Browsing by Author Kadoli, R.

Jump to: 0-9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
or enter first few letters:  
Showing results 1 to 20 of 37  next >
Issue DateTitleAuthor(s)Supervisor(s)
2006Buckling and free vibration analysis of functionally graded cylindrical shells subjected to a temperature-specified boundary conditionKadoli, R.; Ganesan, N.-
2010Comparative analysis of steady state heat transfer in a TBC and functionally graded air cooled gas turbine bladeCoomar, N.; Kadoli, R.-
2016Computational design of mould sprue for injection moulding thermoplasticsLakkanna, M.; Mohankumar, G.C.; Kadoli, R.-
2015Criticality of appreciating non-newtonianivity in plastic injection mould conduit designLakkanna, M.; Kadoli, R.; Mohankumar, G.C.-
2013Design and study of magnetization characteristics of a magnetostrictive (Tb0.3Dy0.7Fe1.95) actuator under zero pre-stress conditions for direct current inputJoshi, R.; Kadoli, R.-
2013Design of sprue bush for a plastic injection mould: A machine perspectiveLakkanna, M.; Kadoli, R.; Mohankumar, G.C.-
2016Dry Sliding Wear Behavior of Super Duplex Stainless Steel AISI 2507: A Statistical ApproachDavanageri, M.; Narendranath, S.; Kadoli, R.-
2007Effect of boundary conditions and convection on thermally induced motion of beams subjected to internal heatingMalik, P.; Kadoli, R.; Ganesan, N.-
2017Effect of Sigma (?) phase on Mechanical and Dry sliding wearDavanageri, M.B.; Narendranath, S.; Kadoli, R.-
2013Effect of thermal treatment on the wear behavior of lean duplex stainless steel and super duplex stainless steelsNaveen, Kumar, R.; Davangeri, M.B.; Joshi, A.G.; Narendranath, S.; Kadoli, R.-
2017Evaluation of flow properties of air at the exit of holes on the blow pipe in a pulse jet filter bag houseThumbe, J.; Kadoli, R.; Gangadharan, K.V.-
2013Experimental and theoretical investigations on the cyclic operation of TSA cycle for air dehumidification using packed beds of silica gel particlesRamzy, A.K.; Kadoli, R.; Ashok, Babu, T.P.-
2018Experimental and theoretical study on dehumidification potential of clay-additives based CaCl2 composite desiccantsHiremath, C.R.; Kadoli, R.; Katti, V.V.-
2013Experimental studies on heat and mass transfer in a packed bed of burnt clay impregnated with CaCl2 liquid desiccant and exploring the use of gas side resistance modelHiremath, C.R.; Kadoli, R.-
2019Finite element and differential quadrature solution for natural frequency of a clamped-free pipe conveying fluidChandurkar, S.; Kadoli, R.-
2008Finite element formulation for passive shape control of thin composite plates with integrated piezoelectric layerKadoli, R.; Kendri, R.G.-
2013Finite element magnetostatic analysis of magnetostrictive (Tb 0.3Dy0.7Fe1.95) actuator with different housing materialsJoshi, R.; Subba, Rao, M.; Kadoli, R.-
2018Finite Element Wear Behaviour Modeling of Super duplex stainless steel AISI 2507 Using AnsysDavanageri, M.B.; Narendranath, S.; Kadoli, R.-
2016High temperature corrosion behaviour of HVOF sprayed WC-CrC-Ni coatingsSomasundaram, B.; Kadoli, R.; Ramesh, M.R.; Ramesh, C.S.-
2015Hot Corrosion Behaviour of HVOF Sprayed (Cr3C2 35 % NiCr) + 5 % Si Coatings in the Presence of Na2SO4 60 % V2O5 at 700 CSomasundaram, B.; Kadoli, R.; Ramesh, M.R.-