Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
18 results
Search Results
Item Performance and emission characteristics of a Kirloskar HA394 diesel engine operated on fish oil methyl esters(2010) Godiganur, S.; Suryanarayana Murthy, Ch.; Reddy, R.P.The high viscosity of fish oil leads to problem in pumping and spray characteristics. The inefficient mixing of fish oil with air leads to incomplete combustion. The best way to use fish oil as fuel in compression ignition (CI) engines is to convert it into biodiesel. It can be used in CI engines with very little or no engine modifications. This is because it has properties similar to mineral diesel. Combustion tests for methyl ester of fish oil and its blends with diesel fuel were performed in a kirloskar H394 DI diesel engine, to evaluate fish biodiesel as an alternative fuel for diesel engine, at constant speed of 1500 rpm under variable load conditions. The tests showed no major deviations in diesel engine's combustion as well as no significant changes in the engine performance and reduction of main noxious emissions with the exception on NOx. Overall fish biodiesel showed good combustion properties and environmental benefits. © 2009 Elsevier Ltd. All rights reserved.Item Influence of low-temperature combustion and dimethyl ether-diesel blends on performance, combustion, and emission characteristics of common rail diesel engine: a CFD study(Springer Verlag service@springer.de, 2017) Lamani, V.T.; Yadav, A.K.; Gottekere Narayanappa, K.G.Due to presence of more oxygen, absence of carbon-carbon (C-C) bond in chemical structure, and high cetane number of dimethyl ether (DME), pollution from DME operated engine is less compared to diesel engine. Hence, the DME can be a promising alternative fuel for diesel engine. The present study emphasizes the effect of various exhaust gas recirculation (EGR) rates (0–20%) and DME/Diesel blends (0–20%) on combustion characteristics and exhaust emissions of common rail direct injection (CRDI) engine using three-dimensional computational fluid dynamics (CFD) simulation. Extended coherent flame model-3 zone (ECFM-3Z) is implemented to carry out combustion analysis, and k-?-f model is employed for turbulence modeling. Results show that in-cylinder pressure marginally decreases with employing EGR compared to without EGR case. As EGR rate increases, nitrogen oxide (NO) formation decreases, whereas soot increases marginally. Due to better combustion characteristics of DME, indicated thermal efficiency (ITE) increases with the increases in DME/diesel blend ratio. Adverse effect of EGR on efficiency for blends is less compared to neat diesel, because the anoxygenated region created due to EGR is compensated by extra oxygen present in DME. The trade-off among NO, soot, carbon monoxide (CO) formation, and efficiency is studied by normalizing the parameters. Optimum operating condition is found at 10% EGR rate and 20% DME/diesel blend. The maximum indicated thermal efficiency was observed for DME/diesel ratio of 20% in the present range of study. Obtained results are validated with published experimental data and found good agreement. © 2017, Springer-Verlag Berlin Heidelberg.Item Performance, emission, and combustion characteristics of twin-cylinder common rail diesel engine fuelled with butanol-diesel blends(Springer Verlag service@springer.de, 2017) Lamani, V.T.; Yadav, A.K.; Gottekere, K.N.Nitrogen oxides and smoke are the substantial emissions for the diesel engines. Fuels comprising high-level oxygen content can have low smoke emission due to better oxidation of soot. The objective of the paper is to assess the potential to employ oxygenated fuel, i.e., n-butanol and its blends with the neat diesel from 0 to 30% by volume. The experimental and computational fluid dynamic (CFD) simulation is carried out to estimate the performance, combustion, and exhaust emission characteristics of n-butanol-diesel blends for various injection timings (9°, 12°, 15°, and 18°) using modern twin-cylinder, four-stroke, common rail direct injection (CRDI) engine. Experimental results reveal the increase in brake thermal efficiency (BTE) by ~ 4.5, 6, and 8% for butanol-diesel blends of 10% (Bu10), 20% (Bu20), and 30% (Bu30), respectively, compared to neat diesel (Bu0). Maximum BTE for Bu0 is 38.4%, which is obtained at 12° BTDC; however, for Bu10, Bu20 and Bu30 are 40.19, 40.9, and 41.7%, which are obtained at 15° BTDC, respectively. Higher flame speed of n-butanol-diesel blends burn a large amount of fuel in the premixed phase, which improves the combustion as well as emission characteristics. CFD and experimental results are compared and validated for all fuel blends for in-cylinder pressure and nitrogen oxides (NOx), and found to be in good agreement. Both experimental and simulation results witnessed in reduction of smoke opacity, NOx, and carbon monoxide emissions with the increasing n-butanol percentage in diesel fuel. © 2017, Springer-Verlag GmbH Germany.Item Calorespirometric investigation of Streptococcus zooepidemicus metabolism: Thermodynamics of anabolic payload contribution by growth and hyaluronic acid synthesis(Elsevier B.V., 2019) Mohan, N.; Allampalli, S.S.; Achar, A.; Swaminathan, N.; Sivaprakasam, S.Thermodynamic analysis of carbon flux competing for pathways of S. zooepidemicus in the production of catabolic (Lactic acid) and anabolic (Biomass and Hyaluronic Acid) products is investigated to assimilate the thermodynamic advantages of biopolymer production. Calorespirometry was employed to fingerprint the on-going HA production process and to predict reliable estimation of catabolic and anabolic product yields. This study accomplished the HA production at different initial glucose concentrations, S0 (10–60 g/L) to subject different levels of anabolic burden on S. zooepidemicus. Anabolic payload comprising Biomass and HA yields showed a concomitant decrease with respect to the increased concentration of S0. Chemical entropy exported over the cell surface in the form of LA production exhibited an increasing trend at different levels of glucose, thus reducing the total yields of biomass and HA. Thermodynamically anabolic load contributed by biomass and HA production found to have minor influence over the driving force of S. zooepidemicus metabolism due to their lower yields. The entropy contribution to the overall driving force is significant (T?SX= [Formula presented] ?rGX) at the higher biomass yields. This study allows the prediction of optimum biomass yield towards enhanced HA production and addresses the scope of ‘thermodynamic constraints’ application in real-time process monitoring and control using data reconciliation strategy in the near future. © 2019 Elsevier B.V.Item Effect of 1-pentanol addition and EGR on the combustion, performance and emission characteristic of a CRDI diesel engine(Elsevier Ltd, 2020) Radheshyam; Santhosh, K.; Kumar, G.N.Experimental study of 1-pentanol addition and EGR rates on the combustion, performance and emission of a CRDI diesel engine is carried out in this work. 1-Pentanol being a higher alcohol has fuel properties comparable to diesel. Experiments were conducted on a 4 stroke two cylinder, CRDI diesel engine running at a constant speed of 2000 rpm for lower load and higher load. Test fuels were prepared by blending the 1-pentanol with diesel, and tests were carried out for 5%, 10%, 20%, 30% and 40%, 1-pentanol blended in diesel on a volume basis. Effect of EGR rates of 10% and 20% were also studied. It had observed that engine can be run up to 30% of 1-pentanol blended fuel without any engine modification, but with raise in the percentage of 1-pentanol in the blends, BSFC increases and BTE decreases. Combustion characteristic for blended fuel depends upon the load. At higher load due to premixed combustion MGT, CP and NHR were almost same compared to the diesel. Reduction in NOx emissions was noted for all the fuel blends at the cost of HC and CO emission. 1-pentanol is a renewable biofuel, with use of 1-pentanol the dependency on petrodiesel can be overcome. © 2019 Elsevier LtdItem Impact of changing compression ratio on engine characteristics of an SI engine fueled with equi-volume blend of methanol and gasoline(Elsevier Ltd, 2020) Nuthan Prasad, B.S.; Pandey, J.K.; Kumar, G.N.In the present investigation, experiments were conducted in wide open throttle condition (WOT) for different speed ranging from 1200 rpm to 1800 rpm at an interval of 200 on a single-cylinder four-stroke variable compression ratio (VCR) SI engine. The engine fueled with equi-volume blend of methanol/gasoline fuel, while 14° BTDC ignition timing is maintained for all three different compression ratios (8, 9 & 10). Increasing the compression ratio from CR8 to CR10 for the methanol/gasoline blend has improved combustion efficiency by increasing the peak pressure and net heat release value by 27.5% and 30% respectively at a speed of 1600 rpm. The performance results show a good agreement of improvisation of 25% increase in BTE, and BSFC reduction by 19% at compression ratio 10:1. At higher compression ratio 10:1, there was a significant decrease observed in CO and HC by 30–40%, and the same trend is observed at all speeds; however, NOx emission increased with the increasing CR. © 2019 Elsevier LtdItem Effect of injection time on combustion, performance and emission characteristics of direct injection CI engine fuelled with equi-volume of 1-hexanol/diesel blends(Elsevier Ltd, 2021) Santhosh, K.; Kumar, G.N.In this experimental research work, the effect of 1-Hexanol on engine parameters is studied and to improve the combustion, performance and emission characteristics of CI engine, fuel injection time is advanced and retarded to know the best possible injection time. The experiment is conducted in a twin-cylinder, common rail direct injection diesel engine, speed (2000 rpm) of the engine is constant throughout the experiment and the engine load is varied as 20%, 40%, 60% and 80%. In this experiment equi-volume of 1-Hexanol/diesel blends is used as a fuel, the experiment is conducted for standard (12°BTDC), advanced (15°BTDC) and retard (9°BTDC) injection time. The obtained results are compared with baseline readings taken at standard injection time. The advanced injection time shows the best results compared to standard and retard injection time. The advanced injection time shows improved combustion parameters, the combustion peak moves near to TDC. An increment of 14.28% in BTE is noted for 1-Hexanol blend. The CO and HC emission decreases with advanced injection time, whereas higher NOx emission is noted. It is concluded that 50% of 1-Hexanol can be used in CI engine with slight modification in injection time; the advanced injection time gives improved efficiency. © 2020 Elsevier LtdItem Auto-combustion synthesis of narrow band-gap bismuth ferrite nanoparticles for solar photocatalysis to remediate azo dye containing water(Springer Science and Business Media Deutschland GmbH, 2021) Kalikeri, S.; Shetty K, V.Narrow band gap of ferrites makes it a good photocatalyst, and it plays very prominent role in the level of degradation of organic dyes by photocatalysis. In the current study, bismuth ferrite (BFO) nanoparticles were synthesized by auto-combustion technique. The synthesized BFO particles have the average crystallite size of 33 nm and band gap energy of 1.9 eV. As revealed by microscopic images, uniform, distinct, and hexahedral shaped BFO nanoparticles of 42.7 nm are formed. The BFO nanoparticles exhibited visible and solar light-mediated photocatalytic activity in degrading Acid Yellow-17. The optimum pH and catalyst loading were found to be pH 5 and 0.2 g/L respectively. Around complete degradation under solar and 95% degradation under visible light could be achieved within 135 min of irradiation. Around 85% and 83% chemical oxygen demand (COD) removal could also be achieved under solar and visible light respectively. The degradation followed first-order kinetics in terms of COD removal. The BFO nanoparticles are promising as solar light active catalysts for wastewater treatment. © 2020, Springer-Verlag GmbH Germany, part of Springer Nature.Item Investigation of preheated Dhupa seed oil biodiesel as an alternative fuel on the performance, emission and combustion in a CI engine(Elsevier Ltd, 2021) Kodate, S.V.; Satyanarayana Raju, P.; Yadav, A.K.; Kumar, G.N.The present study investigates the suitability of preheated Vateria indica methyl ester (VIME) as an alternative fuel for a diesel engine. VIME is a renewable, non-toxic and sustainable alternative biodiesel obtained from Dhupa fat by transesterification. This study aims to evaluate the combustion, performance, and emission characteristics of four different blends such as B0 (0% VIME and 100% mineral diesel), B30, B50 and B100 at elevated fuel inlet temperatures ranging from 35 °C to 95 °C. The tests are carried out in a single cylinder diesel engine at optimum loading condition and fixed speed. Results are obtained in terms of brake thermal efficiency (BTE), brake specific fuel consumption (BSFC), in-cylinder pressure, heat release rate and exhaust emissions (CO, HC, NOX, CO2 and soot). It is observed that the preheating of blends decreases the viscosity which enhances fuel spray characteristics, leading to higher engine performance, lower CO and HC emissions with a slight increase in NOX and CO2 emissions. BTE and peak in-cylinder pressure for B100 at 95 °C and 75% load are increased by 7.44%, 2.97% respectively compared to unheated B100 biodiesel. BSFC, CO, HC emissions at 75% load for B100 at 95 °C are reduced by 26.73%, 28.08%, 42.7% respectively compared to unheated B100. © 2021 Elsevier LtdItem Effect of variable compression ratio and equivalence ratio on performance, combustion and emission of hydrogen port injection SI engine(Elsevier Ltd, 2022) Pandey, J.K.; Kumar, G.N.The present study includes an experimental investigation of the performance, combustion, and emission parameters of a hydrogen port fueled SI engine under wide-open throttle. The compression ratio (CR) is varied from 10 to 15, equivalence ratio (φ) from 0.4 to 1.0, and speed from 1400RPM to 1800RPM. The ignition timing is maintained at 20° before the top dead center. The brake thermal efficiency increases by nearly 10% from CR10 to CR15, and it also increased by 13.7% by changing φ from 0.4 to 0.9. Similarly, BP increases in the same fashion. The combustion enhances with an increase in peak pressure by increasing CR from 10 to 15 and φ from 0.4 to 0.9; however, φ 1.0 exhibits a negative trend. However, the NOX emission increases continuously with CR and φ, and so as the exhaust gas temperature. The carbon-based emissions are negligible, and volumetric efficiency decreases with φ and increases with CR. © 2021 Elsevier Ltd