Browsing by Author Rao, S.S.

Jump to: 0-9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
or enter first few letters:  
Showing results 1 to 20 of 45  next >
Issue DateTitleAuthor(s)Supervisor(s)
2014Analysis of surface roughness and hardness in ball burnishing of titanium alloyRevankar, G.D.; Shetty, R.; Rao, S.S.; Gaitonde, V.N.-
2014Analysis of surface roughness and hardness in titanium alloy machining with polycrystalline diamond tool under different lubricating modesRevankar, G.D.; Shetty, R.; Rao, S.S.; Gaitonde, V.N.-
2017Application of particle swarm optimization and response surface methodology for machining parameters optimization of aluminium matrix composites in milling operationMalghan, R.L.; Rao, K.M.C.; Shettigar, A.K.; Rao, S.S.; D Souza, R.J.-
2019Assessment of influence of process parameters on properties of friction stir welded Al-Ce-Si-Mg aluminium alloyD'Souza, A.D.; Rao, S.S.; Herbert, M.A.-
2011Behavioral study of alumina nanoparticles in pool boiling heat transfer on a vertical surfaceHegde, R.N.; Reddy, R.P.; Rao, S.S.-
2012Boiling induced nanoparticle coating and its effect on pool boiling heat transfer on a vertical cylindrical surface using CuO nanofluidsHegde, R.N.; Rao, S.S.; Reddy, R.P.-
2010Critical heat flux enhancement in pool boiling using alumina nanofluidsHegde, R.; Rao, S.S.; Reddy, R.P.-
2009Determination of transient and steady state cutting in face milling operation using recurrence quantification analysisMhalsekar, S.D.; Mohan, G.; Rao, S.S.; Gangadharan, K.V.-
2010Development of a surface roughness prediction system for machining of hot chromium steel (AISI H11) based on artificial neural networkRai, R.; Kumar, A.; Rao, S.S.; Shriram-
2018Development of novel cutting tool with a micro-hole pattern on PCD insert in machining of titanium alloyRao, C.M.; Rao, S.S.; Herbert, M.A.-
2014Direct torque controlled induction motor drive based on cascaded three two-level invertersKumar, T.V.; Rao, S.S.-
2018Effect of process parameters in face milling operation and analysis of cutting force using indirect methodmalghan, R.L.; Rao, K.M.C.; ArunKumar, S.; Rao, S.S.; D Souza, R.J.-
2015Effect of Rotational Speeds on the Cast Tube During Vertical Centrifugal Casting Process on Appearance, Microstructure, and Hardness Behavior for Al-2Si AlloyShailesh, Rao, A.; Tattimani, M.S.; Rao, S.S.-
2019An Efficient Approach to Optimize Wear Behavior of Cryogenic Milling Process of SS316 Using Regression Analysis and Particle Swarm TechniquesKarthik, Rao, M.C.; Malghan, R.L.; ArunKumar, S.; Rao, S.S.; Herbert, M.A.-
2020An Experimental and Numerical Approach to Study the Performance of Modified Perforated Cutting Tools on Machining of Ti 6Al 4V AlloyRao, C.M.; Rao, S.S.; Herbert, M.A.-
2012Experimental studies on CHF enhancement in pool boiling with CuO-water nanofluidHegde, R.N.; Rao, S.S.; Reddy, R.P.-
2009Experimental studies on turning of discontinuously reinforced aluminium composites under dry, oil water emulsion and steam lubricated conditions using TAGUCHI's techniqueShetty, R.; Pai, R.; Rao, S.S.-
2011Experimental study on CuO nanoparticles in distilled water and its effect on heat transfer on a vertical surfaceHegde, R.N.; Rao, S.S.; Reddy, R.P.-
2017Experimental study on linear displacement measurement sensor using RGB color variation technique with PID controllerMurthy, A.; Rao, S.S.; Herbert, M.A.; Navin, Karanth, P.-
2012Flow visualization and study of critical heat flux enhancement in pool boiling with Al 2O 3-water nanofluidsHegde, N.R.; Rao, S.S.; Reddy, R.-