and mechanical characterisation of Al-Zn-Mg-Cu alloy processed by multi-directional cryo-forging
    (Elsevier Ltd, 2021) Ramesh, S.; Anne, G.; Naik, G.M.; Jagadeesh, C.; Shivananda Nayaka, H.S.
    Aim of the present investigation is to study the microstructural and mechanical properties of Al-Zn-Mg-Cu alloy before and after multi-direction forging (MDF) at cryogenic condition up to 3 cycles. Microstructure evolution of specimen was examined using optical microscope and orientation imaging microscopy as well as X-ray diffraction. Mechanical properties were measured by tensile test and Vickers micro hardness. Microstructural investigation shows that after 3 cycle of MDF average grain size was reduced to 8 μm with low angle grain boundaries (LAGBs) and high dislocation density. Mechanical examination displays an improvement in hardness, yield strength and ultimate tensile strength is due to increases in grain boundaries and strain hardening effect. After 3 cycles of MDF process with cumulative strain ςΔϵ = 3.64 led to the formation of fine grain structure, and microhardness were observed to be 168 HV. © 2021 Elsevier Ltd. All rights reserved.