1. IR@NITK

Browsing by Title

Jump to: 0-9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
or enter first few letters:  
Showing results 4848 to 4867 of 10116 < previous   next >
Issue DateTitleAuthor(s)Supervisor(s)
2016Influence of process parameters on material removal rate and surface roughness in WED-machining of Ti50Ni40Cu10 shape memory alloyManjaiah, M.; Narendranath, S.; Basavarajappa, S.; Gaitonde, V.N.-
2020Influence of process variables on joint attributes of friction stir welded aluminium matrix compositePrabhu R.S.B.; Shettigar A.K.; Patel GC M.; Herbert M.; Rao S.S.-
2020Influence of Rectangular Ribs on Exergetic Performance in a Triangular Duct Solar Air HeaterNidhul; Kottayat; Kumar; Sachin; Yadav; Ajay Kumar; Anish; S.-
2014Influence of redmud on the mechanical, damping and chemical resistance properties of banana/polyester hybrid compositesArumuga, prabu, V.; Uthayakumar, M.; Manikandan, V.; Rajini, N.; Jeyaraj, P.-
2019Influence of retrogression and re-ageing heat treatment on the fatigue crack growth behavior of 7010 aluminum alloyNandana, M.S.; Udaya, Bhat, K.; Manjunatha, C.M.-
2020Influence of Retrogression and Re-Aging Treatment on Microstructure, Mechanical and Fatigue Crack Growth Behavior of Aluminum Alloy 7010Nandana, M. S.K, Uday Bhat.; Manjunath, C. M.
2009Influence of rotational speed during centrifugal casting on sliding wear behaviour of the Al-2Si alloyMukunda, P.G.; Shailesh, Rao, A.; Rao, S.S.-
2010Influence of rotational speed of centrifugal casting process on appearance, microstructure, and sliding wear behaviour of Al-2Si cast alloyMukunda, P.G.; Rao, A, S.; Rao, S.S.-
2014Influence of Route-R on wrought magnesium AZ61 alloy mechanical properties through equal channel angular pressingAvvari, M.; Narendranath, S.-
2020Influence of sample preparation techniques on microstructure and nano-mechanical properties of steel-concrete interfaceGoudar S.K.; Das B.B.; Arya S.B.; Shivaprasad K.N.-
2019Influence of sic and al2o3 particulate reinforcement on the mechanical properties of za27 metal matrix compositesAnjan, B.N.; Preetham, Kumar, G.V.-
2013Influence of silica fume on the strength of betostyrene mixed concreteSambo, A.G.; Deepak, T.J.; Mithun, B.M.-
2021Influence of slide burnishing process on the surface characteristics of precipitation hardenable steelSachin B.; Rao C.M.; Naik G.M.; Puneet N.P.-
2014Influence of Sn doping on photoluminescence and photoelectrochemical properties of ZnO nanorod arraysKumar, A.S.; Huang, N.M.; Nagaraja, H.S.-
2017Influence of spark timing on the performance and emission characteristics of gasoline hydrogen-blended high-speed spark-ignition engineShivaprasad, K.V.; Chitragar, P.R.; Nayak, V.; Kumar, G.N.-
2013Influence of substrate temperature and post deposition annealing on the properties of vacuum deposited ZnSe thin filmsGowrish, Rao, K.; Bangera, K.V.; Shivakumar, G.K.-
2015Influence of sulfate ion concentration and pH on the corrosion of Mg-Al-Zn-Mn (GA9) magnesium alloyShetty, S.; Nayak, J.; Shetty, A.N.-
2021Influence of Superplasticizers on Blended Cement and Their Effect on Flow Characteristics by Incorporating PGBS as Partial Replacement for Fine AggregatesArpitha D.; Sudarshan V.J.; Thilak Kumar Y.T.; Rajasekaran C.-
2019Influence of Support Conditions on the Hydroelastic Behaviour of Floating Thick Elastic PlatePraveen, K.M.; Karmakar, D.; Soares, C.G.-
2018Influence of surface modification on wear behavior of fly ash cenosphere/epoxy syntactic foamShahapurkar, K.; Chavan, V.B.; Doddamani, M.; Mohankumar, G.C.-
Showing results 4848 to 4867 of 10116 < previous   next >