Browsing by Author Desai, V.

Jump to: 0-9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
or enter first few letters:  
Showing results 21 to 40 of 40 < previous 
Issue DateTitleAuthor(s)Supervisor(s)
2015Influence of combined grain refinement and modification on the Microstructure, tensile strength and wear properties of Al-15Si, Al-15Si-4.5Cu alloysChannappagoudar, S.; Sannayallappa, N.; Desai, V.; Karodi, V.-
2015The influence of the addition of 4.5 wt.% of copper on wear properties of Al-12Si eutectic alloyChannappagoudar, S.; Aithal, K.; Sannayallappa, N.; Desai, V.; Mukunda, P.G.-
2020Influence of Ti coated tools on process parameters in turning process of MDN431Badiger, P.V.; Desai, V.; Ramesh, M.R.; Vinyas, M.; Santhosh, C.M.; Prajwala, B.K.; Raveendra, L.-
2016An investigation on characteristics and free vibration analysis of laminated chopped glass fiber reinforced polyester resin compositeAllien, V.; Kumar, H.; Desai, V.-
2017An investigation on high temperature erosion behaviour of plasma sprayed CoCrALY/Al2O3/YSZ on fe and ni based alloysNithin, H.S.; Desai, V.; Ramesh, M.R.-
2011Machining characteristics of multiwall-CNT reinforced Al/Al-Si composites using recurrence quantification analysisGangadharan, K.V.; Umashankar, K.S.; Ravish; Desai, V.-
2011Machining characteristics of nanocompositesUmashankar, K.S.; Gangadharan, K.V.; Desai, V.; Shivamurthy, B.-
2010Modeling of single and multilayer polyvinylidene fluoride film for micro pump actuationKaranth, P.N.; Desai, V.; Kulkarni, S.M.-
2018Optimization of machining parameters in turning process of mdn431 using ti-multilayer coated toolBadiger, P.V.; Desai, V.; Ramesh, M.R.; Raveendra, K.-
2003Performance and emission studies on the effect of injection timing and diesel replacement on a 4-S LPG-Diesel Dual-Fuel EngineSudhir, C.V.; Desai, V.; Kumar, S.Y.; Mohanan, P.-
2018Performance of DLC coated tool during machining of MDN431 alloyed steelBadiger, P.V.; Desai, V.; Ramesh, M.R.-
2018Performance of Ti-multilayer coated tool during machining of MDN431 alloyed steelBadiger, P.V.; Desai, V.; Ramesh, M.R.-
2011Recurrence quantification analysis to compare the machinability of steelsRavish; Umashankar, K.S.; Alva, A.; Gangadharan, K.V.; Desai, V.-
2020Semi-active vibration control of MRF core PMC cantilever sandwich beams: Experimental studyAllien, J.V.; Kumar, H.; Desai, V.-
2019Semi-active vibration control of SiC-reinforced Al6082 metal matrix composite sandwich beam with magnetorheological fluid coreAllien, J.V.; Kumar, H.; Desai, V.-
2019Sintering metal injection molding parts of tungsten-based steel using microwave and conventional heating methodsVeeresh, Nayak, C.; Ramesh, M.R.; Desai, V.; Samanta, S.K.-
2003Studies on influence of injection timing and Diesel replacement on LPG-Diesel dual-fuel engineSudhir, C.V.; Desai, V.; Suresh, Kumar, Y.; Mohanan, P.-
2003Studies on influence of injection timing and diesel replacement on LPG-diesel dual-fuel engineSudhir, C.V.; Desai, V.; Suresh, Kumar, Y.; Mohanan, P.-
2015System identification for helicopter longitudinal dynamics model - Best practicesKamble, S.B.; Desai, V.; Jeppu, Y.V.; Prajna-
2019Tribological behaviour of monolayer and multilayer Ti-based thin solid films deposited on alloy steelBadiger, P.V.; Desai, V.; Ramesh, M.R.; Joladarashi, S.; Gourkar, H.-