1. Ph.D Theses
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/1/11
Browse
8 results
Search Results
Item Thermal Depolymerization of Scrap Tires Into Liquid Fuels: Upgradation and Utilization In Diesel Engine(National Institute of Technology Karnataka, Surathkal, 2022) Mohan, Akhil; Madav, Vasudeva; Dutta, SaikatConversion of scrap tire into fuel oils has attracted commercial attention since revenue can be generated from inexpensive and abundant feedstock while easing waste management issues. Globally, 1.5 billion scrap tires are generated every year. Environmental accumulation of tire waste is a global problem, and one way to control the problem is to convert them into fuels and specialty chemicals. There are various approaches for recycling scrap tires, such as re-treading, reclaiming useful products for playgrounds, open incineration, pyrolysis, gasification, and illegal dumping. Illegal dumping often provides a site for breeding mosquitoes, rodents, and larvae formation. Open burning releases a thick black plume of smoke with 1,3-butadiene, nitrogen, carbon, and sulfur oxides with the release of hazardous polyaromatic hydrocarbons. Out of the approaches mentioned above to recycle tires, pyrolysis is an interesting energy recovery process due to the formation of solid (carbon black) and steel wires (in the case of the tire), pyro-gas, along oil products. Production of crude tire pyrolysis oil from scrap tires is a promising approach by thermal depolymerization at an oxygen starved atmosphere and a temperature of 400-600 oC. The primary objective of present study is to refine CTPO by the principle of selective adsorption and preferential solubility using cost-effective adsorbent and solvent and utilization as a fuel in a single-cylinder diesel engine. A field study was conducted in a 10-ton rotating autoclave reactor to optimize scrap tire pyrolysis parameters (400 oC, 10 oC/min, 0.2 bar, 4 rpm), and investigate the existing problems in the industry with a special focus on applying CTPO in diesel engines. Crude tire pyrolysis oil (CTPO) is a dark brown to black colored syrupy liquid with C6-C24 organic compounds with various classes such as paraffin, olefins, terpenes, aromatics, nitrogen, and sulfur-containing compounds, oxygen-containing compounds. The major challenge for utilizing CTPO in engine or furnace is the inferior fuel properties such as low heat content, low flash point, high acidity, low cetane index, creaming or phase separation in storage tanks, pungent smell due to the presence of dibenzothiophenes and mercaptans. However, thermal distillation is widely used as an upgradation technology implemented in most of the small scale tire pyrolysis units. Distillation needs huge capital investment and energy, making the process less attractive and unsuitable for the long-term run. In the present study, a straightforward, robust, inexpensive, and scalable up-gradation strategy for refining CTPO by preferential solubility and selective adsorption to utilize single-cylinder direct-injected stationary engines is formulated. A limited study has been attempted for the up- gradation of CTPO using adsorbents and solvents. The present study also envisages extensive characterization of CTPO, StTPO and diesel to comprehend the fuel chemistry in terms of physical, thermal, and chemical analysis through various analytical techniques. GC×GC TOF- MS analysis showed that sulfur, benzene derivatives, naphthalene’s and polyaromatic hydrocarbons were lowered by 48.86%, 25.68%, 43.69%, and 27.79%, respectively. The batch scale process's oil yield is improved by 95% compared to the laboratory scale upgradation strategy. Experimental results found that StTPO40 is a binary optimal blend in terms of performance, combustion, and emissions. The emissions from StTPOxx were significantly improved after upgradation by silica gel as adsorbent and petroleum ether as a diluent. Furthermore, ethyl levulinate, a potential bio-diluent with high oxygenate, was also utilized as an additive to StTPOxx blends to scrutinize performance, combustion, and emissions of single- cylinder, direct-injected stationary diesel engine, which is another novelty of the present study. The emission components are significantly dropped down after the upgradation of CTPO, but the performance was slightly lowered after the refining process. The nitrous oxide emission from StTPO40 and StTPO40EL10 was significantly reduced by 43.09% and 44.54%, respectively. Heat release from StTPOxx and StTPOxxEL10 were higher than diesel due to the high amount of polyaromatics hydrocarbons, naphthalenes, and benzene derivatives. StTPO40EL10 is a ternary optimal blend in terms of performance, combustion, and emission, with EL as a potential diesel additive. It can be concluded that the StTPOxx and StTPOxxEL10 can be fully utilized in a diesel engine without any modifications and operational failures. In short, the lower blend percentage of StTPO40EL10 and StTPO40 can be used as an alternative fuel for a single-cylinder direct- injected diesel engine. In contrast, the higher blend percentage (StTPO60EL10, StTPO80EL10, StTPO90EL10, StTPO60, StTPO80, and StTPO100) can be utilized in boilers, furnaces, burners and marine engines.Item Experimental Investigation of Effect 0f Hydrogen and Higher Alcohol Blends on Engine Characteristics of Crdi Diesel Engine(National Institute of Technology Karnataka, Surathkal, 2022) K, Santhosh; G. N., KumarThe depletion of fossil fuels had alarmed the researchers to search for new sustainable renewable fuels. Biofuels and hydrogen are the most promising sustainable and renewable alternatives to diesel fuel. In the present renewable energy world, alcohols are gaining prime importance due to their nature of production and fuel properties. The experiment was conducted in a CRDI CI engine test rig at a constant speed of 2000 rpm and the load is varied from 20% to 80% in step of 20%. The main aim of the present investigation is to study the effect of higher alcohol and hydrogen on combustion, performance, and emission characteristics of CRDI CI engine, and also the present investigation aims to reduce the NOX emission by adopting the EGR and SCR of NOX techniques. Initially, a comparative analysis of 1-Pentanol and 1-Hexanol is done on engine characteristics of CRDI CI engine at standard engine conditions to find the best higher alcohol. From the results, it is noted that 1-Hexanol performs well compare to 1-Pentanol and from the results, the 30H70D blend is chosen as an optimized blend for further study. With the use of an optimized 1-Hexanol blend, further improvement in engine characteristics is done by varying the injection time to 9 ̊BTDC and 15 ̊BTDC. Compared to standard (12 ̊BTDC) and late injection (9 ̊BTDC), advanced injection time (15 ̊BTDC) showed better combustion, performance, and emission characteristics. Both BTE and BSEC showed only 1.77% and 1.8% reduction at 15 ̊BTDC compared to pure diesel operation. The optimization of alcohol blend and injection time showed a positive impact on performance and emission. The CO emission was almost equal to pure diesel operation and NOX emission was still lower compared to diesel fuel operation. The 1-Hexanol blends showed lagging in combustion and performance compared to pure diesel operation. For further improvement in combustion and performance, enrichment of hydrogen fuel through an inlet manifold is adopted. From the experimental investigation, it was noted that 10 lpm of hydrogen enrichment is optimum and it gives better compatibility with 1-Hexanol blends. The enrichment of hydrogen reduces the ignition delay and improves the poor combustion, performance, and emission characteristics of the 1-Hexanol blend in the engine. The hydrogen enriched 1-Hexanol blend showed an increment of 4.9% of BTE at 80% load compared to 1-Hexanol/diesel alone. Exhaust gas recirculation is the in-cylinder strategy and SCR of NOX is an after-treatment technique to reduce the NOX emissions from the engine. These two methods are adopted in this investigation to reduce the NOX emission from the engine with the optimized hydrogen-enriched 1-Hexanol blend. Here 10% and 20% EGR rate and Pt-Pd SCR catalyst iv are used for the investigation. The 10% EGR rate and Pt-Pd SCR catalyst showed a positive effect on the reduction of NOX. The main intention of the present investigation was to study the compatibility of 1- Hexanol in a diesel engine without compromising in performance and emission characteristics of the CI engine. The present investigation was also intended to study the new combustion and emission control technologies, which can be co-developed with alternative fuels. Finding and securing a renewable alternative energy source for diesel fuel and providing a compatible technology to work with alternative fuels in the engine were also conscious efforts. The present investigation was also focused to create huge options in the production and supply of alternative fuels.Item Effect of High Temperature Biodiesel Injection In Compression Ignition Engines(National Institute of Technology Karnataka, Surathkal, 2022) Kodate, Shankar; Yadav, Ajay Kumar; G. N., KumarExtensive research is being done to produce and utilise a variety of renewable fuels to meet the growing global energy demand and combat many issues such as environmental pollution, high costs of fossil fuels, and dependence on foreign energy sources. The current research aimed to extract and characterize Vateria indica and Karanja biodiesels through the transesterification process. The use of extracted biodiesels in a diesel engine leads to lesser brake thermal efficiency (BTE) and increased brake specific energy consumption (BSEC) due to higher viscosity and lower calorific value of biodiesels. This problem of higher viscosity is resolved by fuel preheating before injecting into the engine cylinder. The current research aims to evaluate the engine performance, emission, and combustion characteristics of Karanja oil methyl ester (KOME) and Vateria indica methyl ester (VIME) biodiesels blended with diesel at elevated fuel inlet temperatures ranging from 35 °C to 95 °C. The tests are carried out using two different engines, mainly the conventional DI engine (low-pressure injection at 180 bar) and CRDI engine (high-pressure injection at 1000 bar). In the CRDI engine, the effects of fuel injection timings and exhaust gas recirculation (EGR) rates on the engine parameters are also investigated. Results are obtained in terms of brake thermal efficiency, brake specific energy consumption, in-cylinder pressure, heat release rate, exhaust emissions of carbon monoxide (CO), hydrocarbon (HC), nitrogen oxide (NOX), carbon dioxide (CO2), and smoke opacity. It is observed from the findings of both the engines that the preheating of blends decreases viscosity which enhances engine performance, lower CO, HC, and soot emissions with a slight increase in NOX emissions. It is found that advancing the injection timing to 15° bTDC in a CRDI engine improves engine performance and reduces CO, and HC emissions with an increase in NOX emission compared to standard injection timing of 12° bTDC and retarded injection timing of 9° bTDC. As the EGR rate increases, engine performance decreases, and exhaust emissions like CO and HC increase with a reduction in NOX emission.Item Experimental Studies on Magnetic Field Assisted Combustion of Hydrocarbon Fuels in a Multicylinder Spark Ignition Engine under Liquid Phase and Gas Phase Operation(National Institute of Technology Karnataka, Surathkal, 2021) Oommen, Libin P.; N, Kumar G.Global energy demand forecasts indicate a growing trend with the ever-rising population and technology that enriches our everyday lives. Ironically, the rise in energy demand is 1.52 per cent per annum relative to the 1.14 per cent growth in population. Fossil oil, being the basic engine of industrial revolution, now meets more than 80 percent of global energy demand. The fossil energy is majorly used in the transport field in Internal Combustion Engines. With the rising trend of individuals using private cars, this share is expected to increase even higher, putting a burden on the energy sources. The over reliance on fossil fuels is so high that in a few decades the fossil reserves are predicted to become exhausted. Studies indicate that the transport industry itself using internal combustion engines contributes to 45 percent of India's overall air pollution. The rapid population growth and increased use of private vehicles has accounted for the countrywide deterioration of air quality. The combustion of fossil fuels in motors leads to the release of harmful contaminants such as CO, HC, CO2, NOx and PM of which the percentage content is increasing every year. The transition to e-mobility is challenging and is dependent on path breaking technologies and renewable energy penetration. This is the reason that provokes us to focus our research on the efficient utilization of existing fossil fuel energy and to come up with technologies that improve the fuel economy as well as the emission levels of internal combustion engines. The present research experimentally investigates the effect of a physical pre-treatment technique of hydrocarbon fuels before combustion in I.C. Engines using high intensity magnetic fields. The performance, combustion and emission characteristics of the engine under varying intensities of uniform magnetic fields created by high grade (N38) NdFeB are studied at four different loads (25%, 50%, 75% and 100%) and four different engine speeds (2000 rpm, 2500 rpm, 3000 rpm and 3500 rpm). The impact of magnetisation pattern on combustion parameters is analyzed by switching between two different patterns (axial and radial) of magnetisation exclusively. The influence of magnetic fields on liquid phase and gaseous phase combustion are analyzed separately by fuelling the iv engine with gasoline and LPG exclusively with the aid of suitable engine modifications. The effect of a post combustion treatment technique like part cooled exhaust gas recirculation is studied to come up with an optimal flow rate which benefits the combustion and emission of both liquid and gaseous phase fuels and is integrated with the optimal parameters in magnetic field assisted combustion to investigate the synergetic effect produced on the combustion of gasoline as well as liquefied petroleum gas. The experiments are conducted on a 10L inline Maruthi Suzuki Zen MPFI spark ignition engine which has modified provisions to operate on neat LPG. A separate gas ECU is provided for the switching between fuel phases. The input given to the gas ECU is the opening signal pulse from the already deployed gasoline ECU which is then modified with a correction factor before being sent to the gas injectors. Four distinct gas injectors are provided in the inlet manifold adjacent to the inlet port of individual cylinders for injecting LPG. These gas injectors are maneuvered by solenoid valves driven by 12V DC supply. The specifications of the gas injectors like nozzle diameter are designed corresponding to power generated per cylinder. Correspondingly injectors of nozzle diameter 1.75 mm is chosen for the given test engine. The NdFeB magnets of a particular magnetisation pattern are mounted on the fuel line with a non magnetic stainless steel covering adjacent to the fuel injector. A system for recirculating partially cooled exhaust gases into the combustion zone is designed for our experimentation. Prior to the data acquisition, the engine is operated for some time to reach steady state operation. Experimental error is minimized by taking average value of three readings at each test points. Initially experiments are conducted to study the performance, combustion and emission characteristics of the engine with axial magnetic fields applied on liquid phase hydrocarbons at various load and speed conditions. In the subsequent stages, the engine is fueled by gas phase hydrocarbons and then the axial fields are replaced using radial fields on both fuel phases. In the next part of investigation, the effect of locus of magnetisation is studied with respect to a single fuel phase. The optimal flow rate of part cooled EGR is v experimentally estimated for both fuel phases which is then integrated with the initially optimized parameters of magnetic fields and experimented in the final phase. Experimental results show that the effect of magnetic field assisted combustion is much more pronounced in the case of liquid phase hydrocarbons, owing to the continuous arrangement of hydrocarbon molecules in the liquid phase. Radial magnetisation pattern is observed to be more effective in molecular restructuring in both the fuel phases because of its ability to ionize the molecules in all directions. Magnetic field assisted combustion proves to be beneficial in improving the fuel economy and thermal efficiency of the engine under both fuel phases. Experimental results also indicate that recirculation of partially cooled exhaust gases are beneficial in enhancing the combustion and emission characteristics of the engine up to an optimum limit and are particularly useful in the reduction of oxides of nitrogen which in the normal case is enormous in LPG combustion. The synergetic effect of both these techniques is especially beneficial in terms of fuel economy, thermal efficiency and NOx emissions of the engine under both phases of hydrocarbons.Item Studies on The Performance, Combustion & Emission Characteristics of A Multicylinder Si Engine Fueled with lpg Along with Varying Steam Induction Rates(National Institute of Technology Karnataka, Surathkal, 2013) K. S, Shankar; Mohanan, PVehicle and fuel technologies have undergone important developments in the last 30 years. The volatility of oil prices and increasing concerns about the environment has influenced researchers to look in to possible alternatives to petroleum based fuels. Efforts are on to improve the combustion efficiency of the engines operating with conventional fuels. The various alternative fuels for spark ignition (SI) engines on which research is going on at present includes alcohols, liquefied petroleum gas (LPG), natural gas etc. Ethanol enriched gasoline blends are increasingly being used in SI engines due to the renewable nature of ethanol as well as increased governmental regulatory mandates. Ethanol can be produced from natural products or waste materials, compared with gasoline which is produced from non-renewable natural sources. In addition, ethanol shows good antiknock characteristics. Gaseous fuels are promising alternative fuels due to their economical costs, high octane numbers, higher heating values and lower polluting exhaust emissions. From the point of view of reduction of exhaust emissions such as unburnt hydrocarbon (HC) and carbon monoxide (CO), liquefied petroleum gas (LPG) is a useful alternative fuel for SI engines. Due to its higher octane value, LPG fuel can be used under the higher compression ratios. Combustion of LPG results in greater emissions of the oxides of nitrogen (NOX) than that for gasoline, the values reaching more than double at some operating conditions. Injection of water into the intake manifold has been found to be an effective way to reduce NOX emission in SI, CI and LPG engines. The present study deals with experimental investigations on the effect of steam induction with the intake air while using LPG as fuel on engine performance, combustion and emissions in a modified multi-cylinder SI engine. The engine operating parameters of speed, throttle opening positions and static ignition timings are varied. To compare the results of the above experiments, an ethanol enriched gasoline blend is optimized as a baseline fuel based on engine performance, combustion and emissions. The experimental setup consists of a stationary, fourstroke, four cylinder, multipoint port fuel injection (MPFI) engine of 44 kW capacity at 6000 rpm, which is connected to an eddy current dynamometer for loading. A piezo-electric pressure transducer is used for recording the cylinder pressure. The setup has a stand-alone panel box consisting of air box, fuel tank, manometer, fuel measuring unit, differential pressure transmitters for air and fuel flow measurements, process indicator and engine indicator. An AVL Digas 444 five gas Exhaust gas analyzer is used to measure the NOX (ppm), CO (%vol.), CO2 (%vol.) and HC (ppm) emissions in the exhaust. Initially experiments are conducted to study the performance, combustion and emission characteristics of the test engine fueled with ethanol enriched gasoline blends viz: E5, E10, E15 and E20 (on volume basis, and E5 means 5% ethanol and 95% gasoline) to optimize a baseline fuel. In the next part tests are conducted on the engine modified to run with injection of LPG as fuel and the combustion, performance and emission characteristics are evaluated. Separate four gas injectors are installed in the inlet manifold near the inlet port of each cylinder for injecting LPG. The gas injectors are operated by solenoid valves driven by 12V DC power supply. A separate gas ECU has been used for driving the solenoid valves. Experiments are conducted at wide open throttle (WOT) and part throttle conditions with varying loads in the engine speed range of 2000 rpm to 4500 rpm. Tests with ethanol enriched gasoline are conducted at the pre-set static ignition timing of 5 degree before top dead center (bTDC). The LPG performance and emissions are evaluated at various static ignition timings of 3, 4, 5 and 6 deg. bDTC. In the last part of the investigations, the engine tests are conducted with LPG along with steam induction. The waste heat from the exhaust gas has been used to generate steam from deionized water. Steam to LPG flow rates of 10, 15, 20 and 25% (on mass basis) are used. The steam is mixed with the intake air in the intake manifold of the engine. Results of the experiments have shown that among the various ethanol enriched blends, the blend of 20% ethanol was the most suitable one from the engine performance and CO & HC emissions points of view. At WOT operations the effect of ethanol blending on coefficient of variation of IMEP is to reduce it by an average of 2% with E15 fuel blend when compared to gasoline fuel operation over the entire speed range. All the ethanol-gasoline blends exhibit better cyclic variation pattern compared to gasoline at WOT operation. The engine performance has improved with the addition of ethanol, increasing the thermal efficiency and reducing the brakespecific energy consumption. A significant reduction in the HC emission was observed as a result of leaning effect and additional fuel oxygen caused by the ethanol addition. CO emission is reduced by addition of ethanol to gasoline. All engine exhaust emissions were lower at 3500-4000 rpm at various throttle valve opening condition except NOX which has shown an increasing trend with ethanol blended fuel. Hence it can be concluded that blending ethanol up to 20% to gasoline will reduce the cycle-by-cycle combustion variations and emissions though a marginal increase in NOX emissions results. The findings of the experiments with LPG suggest that higher thermal efficiency and therefore improved fuel economy can be obtained from SI engines running on LPG as against gasoline at the pre-set static ignition timing of 5 deg. bTDC. Also the exhaust emissions of CO, HC have reduced considerably. But the emissions of NOX have increased significantly at higher engine speeds. The CO emission has reduced from an average value of 5 % to about 1.3 % and corresponding change in HC noticed was from 350 ppm to 22 ppm when LPG was used instead of gasoline at pre-set static ignition timing. The NOX emission with LPG was almost double when compared to that with gasoline at higher engine speeds. When engine runs with LPG, better performance has been observed when static ignition timing is advanced to 6 deg. bTDC. Advancing the static ignition timing has also resulted in reduced CO and HC emissions. But the advanced ignition timing shows a further increase in NOX emissions. Retarding the ignition timing achieves lesser NOX emissions at higher engine speeds. Steam induction is one of the methods to reduce NOX emissions. Steam induction will reduce the peak temperature of the engine cylinder so that NOX formation will be reduced. The experimental results showed that steam induction worked as a cooling means for the fuel-air charge and slowing the burning rates, resulting in reduction of the peak combustion temperature. It is found that NOX emissions have reduced significantly by 20 - 45% over the entire operating range when compared to LPG operation. No considerable changes in CO and HC emissions are observed. Hence use of LPG with advanced ignition timing of 6deg. bTDC with steam induction up to 25% steam to fuel mass ratio at higher engine speeds and up to 10% steam to fuel massratio at lower engine speeds can be used from the point of view of improved engine performance and reduced exhaust emissions. When comparing the performance and emissions of ethanol enriched gasoline and LPG with steam induction, it is noted that, comparatively E20 blends performs better that LPG alone. With steam induction the performance with LPG deteriorates. The brake thermal efficiency of 15% steam with LPG at wide open throttle condition and 3500 rpm is lower by 3.5% when compared to E20. CO reduces with LPG when compared to E20. But a slight increment is noted when steam is inducted. NOX emissions are higher for both E20 and LPG when compared to gasoline. However, with the induction of steam along with LPG, the NOX can be substantially brought down. At 3500 rpm and wide open throttle condition, the NOX emissions of E20 and 15% steam with LPG are similar. But at 4500 rpm, NOX emission is higher by 580 ppm. From the experimental investigations it can be concluded that use of ethanol enriched blends in unmodified engine is an alternative for the use of gasoline as a sole fuel. However with the current option of LPG as alternative fuel to SI engines, it can be used along with steam induction as a means to considerably reduce NOX emissions, with marginal reduction in engine performanceItem Suitability of Biofuels and Plastic Oil Blended With Diesel in CRDI Engine(National Institute of Technology Karnataka, Surathkal, 2017) Lamani, Venkatesh T.; Yadav, Ajay Kumar; Kumar, G. N.Nitrogen oxides and smoke are the substantial emissions for the diesel engines. Fuels comprising high-level oxygen content can have low smoke emission and higher efficiency due to better combustion. The objective of this research is to assess the potential to employ oxygenated fuels such as dimethyl ether, ethanol and butanol, and waste plastic oil in direct injection engine as alternative fuels for diesel. To reduce NOX, exhaust gas recirculation technology for various fuels is studied. Computational fluid dynamics (CFD) studies on combustion and emission characteristics of common rail direct injection (CRDI) engines using oxygenated fuel-diesel blends are less developed and still under intense study. In view of that detailed CFD simulation is carried out in present study and also validated with experimental results. Ethers are favourable alternative for diesel engine due to their chemical structure. Presence of more oxygen, absence of carbon-carbon (C-C) bond in chemical structure, and high cetane number of dimethyl ether (DME), cause less pollution in DME operated engine compared to diesel engine. Study emphasizes the effect of various EGR rates (0-20%) and DME-diesel blends (0-20%) on combustion characteristics and exhaust emissions of CRDI engine using CFD simulation. Results show that, due to better combustion characteristics of DME, indicated thermal efficiency (ITE) increases with the increase in DME- diesel blends. Ethanol is an attractive alternative fuel because it is oxygenated, renewable and bio-based resource; thereby it has potential to reduce smoke emissions in compression-ignition engines. CFD simulation is carried out to study the effect of EGR and injection timing on the performance, combustion and exhaust emission characteristics of CRDI engine fuelled with bioethanol-diesel blends. The results indicate that the mean CO formation and ignition delay increase whereas mean NOX formation and in-cylinder temperature decrease with increase in the EGR rate. Further, CFD simulation is carried out to find optimum injection timing for bioethanol-diesel blends (0-30% ethanol). Optimum injection timing is obtained for maximum ITE. Obtained CFD results are validated with experimental data available in literature and found good agreements.Several second generation biofuels (e.g., n-butanol) are also promising alternative to diesel fuel. The experimental and CFD simulation is carried out to estimate the performance, combustion and exhaust emission characteristics of n-butanol-diesel blends (0 to 30%) for various injection timings and various EGR rates using modern twin-cylinder, four-stroke, CRDI engine. Experimental results reveal the increase in brake thermal efficiency (BTE) for n-butanol-diesel blends. Attention is also focused to counter plastic waste disposal problem and to find alternate fuel to diesel by waste to energy retrieval. Present range of investigation evaluates the prospective use of waste plastic oil (WPO) as an alternative fuel for diesel engine. Experiments are conducted for various injection timings and for different EGR rates. Combustion, performance and tail pipe emissions of CRDI engine are studied. The NOx, CO and soot emissions for waste plastic oil-diesel blends are found more than neat diesel. To reduce NOx, EGR is employed which results in reduction of NOx considerably. Brake thermal efficiency (BTE) of blends is found to be higher compared to diesel. The higher NOx emitted by engine operated with WPO-Diesel blends are treated by multiple injection strategies. Experiments are carried out for various pilot injection timings and different main injection timings. The remarkable reduction in nitrogen oxide is observed by retarding main injection timing and injecting more fuel in pilot injection compared to single injection.Item Performance and Emission Characteristics of a Multi-Cylinder Si Engine on Gasoline-Lpg Dual Fuel Mode of Operation(National Institute of Technology Karnataka, Surathkal, 2017) Nayak, Vighnesha; Mohanan, P.Population growth over the last decades has led to tremendous growth in fossil energy demand with increased industrialization and use of vehicles. The most common fuel for internal combustion engines is still made out of oil, but continuous increases in oil prices has increased interest in alternative fuels. Strict international regulations on emissions and improving the combustion efficiency, gaseous fuels found to be better alternative fuel for conventional fuel. Gaseous fuels are promising alternative fuels due to their economic costs, high octane numbers, higher heating values and lower polluting exhaust emissions. LPG, as a relatively clean fuel, is considered one of the most promising alternative automotive fuels because of its emission reduction potential and lower price than gasoline. Turbocharger plays vital role in enhancing the boost pressure of IC engines. Turbocharging the engine will improve the combustion characteristics and reduces the NOX emission. Dilution of intake charge is the one of the method to reduce NOX emission. Vaporised watermethanol induction is used to reduce the emissions from the engine. The present study deals with experimental investigations of LPG-gasoline dual fuel mode of operation on engine performance, combustion and emission characteristics with turbocharging and vaporized water-methanol induction. A stationary four stroke, four cylinders, MPFI engine capable of developing 44 kW at 6000 rpm has been modified to operate on LPG fuel. A separate gas ECU has been developed with software to operate dual fuel mode of operation. The engine operating parameters of speed, load conditions and static ignition timings are varied. A turbocharger is selected based on the exhaust mass flow energy of the engine and installed in the experimental test rig with necessary modification in the intake and exhaust manifold. The waste heat from the exhaust gas has been used to generate vapor from water-methanol mixture and induced into the intake manifold to reduce the emissions from the engine. Initially experiments are conducted to study the performance, combustion, cycle by cycle variations and emission characteristics of the test engine fueled with different percentage of LPG by mass viz: 0%, 25%, 50%, 75% and 100%. In the next part of investigation, static ignition timings are advanced from 5 deg. bTDC to 8 deg.iv bTDC and 11 deg. bTDC to analyze performance and emission characteristics. During this stage percentage of LPG and static ignition timing are optimized based on performance and emission characteristics. Experiments are conducted at full load and part loads in the engine speed range of 2000 rpm to 4500 rpm. In third stage of research, a turbocharger is installed and conducted the experiment for optimized conditions. In the last part of the investigations, the engine tests are conducted with vaporized water-methanol induction. The waste heat from the exhaust gas has been used to generate vapor from deionized water-methanol mixture. Vapor to LPG flow rates of 10, 20 and 30% (on volume basis) are used. The vapor is mixed with the intake air in the intake manifold of the engine. From experimental investigation for dual fuel mode of operation at 5 deg. bTDC it is found that with the 50% usage of LPG, increases the brake thermal efficiency and volumetric efficiency when compared to gasoline for speed range of 2000 rpm to 4000 rpm. 100% LPG will have much lower CO and HC emissions when compared to gasoline. This is a positive effect on environment. But for other LPGgasoline ratio these emissions going to increases when compared to 100% LPG but it is well below when compared to gasoline for all speeds. NOX emission is more for 100% LPG almost 4 times that of gasoline for all speed conditions. For other LPGgasoline ratio NOX emission is lower. Combustion results revealed that as the LPG percentage increases the peak pressure also increases and it is maximum for 100% LPG for all the speed. This increase in peak pressure will indicate the LPG will give better combustion properties compared to that of gasoline. Compared to peak pressure, the variation in cycle to cycle for IMEP is less for 50% LPG at higher speed conditions. 50% LPG showed better cycle by cycle fluctuations when compared to other fuel conditions. Net heart release rate shows that gasoline will give the more heat release compare to all other fuels, but 100% LPG will release the heat little earlier than gasoline. Since peak pressure is near to TDC for 100% LPG which results in NHRR to occur earlier than gasoline. Final outcome of the research is 100% LPG will have better combustion properties compared to gasoline but cyclic fluctuations are more for 100% LPG.v Results have shown that advancing the static ignition timing will increase the BP by 12 % at 11 deg. bTDC and 7% at 8 deg. bTDC for gasoline. Whereas for 100% LPG increased in BP is 5 % at 11 deg. bTDC and 2% at 8 deg. bTDC. BTE also increased for both gasoline and LPG when advancing static ignition timing because of reduction in the fuel consumption. Also advancing the ignition timing will engine will work leaner side hence reduction in the fuel consumption. From the results it is revealed that as the static ignition timing is advanced volumetric efficiency is increases for gasoline and 100% LPG. For other fuel conditions there is not much effect of static ignition timing on volumetric efficiency. CO emission will drastically reduce when static ignition timing advanced to 8 deg. bTDC after that not significant reduction in CO emission. 100% LPG shown major reduction in CO emission is obtained while advancing the static ignition timing. But advancing the Static ignition timing resulted in increased HC emission for all fuel blends. NOX emission also increases with advancing the static ignition timing for all fuel blends because of increase in the incylinder temperature. Finally after varying the static ignition timing it is found that 8 deg. bTDC with 100% LPG will resulted in better performance and emission characteristics hence these conditions are optimized for the further research work. Using turbocharger performance characteristics are improved. For 100% LPG and gasoline with turbocharger BP and BTE is increased when compared to without turbocharger. BTE obtained is maximum at 8 deg. bTDC with turbocharger for 100% LPG when compared to all other condition. Turbocharged engine fuelled with LPG has higher volumetric efficiency as compared to engine without turbocharger for all speed and load conditions. Volumetric efficiency increases for turbocharged engine because of higher intake air pressure will increase the density of air which leads to increase in the efficiency. When compared to base fuel gasoline at 5 deg. bTDC average increase in volumetric efficiency for 100% LPG with turbocharger is 13% at same condition. Emissions are greatly reduced with turbocharger with 100% LPG when compared to gasoline with turbocharger. When compared to base fuel gasoline at 5 deg. bTDC average decrease in CO emission for LPG with turbocharger is 72% at same condition. There is no much variations in HC emission when compared LPG with and without turbocharger at full load conditions. The turbocharged engine fuelled with LPG, there will be a good decrease in NOX for all load conditions. This is because turbochargervi will increase the charge density hence mixture becomes to lean in the combustion zone hence formation of NOX will reduces for all load conditions. In-cylinder pressure and net heat release rate (NHRR) also greatly improved with usage of turbocharger. Maximum of 17 bar increase in the in-cylinder pressure is obtained with usage of turbocharger. Turbocharged engine gave great improvement in cycle by cycle fluctuations when compared to naturally aspirated engine. Maximum of 84% reduction in COV of IMEP is obtained for turbocharged LPG fuel. Turbocharger will give the better combustion, performance and emission characteristics for LPG fuel. From the experimental results for deionized water-methanol induction system it is observed that as the percentage of water-methanol increases, the engine brake thermal efficiency increased for part and full load conditions. Further increase in the flow rate of water-methanol beyond 30% will reduce the brake thermal efficiency drastically. Also results show that water-methanol induction will results in reduction of brake specific energy consumption (BSEC). Water-methanol induction has good effects in decreasing NOX emission significantly. At full load condition around 30% and 40% average reduction in NOX emission are obtained for 20% and 30% watermethanol flow rate. HC and CO emissions are going to reduce slightly with watermethanol induction due to presence of more oxygen in the charge to the engine. It can be seen that use of 50% LPG is superior alternative for unmodified multi-cylinder SI engine for better engine performance and emission characteristics. The use of 100% LPG is best suited for SI engines at 8 deg. bTDC advance static ignition timing with turbocharging and 20%vaporized water-methanol induction rate to get enhanced engine performance and emission characteristics.Item Combustion Control and Performance Analysis of CI Modified HCCI Engine Using Lean Combustion Technology(National Institute of Technology Karnataka, Surathkal, 2018) M. R, Sumanlal; Mohanan, P.Amongst the numerous research papers published over the last decade, the homogenous charge compression ignition (HCCI) has often been considered as a new combustion process in reciprocating internal combustion engines. With increasingly stringent emission legislation and demand for significant reduction in CO2 emission, research and development of cleaner and more efficient combustion engines has been intensified. HCCI combustion has emerged as an effective and viable technology that has the potential of simultaneously reducing pollutant emissions and fuel consumption from internal combustion engines. The investigation focuses on the effect of diesel vapour induction on the engine performance and to try and achieve Homogeneous Charge Compression Ignition (HCCI) mode of combustion in the engine. An existing direct injection CI engine is modified to work as an HCCI engine by using a shell and tube heat exchanger which aids in the production of diesel vapour by utilising heat content of exhaust gases . The external mixture formation is adopted for the preparation of homogenous charge. The diesel vapour coming out of the heat exchanger is mixed with air near the intake manifold. The experimental set up is modified so that the flow of exhaust gas to the heat exchanger and the flow of diesel vapour to the engine can be controlled. A separate fuel tank is provided to measure the amount of diesel vapour utilized. Vapour utilization studies were carried out. It is found that a maximum utilization was limited to 60 percentage at different load conditions. After that knocking occurs and engine stops working. The loading of HCCI mode was limited from 50 to 100 % due to poor vapour quality at lower loads. The performance and emission characteristics of HCCI engine is studied at different injection pressures and injection timings and is compared with conventional engine. It is found that a higher injection pressure of 200 bar and advancing the injection timing to 31.50 bTDC improved the brake thermal efficiency of the engine and reduced NOx emissions with increase in Hydrocarbon and Carbon Monoxide emissions. A maximum of 20.54 % increase in brake thermal efficiency is obtained at 75 % load condition. NOx emissionsare reduced upto a maximum of around 50% at 31.5 deg. bTDC, 200 bar injection pressure and in vapour induction by 37% whereas CO emissions are increased around 31% and HC emissions are increased by 47%. Normally Research engines are fitted with piezoelectric pressure transducer for the measurement of in cylinder pressure. But strong ion concentration is formed in the cylinder by the combustion process. If the ion concentration is detected, it can be used as a combustion diagnosis tool. Here a standard spark plug is converted to work as the ion sensor. It is carefully mounted over the cylinder head without affecting the passage of cooling water. An electrical circuit is designed to measure the ion voltage produced during the combustion process. Then a correlation between ion voltage and cylinder pressure is developed from the measured data so that ion voltage is calibrated in to in cylinder pressure. The results show that there is only 10% difference between the pressure given by the pressure sensor and ion sensor. Therefore the expensive pressure transducer is replaced by cheap and reliable ion sensor for combustion monitoring. Extending the operation range in HCCI mode is a very important factor. For every load condition the amount vapour inducted to the engine is limited. Preheating of intake charge reduces the possibility of condensation of diesel vapour near intake manifold. Therefore the effect of preheating was also studied by heating the inlet air by using a heating coil. Preheating always improved the percentage vapour utilization. A percentage increase of 5.91 %, 7.93 % and 7.3 % in percentage vapour utilization is found for 50 %, 75 % and 100 % load conditions respectively. Preheating improved the brake thermal efficiency and brought down CO and HC emissions however it slightly increased NOx emissions. The maximum efficiency is 33. 5% seen at 75% load condition for preheating temperature of 65 °C and at percentage vapour utilization of 37.95 %. A maximum percentage reduction of 78.33 %, 45.15 % and 57.14 % in CO emissions was attained by preheating of air at 50, 75 and 100 % load conditions respectively. A maximum percentage decrease of 48.3 %, 50 % and 44.82 % in Unburned Hydrocarbon emissions was attained by preheating for 50, 75 and 100 % load conditions respectively. NOx emissions are increased by almost 5% for different load conditions by preheating of theintake air. Preheating of vapour was limited to 65 °C due to continuous increase in NOx emissions. Thus the most suitable operating condition for HCCI mode can be identified as 75 % load coupled with 65 °C preheating. The increase in vapor mass fraction increased the performance of the engine. This was mainly because the HCCI mode of combustion was approached. At the same time the start of combustion was still governed by the injection of vapor fuel. This gave a method of control of combustion which is normally difficult in HCCI engines