Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
16 results
Search Results
Item Studies on copper coated polysulfone/modified poly isobutylene alt-maleic anhydride blend membrane and its antibiofouling property(2013) Isloor, A.M.; Ganesh, B.M.; Isloor, S.; A.F., A.F.; Nagaraj, H.S.; Pattabi, M.As nanofiltration is gaining more and more importance in the field of desalination, one has to address the many obstacles in order to achieve effective/efficient filtration. One such issue is biofouling and microbial attack to the membrane. This paper describes about the study on copper coating onto the membrane surface as biofouling protective layer. This is an attempt to come up with a new approach for desalination and an antimicrobial membrane. The work indicates that, the copper coated membrane can resist the possible microbial attack to some extent while maintaining good salt rejection and appreciable flux. SEM and EDX studies had shown the distribution of copper on the membrane surface. The copper coated membrane had shown the maximum salt rejection of about 96% for 3500ppm NaCl solution and also it had shown the pure water flux of 36Lm-2h-1. © 2012 Elsevier B.V.Item Preparation and characterization of PPEES/chitosan composite nanofiltration membrane(2013) Shenvi, S.S.; Abdul Rashid, S.A.; A.F., A.F.; Kassim, M.A.; Isloor, A.M.Composite membrane having chitosan (CH) as the active layer supported on Poly(1,4-phenylene ether ether sulfone) (PPEES) membrane was synthesized in the current study. The chitosan layer was crosslinked by glutaraldehyde in two different concentrations. The scanning electron microscopic images and hydraulic permeability coefficient revealed the ultrafiltration (UF) nature of the neat PPEES membrane. This was used as a new support material for the casting of chitosan layer in order to get composite membranes. The composite nature of the PPEES/CH membranes was confirmed by FESEM and DSC analysis. The Infrared spectroscopy results confirmed the crosslinking of the chitosan surface by glutaraldehyde (GA). The changes in the hydrophobic nature of the PPEES membrane surface due to deposition of chitosan active layer followed by crosslinking were studied by their contact angle measurement and water flux study. From our studies, PPEES has proved to be a good support membrane for preparation of composite membranes. Increase in GA concentration increased the salt rejection of the membrane up to 34% for NaCl and 53% for MgSO4 on one hand with a simultaneous decrease in the flux values. The hydraulic permeability coefficient values confirmed that the prepared membranes are in nanofiltration range. © 2012 Elsevier B.V.Item Performance improvement of polysulfone ultrafiltration membrane using N-succinyl chitosan as additive(2013) Kumar, R.; Isloor, A.M.; A.F., A.F.; Matsuura, T.A water soluble chitosan derivative, N-succinyl chitosan (NSCS), was blended with polysulfone (PSf) in three different compositions to fabricate PSf/NSCS blend membranes. The blending of polymers was confirmed by Attenuated Total Reflectance Infra-Red (ATR-IR) spectroscopy. The membranes were characterized by Scanning Electron Microscopy (SEM) images for their cross-sectional morphology. Pure water flux, water uptake and contact angle of the PSf/NSCS blend membranes were measured and compared with the pristine polysulfone membrane. The PSf/NSCS blend membranes showed enhanced hydrophilicity and permeation fluxes compared to the pristine polysulfone membrane. The membrane antifouling property was determined by filtering the bovine serum albumin (BSA) solution. The maximum flux recovery ratio (FRR) of 70% was observed by the PSf/NSCS blend membrane with 20% NSCS content. The PSf/NSCS membranes with the PSf:NSCS ratios of 80:20 and 90:10 showed nearly the same fluxes as those of polysulfone/polyethylene glycol (PSf/PEG) blend membranes with the same compositions. The hydrophilic derivative of chitosan NSCS acted as an excellent additive in improving PSf ultrafiltration properties. © 2013 Elsevier B.V.Item Antifouling and performance enhancement of polysulfone ultrafiltration membranes using CaCO3 nanoparticles(2013) Nair, A.K.; Isloor, A.M.; Kumar, R.; A.F., A.F.Calcium carbonate nanoparticles were synthesized from calcium nitrate via chemical precipitation method. The nanoparticles were characterized using scanning electron microscope (SEM), Attenuated total reflectance infra red (ATR-IR) spectrum and by X-ray diffraction (XRD). These nanoparticles were used as additive for polysulfone (PSf) ultrafiltration membrane along with polyethylene glycol (PEG) as pore forming agent. The PSf hybrid membranes were characterized by ATR-IR, XRD, and SEM studies. ATR-IR and XRD results indicated the successful incorporation of the nanoparticles in the membranes. Cross sectional images of the membranes along with the elemental mapping of calcium on the membrane surface were assessed using SEM. Hydrophilicity of the membranes was evaluated in terms of contact angle measurements. The permeability of the membranes was determined by measuring the pure water flux (PWF). Membranes were also subjected to antifouling studies using bovine serum albumin (BSA) as the standard protein for rejection. The membranes showed better permeability and antifouling property with the increased addition of CaCO3 nanoparticles. © 2013 Elsevier B.V.Item Synthesis and characterization of novel water soluble derivative of Chitosan as an additive for polysulfone ultrafiltration membrane(2013) Kumar, R.; Isloor, A.M.; A.F., A.F.; Matsuura, T.A novel water soluble Chitosan derivative N-propylphosphonic Chitosan (NPPCS) having a terminal phosphonic acid group was synthesized by reacting Chitosan with Hydroxybenzotriazole (HOBt) and propylphosphonic anhydride (T3P)® via one pot reaction. The novel derivative was characterized by 1H NMR, Attenuated Total Reflectance Infra Red (ATR-IR) spectroscopy and XRD. Due to insolubility of NPPCS in organic solvents, a new process was demonstrated for blending of NPPCS with Polysulfone. The proper blending of NPPCS with Polysulfone was confirmed by ATR-IR spectroscopy. The improved hydrophilicity of PSf/NPPCS membranes was confirmed by contact angle measurement. The permeation studies showed increased flux of PSf/NPPCS membranes as compared to the pristine Polysulfone membrane. The antifouling property of PSf/NPPCS membrane was determined by Bovine Serum Albumin (BSA) protein rejection studies. The membranes showed the enhanced antifouling property as compared to pristine Polysulfone membranes with a maximum of 74% flux recovery ratio (FRR) value. © 2013 Elsevier B.V.Item Preparation and evaluation of heavy metal rejection properties of polysulfone/chitosan, polysulfone/N-succinyl chitosan and polysulfone/N-propylphosphonyl chitosan blend ultrafiltration membranes(Elsevier, 2014) Kumar, R.; Isloor, A.M.; A.F., A.F.Heavy metal rejection properties of chitosan based polysulfone/chitosan (PSf/CS), polysulfonef/N-succinyl chitosan (PSf/NSCS) and polysulfone/N-propylphosphonyl chitosan (PSf/NPPCS) ultrfiltration (UF) membranes were evaluated. The rejection of membranes towards the copper, cadmium and nickel ions was studied during ultrafiltration (UF) by polymer enhanced ultrafiltration (PEUF) processes. The flux change during the UF process and the effect of pH on the rejection were determined. The membrane recycling property was studied during PEUF process by filtering chelated CuSO4 solution. A maximum of 78% of Cu, 73% of Ni and 68% of Cd rejection for M-5 membrane, 75% of Cu, 71% of Ni and 66% of Cd rejection for M-8 membrane and 76% of Cu, 69% of Ni and 66% of Cd rejection for M-2 membrane with reasonably good flux was observed. Further improvement in heavy metal ion rejection was achieved by PEUF process. Membrane M-5 showed a maximum of 98%, 95% and 92% rejection for Cu, Ni and Cd respectively with steady state flux of 117L/m2h. An increase in membrane recycling property after the metal ion rejection was mainly attributed to the hydrophilicity of CS, NSCS and NPPCS. © 2014 Elsevier B.V.Item Preparation and antifouling properties of PVDF ultrafiltration membranes with polyaniline (PANI) nanofibers and hydrolysed PSMA (H-PSMA) as additives(Elsevier, 2014) Pereira, V.R.; Isloor, A.M.; Bhat, K.U.; A.F., A.F.Polyaniline (PANI) nanofibers were used as hydrophilic additives to study their effect on the performance of polyvinylidene fluoride (PVDF) ultrafiltration (UF) membranes. PVDF UF membranes were prepared by the phase inversion method with hydrolyzed polystyrene-co-maleic anhydride (H-PSMA) and PANI nanofibers as additives. PANI nanofibers were synthesized by rapid mixing reaction and were used as a hydrophilic modifying agent with varying concentrations (0-1.5 wt.%) in the membranes. The synthesized PANI nanofibers were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis. Hydrolyzed PSMA was prepared by the hydrolysis of PSMA and was used as a novel pore forming additive. The addition of PANI nanofibers into the membranes increased the membrane hydrophilicity, porosity, water uptake and permeability. The membranes also showed good antifouling nature during BSA (bovine serum albumin) filtration when compared to the pristine membrane without PANI nanofibers. Membrane with 1.0 wt.% PANI content showed highest permeability among the synthesized membranes. The membrane having highest permeability was subjected to heavy metal ion rejection which showed high rejection of 98.52% and 97.38% for heavy metal ions Pb2+ and Cd2+ respectively. © 2014 Elsevier B.V.Item Preparation, characterization and the effect of PANI coated TiO2 nanocomposites on the performance of polysulfone ultrafiltration membranes(Royal Society of Chemistry, 2015) Pereira, V.R.; Isloor, A.M.; Ahmed, A.A.; A.F., A.F.Polysulfone ultrafiltration (UF) membranes with PANI-TiO2 (polyaniline-titania) nanocomposites and PEG 1000 (Polyethylene Glycol 1000) as additives were prepared by the phase inversion method. PANI-TiO2 nanocomposites were synthesized by coating TiO2 nanotubes with PANI via chemical oxidative polymerization. The synthesized PANI-TiO2 nanocomposite was characterized by Fourier Transform Infrared Spectroscopy (FTIR), X-ray diffraction (XRD) and Transmission Electron Microscope (TEM) analysis. PANI-TiO2 nanocomposites with varying concentrations (0-1.5 wt%) were dispersed in the polysulfone membrane matrix with N-methyl-2-pyrrolidone (NMP) as solvent along with PEG 1000 as the pore former. The effect of addition of PANI-TiO2 nanocomposites with different concentrations (0-1.5 wt%) on the membrane structure, performance, hydrophilicity and the antifouling nature of the membranes was analyzed. PANI-TiO2 nanocomposite membranes showed better hydrophilicity, improved permeability, enhanced porosity, water uptake and good antifouling ability when compared with neat polysulfone membranes. The performance of the membranes improved with the increase in the addition of the PANI-TiO2 nanocomposite. However, the membrane performance decreased slightly at 1.5 wt% addition of PANI-TiO2 due to the agglomeration of PANI-TiO2 at higher concentration. The well performed membranes were also subjected to heavy metal ion rejection. The membranes showed a rejection of 83.75% and 73.41% during the polymer enhanced ultrafiltration (PEUF) process and a rejection of 68% and 53.78% during the UF process for Pb2+ and Cd2+ respectively. © The Royal Society of Chemistry and the Centre National de la Recherche Scientifique 2015.Item Preparation and characterization of novel PSf/PVP/PANI-nanofiber nanocomposite hollow fiber ultrafiltration membranes and their possible applications for hazardous dye rejection(Elsevier, 2015) Kajekar, A.J.; Dodamani, B.M.; Isloor, A.M.; Zulhairun, A.K.; Cheer, N.B.; A.F., A.F.; Shilton, S.J.In the present study, PANI (polyaniline)-nanofibers were synthesized by interfacial polymerization technique, dispersed in n-Methyl-2-Pyrrolidone (NMP) solvent and blended with PVP (Polyvinylpyrrolidone)/PSf (Polysulfone) for preparing the novel hollow fiber membrane by dry-wet spinning technique. The newly prepared nanocomposite ultrafiltration hollow fiber membrane is characterized by Scanning Electron Microscope (SEM), Contact Angle, Zeta Potential and Differential Scanning Calorimeter (DSC). Filtration studies are conducted to measure the membrane pure water flux (PWF), rejection of hazardous dye (Reactive Red 120) and fouling resistance. The maximum rejections are obtained for M 0.5 membrane with 99.25% rejection of RR120 hazardous dye at 2. bar pressure. The pure water flux, percentage rejection, antifouling property and thermal resistance increased with an increase in PANI-nanofiber concentration. The contact angle of the membrane decreased with increasing PANI-nanofiber concentration, which indicated increased hydrophilicity of the new membranes. © 2015 Elsevier B.V.Item Performance enhancement of polysulfone ultrafiltration membrane using TiO2 nanofibers(Taylor and Francis Inc. 325 Chestnut St, Suite 800 Philadelphia PA 19106, 2016) Nair, A.K.; Shalin, P.M.; JagadeeshBabu, P.E.Titanium dioxide nanofibers were synthesized via alkaline hydrothermal method using TiO2 nanopowder. The hydrothermal method was optimized by studying the operating variables to obtain nanosized TiO2 fibers. These nanofibers were used to make composite polysulfone ultrafiltration membranes along with polyethylene glycol as pore forming agent. The obtained samples were characterized using scanning electron microscope, X-ray diffraction, and attenuated total reflectance infrared spectroscopy. Contact angle measurements were used to estimate hydrophilicity of the membrane. Performance of the membrane was analyzed using pure water flux studies and antifouling studies with bovine serum albumin as the standard protein for rejection. The composite membranes exhibited better performance in both permeability and antifouling property. © 2015 Balaban Desalination Publications. All rights reserved.