Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
15 results
Search Results
Item 6 CTA 8.3 G1-1 Cummins engine performance & exhaust emission tests using methyl ester Mahua oil and diesel fuel blends(2008) Godiganur, S.; Reddy, R.P.; Murthy, C.H.S.A Cummins 6 CTA 8.3G1-1 turbocharged DI diesel engine was fueled with blends of esters of Mahua oil and the performance and emissions were compared with diesel. The neat biodiesel, 10%, 20%, 40%, 60%, 80%, and base fuel were tested at constant load (28% of rated load) and at constant speed of 1500 rpm. This experiment is conducted on D.G Set, used to supply power to mining equipments in MSPL Iron Ore Company Hospet. Dist. Bellary. The objective of this study was to evaluate the impact of various blends of biodiesel on engine performance and emissions. Neat Mahua oil poses some problems when subjected to prolonged usage in CI engine. These problems can be reduced to minimum by subjecting the Mahua oil to the process of transesterification. Various properties of the biodiesel thus developed are evaluated and compared in relation to that of conventional diesel oil. Copyright © Enviromedia.Item 6BTA 5.9 G2-1 Cummins engine performance and emission tests using methyl ester mahua (Madhuca indica) oil/diesel blends(2009) Godiganur, S.; Suryanarayana Murthy, C.H.; Reddy, R.P.Neat mahua oil poses some problems when subjected to prolonged usage in CI engine. The transesterification of mahua oil can reduce these problems. The use of biodiesel fuel as substitute for conventional petroleum fuel in heavy-duty diesel engine is receiving an increasing amount of attention. This interest is based on the properties of bio-diesel including the fact that it is produced from a renewable resource, its biodegradability and potential to exhaust emissions. A Cummins 6BTA 5.9 G2- 1, 158 HP rated power, turbocharged, DI, water cooled diesel engine was run on diesel, methyl ester of mahua oil and its blends at constant speed of 1500 rpm under variable load conditions. The volumetric blending ratios of biodiesel with conventional diesel fuel were set at 0, 20, 40, 60, and 100. Engine performance (brake specific fuel consumption, brake specific energy consumption, thermal efficiency and exhaust gas temperature) and emissions (CO, HC and NOx) were measured to evaluate and compute the behavior of the diesel engine running on biodiesel. The results indicate that with the increase of biodiesel in the blends CO, HC reduces significantly, fuel consumption and NOx emission of biodiesel increases slightly compared with diesel. Brake specific energy consumption decreases and thermal efficiency of engine slightly increases when operating on 20% biodiesel than that operating on diesel. © 2008 Elsevier Ltd. All rights reserved.Item Performance and emission characteristics of a Kirloskar HA394 diesel engine operated on fish oil methyl esters(2010) Godiganur, S.; Suryanarayana Murthy, Ch.; Reddy, R.P.The high viscosity of fish oil leads to problem in pumping and spray characteristics. The inefficient mixing of fish oil with air leads to incomplete combustion. The best way to use fish oil as fuel in compression ignition (CI) engines is to convert it into biodiesel. It can be used in CI engines with very little or no engine modifications. This is because it has properties similar to mineral diesel. Combustion tests for methyl ester of fish oil and its blends with diesel fuel were performed in a kirloskar H394 DI diesel engine, to evaluate fish biodiesel as an alternative fuel for diesel engine, at constant speed of 1500 rpm under variable load conditions. The tests showed no major deviations in diesel engine's combustion as well as no significant changes in the engine performance and reduction of main noxious emissions with the exception on NOx. Overall fish biodiesel showed good combustion properties and environmental benefits. © 2009 Elsevier Ltd. All rights reserved.Item Performance and emission characteristics of double cylinder CI engine operated with cardanol bio fuel blends(2012) Mallikappa, D.N.; Reddy, R.P.; Murthy, C.S.N.India imports more than seventy percent of the oil it uses and is looking for alternative fuel to reduce its dependence on imports. In India, bio fuels derived from non-edible oils is considered as a renewable alternative to the fossil diesel. The cost of the biodiesel is higher than diesel and hence in this work, cardanol was used as an alternative renewable fuel for the diesel engine. The engine tests were conducted on a double cylinder, direct injection, compression ignition engine. From the engine tests, it is observed that the brake power increases (by 70% approximately) as load increases. Brake specific energy conversion decreases (by 25-30% approximately) with increase in brake power. Brake thermal efficiency increases with higher brake power and emission levels (HC, CO, NOX) were nominal up to 20% blends. © 2011 Elsevier Ltd.Item Influence of low-temperature combustion and dimethyl ether-diesel blends on performance, combustion, and emission characteristics of common rail diesel engine: a CFD study(Springer Verlag service@springer.de, 2017) Lamani, V.T.; Yadav, A.K.; Gottekere Narayanappa, K.G.Due to presence of more oxygen, absence of carbon-carbon (C-C) bond in chemical structure, and high cetane number of dimethyl ether (DME), pollution from DME operated engine is less compared to diesel engine. Hence, the DME can be a promising alternative fuel for diesel engine. The present study emphasizes the effect of various exhaust gas recirculation (EGR) rates (0–20%) and DME/Diesel blends (0–20%) on combustion characteristics and exhaust emissions of common rail direct injection (CRDI) engine using three-dimensional computational fluid dynamics (CFD) simulation. Extended coherent flame model-3 zone (ECFM-3Z) is implemented to carry out combustion analysis, and k-?-f model is employed for turbulence modeling. Results show that in-cylinder pressure marginally decreases with employing EGR compared to without EGR case. As EGR rate increases, nitrogen oxide (NO) formation decreases, whereas soot increases marginally. Due to better combustion characteristics of DME, indicated thermal efficiency (ITE) increases with the increases in DME/diesel blend ratio. Adverse effect of EGR on efficiency for blends is less compared to neat diesel, because the anoxygenated region created due to EGR is compensated by extra oxygen present in DME. The trade-off among NO, soot, carbon monoxide (CO) formation, and efficiency is studied by normalizing the parameters. Optimum operating condition is found at 10% EGR rate and 20% DME/diesel blend. The maximum indicated thermal efficiency was observed for DME/diesel ratio of 20% in the present range of study. Obtained results are validated with published experimental data and found good agreement. © 2017, Springer-Verlag Berlin Heidelberg.Item Performance, emission, and combustion characteristics of twin-cylinder common rail diesel engine fuelled with butanol-diesel blends(Springer Verlag service@springer.de, 2017) Lamani, V.T.; Yadav, A.K.; Gottekere, K.N.Nitrogen oxides and smoke are the substantial emissions for the diesel engines. Fuels comprising high-level oxygen content can have low smoke emission due to better oxidation of soot. The objective of the paper is to assess the potential to employ oxygenated fuel, i.e., n-butanol and its blends with the neat diesel from 0 to 30% by volume. The experimental and computational fluid dynamic (CFD) simulation is carried out to estimate the performance, combustion, and exhaust emission characteristics of n-butanol-diesel blends for various injection timings (9°, 12°, 15°, and 18°) using modern twin-cylinder, four-stroke, common rail direct injection (CRDI) engine. Experimental results reveal the increase in brake thermal efficiency (BTE) by ~ 4.5, 6, and 8% for butanol-diesel blends of 10% (Bu10), 20% (Bu20), and 30% (Bu30), respectively, compared to neat diesel (Bu0). Maximum BTE for Bu0 is 38.4%, which is obtained at 12° BTDC; however, for Bu10, Bu20 and Bu30 are 40.19, 40.9, and 41.7%, which are obtained at 15° BTDC, respectively. Higher flame speed of n-butanol-diesel blends burn a large amount of fuel in the premixed phase, which improves the combustion as well as emission characteristics. CFD and experimental results are compared and validated for all fuel blends for in-cylinder pressure and nitrogen oxides (NOx), and found to be in good agreement. Both experimental and simulation results witnessed in reduction of smoke opacity, NOx, and carbon monoxide emissions with the increasing n-butanol percentage in diesel fuel. © 2017, Springer-Verlag GmbH Germany.Item Effect of fuel injection strategies and EGR on biodiesel blend in a CRDI engine(Elsevier Ltd, 2019) Bhowmick, P.; Jeevanantham, A.K.; Bragadeshwaran, B.; Kasianantham, K.; Arumuga Perumal, D.A.; Viswanathan, V.; Vora, K.C.; Jain, A.Biodiesel appears as a replenishable and sustainable energy source and can be used a direct replacement to petro-diesel without any major transformations in ongoing diesel engines. This work concentrates on production of Calophyllum Inophyllum biodiesel (CIB) and preparing 10% blend (CIB10) sample to investigate the effects of varying the injection strategies and exhaust gas recirculation (EGR) in common-rail direct injection engine. The experimental results shows that 10% of pilot fuel and 90% main injection strategy (B10@P10-M90) is superior among all others injection strategies with respect to pure diesel. B10@P10-M90 fuel injection strategy produces the maximum efficiency of 35.8% and lowest fuel consumption of 0.25 kg/kWh compared to all the injection strategies. The carbon monoxide (CO) and hydrocarbon (HC) emissions are also found to be quite low compared to all the other test samples including pure diesel. However B10@P10-M90 results in higher average oxides of nitrogen (NOx) emission which is 18.9% higher in contrast to conventional diesel at full load condition. With the implementation of 10% and 20% EGR with B10@P10-M90, the average NOx emissions decreased by 14.4% and 27.6% respectively compared to B10@P10-M90 without any EGR without significant loss in the performance of the existing diesel engine. © 2019 Elsevier LtdItem Effect of 1-pentanol addition and EGR on the combustion, performance and emission characteristic of a CRDI diesel engine(Elsevier Ltd, 2020) Radheshyam; Santhosh, K.; Kumar, G.N.Experimental study of 1-pentanol addition and EGR rates on the combustion, performance and emission of a CRDI diesel engine is carried out in this work. 1-Pentanol being a higher alcohol has fuel properties comparable to diesel. Experiments were conducted on a 4 stroke two cylinder, CRDI diesel engine running at a constant speed of 2000 rpm for lower load and higher load. Test fuels were prepared by blending the 1-pentanol with diesel, and tests were carried out for 5%, 10%, 20%, 30% and 40%, 1-pentanol blended in diesel on a volume basis. Effect of EGR rates of 10% and 20% were also studied. It had observed that engine can be run up to 30% of 1-pentanol blended fuel without any engine modification, but with raise in the percentage of 1-pentanol in the blends, BSFC increases and BTE decreases. Combustion characteristic for blended fuel depends upon the load. At higher load due to premixed combustion MGT, CP and NHR were almost same compared to the diesel. Reduction in NOx emissions was noted for all the fuel blends at the cost of HC and CO emission. 1-pentanol is a renewable biofuel, with use of 1-pentanol the dependency on petrodiesel can be overcome. © 2019 Elsevier LtdItem Investigation of preheated Dhupa seed oil biodiesel as an alternative fuel on the performance, emission and combustion in a CI engine(Elsevier Ltd, 2021) Kodate, S.V.; Satyanarayana Raju, P.; Yadav, A.K.; Kumar, G.N.The present study investigates the suitability of preheated Vateria indica methyl ester (VIME) as an alternative fuel for a diesel engine. VIME is a renewable, non-toxic and sustainable alternative biodiesel obtained from Dhupa fat by transesterification. This study aims to evaluate the combustion, performance, and emission characteristics of four different blends such as B0 (0% VIME and 100% mineral diesel), B30, B50 and B100 at elevated fuel inlet temperatures ranging from 35 °C to 95 °C. The tests are carried out in a single cylinder diesel engine at optimum loading condition and fixed speed. Results are obtained in terms of brake thermal efficiency (BTE), brake specific fuel consumption (BSFC), in-cylinder pressure, heat release rate and exhaust emissions (CO, HC, NOX, CO2 and soot). It is observed that the preheating of blends decreases the viscosity which enhances fuel spray characteristics, leading to higher engine performance, lower CO and HC emissions with a slight increase in NOX and CO2 emissions. BTE and peak in-cylinder pressure for B100 at 95 °C and 75% load are increased by 7.44%, 2.97% respectively compared to unheated B100 biodiesel. BSFC, CO, HC emissions at 75% load for B100 at 95 °C are reduced by 26.73%, 28.08%, 42.7% respectively compared to unheated B100. © 2021 Elsevier LtdItem Effect of variable compression ratio and equivalence ratio on performance, combustion and emission of hydrogen port injection SI engine(Elsevier Ltd, 2022) Pandey, J.K.; Kumar, G.N.The present study includes an experimental investigation of the performance, combustion, and emission parameters of a hydrogen port fueled SI engine under wide-open throttle. The compression ratio (CR) is varied from 10 to 15, equivalence ratio (φ) from 0.4 to 1.0, and speed from 1400RPM to 1800RPM. The ignition timing is maintained at 20° before the top dead center. The brake thermal efficiency increases by nearly 10% from CR10 to CR15, and it also increased by 13.7% by changing φ from 0.4 to 0.9. Similarly, BP increases in the same fashion. The combustion enhances with an increase in peak pressure by increasing CR from 10 to 15 and φ from 0.4 to 0.9; however, φ 1.0 exhibits a negative trend. However, the NOX emission increases continuously with CR and φ, and so as the exhaust gas temperature. The carbon-based emissions are negligible, and volumetric efficiency decreases with φ and increases with CR. © 2021 Elsevier Ltd