Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
6 results
Search Results
Item Thermal contact at solder/substrate interfaces during solidification(2009) Nyamannavar, S.; Prabhu, K.N.Heat flux transients at the solder/substrate interface during the solidification of Sn-37Pb and Sn-3.5Ag solder alloys against metallic substrates were estimated by the lumped heat capacitance model and the contact condition was assessed by scanning electronic microscopy (SEM). Copper substrates yielded maximum contact heat flux followed by brass and aluminium substrates. The SEM study in the solder/substrate interfacial region revealed the existence of a clear gap with the aluminium substrate. A conforming contact was obtained with copper and brass substrates. © 2009 Institute of Materials, Minerals and Mining.Item Investigation into creep behaviour of Sn-40%Pb alloy using impression creep method(2009) Udaya Prasanna, H.U.; Udupa, K.R.; Prabhu, K.N.The creep behaviour of Sn-40%Pb hypereutectic alloys cast in the molds made of different materials was investigated using impression creep technique in the temperature range from zero to 32 °C and under the punching stress of 50 MPa. The creep curves.ie, profiles of indentation depth against time are generated and steady state creep rates (SSCRs) are determined. Activation energy was calculated knowing creep rates at different temperature levels. Standard metallographic technique was used to determine the grain size of alloys which were poured into different molds. It was found that SSCR, at all the temperature levels of testing, is a function of grain size of the material. The activation energy being in the range of 10kJ/mol -12 kJ/mol, suggests that the probable creep mechanism is dislocation glide aided by vacancy diffusion. Results of the experiments are discussed.Item Wetting behaviour and evolution of microstructure of Sn-Ag-Zn solders on copper substrates with different surface textures(2010) Satyanarayan, S.; Prabhu, K.N.The effect of surface roughness on wetting behaviour and evolution of microstructure of two lead-free solders (Sn-2.625Ag-2.25Zn and Sn-1.75Ag-4.5Zn) on copper substrate was investigated. Both solders exhibited good wettability on copper substrates having rough surface and lower wettabilty on smooth surfaces. The contact angles of solders decreased linearly with increase in surface roughness of the substrate. The exponential power law, ?=exp(-K ?n), was used to model the relaxation behaviour of solders. A high intermetallic growth was observed at the interface particularly on copper substrates with rough surface texture. A thin continuous interface showing scallop intermetallic compounds (IMC) was obtained on smooth surfaces. With an increase in surface roughness, the IMC morphology changed from scallop shaped to needle type at the Sn-2.625Ag-2.25Zn solder/substrate interface and nodular to plate like IMCs for Sn-1.75Ag-4.5Zn solder matrix. Copyright © 2010 by ASTM International.Item Wetting behaviour and interfacial microstructure of Sn-Ag-Zn solder alloys on nickel coated aluminium substrates(2011) Satyanarayan, S.; Prabhu, K.N.Wetting behaviours of two lead free solders (Sn-2·625Ag- 2·25Zn and Sn-1·75Ag-4·5Zn) on nickel coated aluminium substrates were investigated. Sn-2·625Ag-2·25Zn exhibited better wettability compared to Sn-1·75Ag-4·5Zn solder. Contact angles of the solders increased with increasing roughness of the substrate. The Young-Dupre equation was used to evaluate the work of adhesion of solder on the substrate. Sn-2·625Ag-2·25Zn solder exhibited higher work of adhesion than Sn-1·75Ag-4·5Zn. A thin continuous layer of Ni 3Sn was detected at the interface between Sn-2·625Ag- 2·25Zn solder and nickel coated Al substrate. Sn-1·75Ag- 4·5Zn solder exhibited scallop intermetallic compounds (IMCs) growing into the solder field as well as a thin continuous IMC in some cases. Ni 3Sn and Ni3Sn4 IMCs were observed at the interface of Sn-1·75Ag-4·5Zn solder and nickel coated Al. © 2011 Institute of Materials, Minerals and Mining.Item Effect of temperature and substrate surface texture on wettability and morphology of IMCs between Sn-0.7Cu solder alloy and copper substrate(2012) Satyanarayan, S.; Prabhu, K.N.In the present work, the effect of soldering temperature (270 and 298 °C) and substrate surface texture (0.02 and 1.12 ?m) on wetting characteristics and morphology of intermetallic compounds (IMCs) between Sn-0.7Cu lead-free solder on copper substrates was investigated. It was found that increase in temperature and substrate surface roughness improved the wettability of solder alloy. However, the effect of surface roughness on wettability was significant as compared to that of temperature. The spreading of solder alloy was uniform on smooth substrate, whereas spreading of the alloy on rough substrate resulted in an oval shape. The morphology of IMCs transformed from long needle shaped to short and thick protrusions of IMCs with increase in surface roughness of the substrate. Needle shaped and thick protruded intermetallics formed at the solder/Cu interface were identified as Cu 6Sn 5 compounds. The formation of Cu 3Sn IMC was observed only for the spreading of solder alloy at 298 °C which contributed to improvement in the wettability of solder alloy on both smooth and rough substrate surfaces. © Springer Science+Business Media, LLC 2012.Item The Effect of Wetting Gravity Regime on Shear Strength of SAC and Sn-Pb Solder Lap Joints(Springer New York LLC barbara.b.bertram@gsk.com, 2017) Sona, M.; Prabhu, K.N.The failure of solder joints due to imposed stresses in an electronic assembly is governed by shear bond strength. In the present study, the effect of wetting gravity regime on single-lap shear strength of Sn-0.3Ag-0.7Cu and Sn-2.5Ag-0.5Cu solder alloys reflowed between bare copper substrates as well as Ni-coated Cu substrates was investigated. Samples were reflowed for 10 s, Tgz (time corresponding to the end of gravity regime) and 100 s individually and tested for single-lap shear strength. The single-lap shear test was also carried out on eutectic Sn-Pb/Cu- and Sn-Pb/Ni-coated Cu specimens to compare the shear strength values obtained with those of lead-free alloys. The eutectic Sn-Pb showed significantly higher ultimate shear strength on bare Cu substrates when compared to Sn-Ag-Cu alloys. However, SAC alloys reflowed on nickel-coated copper substrate exhibited higher shear strength when compared to eutectic Sn-Pb/Ni-coated Cu specimens. All the substrate/solder/substrate lap joint specimens that were reflowed for the time corresponding to the end of gravity regime exhibited maximum ultimate shear strength. © 2017, ASM International.