Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Conversion of microfiltration membrane into nanofiltration membrane by vapour phase deposition of aluminium for desalination application(2011) Padaki, M.; Isloor, A.M.; Nagaraja, K.K.; Nagaraja, H.S.; Pattabi, M.Preparation and modification of NF membrane are challenging aspects in research. In the present work, we have synthesised Polysulfone (PSf) microfiltration membrane and reduced the pore size to nano level by physical vapour deposition (PVD) of aluminium metal. Membrane pore size was reduced from micro pore to nano pore, which rejected 42.22% of NaCl from the solution with 164L/m2h. And also water permeation decreases from 1.10324-10-10 to the 9.141-10-12. The SEM and AFM pictures showed the surface modification and metal deposition in the pores. The performance of the membrane was studied by dead end flow cell using 3.5% of NaCl solution, in which PVD membrane showed 42.22% of rejection with 16.4L/m2h flux. Thermal analysis from DSC showed Tg of 265°C. Contact angle measurement, and water uptake were also reported. © 2011 Elsevier B.V.Item Preparation, characterization and the effect of PANI coated TiO2 nanocomposites on the performance of polysulfone ultrafiltration membranes(Royal Society of Chemistry, 2015) Pereira, V.R.; Isloor, A.M.; Ahmed, A.A.; A.F., A.F.Polysulfone ultrafiltration (UF) membranes with PANI-TiO2 (polyaniline-titania) nanocomposites and PEG 1000 (Polyethylene Glycol 1000) as additives were prepared by the phase inversion method. PANI-TiO2 nanocomposites were synthesized by coating TiO2 nanotubes with PANI via chemical oxidative polymerization. The synthesized PANI-TiO2 nanocomposite was characterized by Fourier Transform Infrared Spectroscopy (FTIR), X-ray diffraction (XRD) and Transmission Electron Microscope (TEM) analysis. PANI-TiO2 nanocomposites with varying concentrations (0-1.5 wt%) were dispersed in the polysulfone membrane matrix with N-methyl-2-pyrrolidone (NMP) as solvent along with PEG 1000 as the pore former. The effect of addition of PANI-TiO2 nanocomposites with different concentrations (0-1.5 wt%) on the membrane structure, performance, hydrophilicity and the antifouling nature of the membranes was analyzed. PANI-TiO2 nanocomposite membranes showed better hydrophilicity, improved permeability, enhanced porosity, water uptake and good antifouling ability when compared with neat polysulfone membranes. The performance of the membranes improved with the increase in the addition of the PANI-TiO2 nanocomposite. However, the membrane performance decreased slightly at 1.5 wt% addition of PANI-TiO2 due to the agglomeration of PANI-TiO2 at higher concentration. The well performed membranes were also subjected to heavy metal ion rejection. The membranes showed a rejection of 83.75% and 73.41% during the polymer enhanced ultrafiltration (PEUF) process and a rejection of 68% and 53.78% during the UF process for Pb2+ and Cd2+ respectively. © The Royal Society of Chemistry and the Centre National de la Recherche Scientifique 2015.Item Probing the morphology and anti-organic fouling behaviour of a polyetherimide membrane modified with hydrophilic organic acids as additives(Royal Society of Chemistry, 2015) Hebbar, R.S.; Isloor, A.M.; A.F., A.F.; Shilton, S.J.; AlObaid, A.; Fun, H.-K.A facile approach for the preparation of an organic antifouling polymer membrane has been developed using low molecular weight organic acids as additives. The presence of these additives in the membrane was analysed by FTIR spectroscopy. The properties of the modified membranes were investigated in terms of contact angle, water uptake capacity, SEM and AFM analysis. These additives exerted a strong impact on the rheological properties of the casting solution, thereby altering the membrane morphology, surface roughness, water flux and the hydrophilicity of the membranes, as compared to those of the pristine polyetherimide (PEI) membrane. The organic antifouling properties of the modified membrane were analysed by filtering both bovine serum albumin (BSA) and humic acid solutions. The results showed that the additives exhibited a remarkable improvement in the antifouling properties (FRR of 72%) and a humic acid rejection of up to 86%. These outcomes offer new insights into the use of cheaper and readily available organic acids as additives, compared to the traditional, synthetic polymer materials as additives in membrane preparation. ©2015 The Royal Society of Chemistry and the Centre National de la Recherche Scientifique.Item Nisin gold nanoparticles assemble as potent antimicrobial agent against Enterococcus faecalis and Staphylococcus aureus clinical isolates(Editions de Sante editions.de.sante@wanadoo.fr, 2017) Pradeepa, n.; Bhat, K.U.; Vidya, S.M.Enterococci and staphylococci have the potency to acquire resistant to antibiotics and have emerged as serious nosocomial pathogens responsible for various diseases. The continuous seeking of new antimicrobials against these pathogens is the only way to avoid the rapid spreading of diseases. Controlled fabrication of existing antimicrobials with nanoparticles offers an alternative strategy to combat against these pathogens with an effective manner. In the present study, gold nanoparticles (AuNPs) were functionalized with nisin to kill a wide range of clinically isolated Enterococcus faecalis and Staphylococcus aureus strains. Nisin functionalized gold nanoparticles (NAuNPs) exhibited good inhibitory activity against all seven multidrug resistant (MDR) and eight non-MDR E. faecalis and S. aureus strains. Minimum inhibitory concentration of NAuNPs was >8–32 fold lower than nisin. Interestingly, antibiotic resistant was not observed by these pathogens up to 8 generation. TEM and AFM investigation revealed that, the antimicrobial action of NAuNPs appears to act in three sequential stages: membrane destabilization, pore formation, followed by intracellular fluid leakage. In addition, NAuNPs were non toxic and showed less hemolytic activity. These findings indicated that, the NAuNPs can be served as an alternative antimicrobial agent to treat a wide range of enterococcal and staphylococcal infections. © 2016 Elsevier B.V.Item Use of cellulose acetate/polyphenylsulfone derivatives to fabricate ultrafiltration hollow fiber membranes for the removal of arsenic from drinking water(Elsevier B.V., 2019) Kumar, M.; Todeti, S.; Isloor, A.M.; Gnani Peer Mohamed, G.P.S.; Siddique, I.; Ismail, N.I.; A.F., A.F.; Asiri, A.M.Cellulose acetate (CA) and cellulose acetate phthalate (CAP) were used as additives (1 wt%, 3 wt%, and 5 wt%) to prepare polyphenylsulfone (PPSU) hollow fiber membranes. Prepared hollow fiber membranes were characterized by surface morphology using scanning electron microscopy (SEM), surface roughness by atomic force microscopy (AFM), the surface charge of the membrane was analyzed by zeta potential measurement, hydrophilicity by contact angle measurement and the functional groups by fourier transform infrared spectroscopy (FTIR). Fouling resistant nature of the prepared hollow fiber membranes was evaluated by bovine serum albumin (BSA) and molecular weight cutoff was investigated using polyethylene glycol (PEG). By total organic carbon (TOC), the percentage rejection of PEG was found to be 14,489 Da. It was found that the hollow fiber membrane prepared by the addition of 5 wt% of CAP in PPSU confirmed increased arsenic removal from water as compared to hollow fiber membrane prepared by 5 wt% of CA in PPSU. The removal percentages of arsenic with CA-5 and CAP-5 hollow fiber membrane was 34% and 41% with arsenic removal permeability was 44.42 L/m2h bar and 40.11 L/m2h bar respectively. The increased pure water permeability for CA-5 and CAP-5 hollow fiber membrane was 61.47 L/m2h bar and 69.60 L/m2 h bar, respectively. © 2019 Elsevier B.V.Item Solar assisted photocatalytic degradation of organic pollutants in the presence of biogenic fluorescent ZnS nanocolloids(Elsevier Ltd, 2019) Uddandarao, P.; Hingnekar, T.A.; Mohan Balakrishnan, R.M.; Rene, E.R.The main aim of this study was to ascertain the photocatalytic degradation of organic pollutants present in aqueous phase using fluorescent biogenic ZnS nanocolloids produced from an endophytic fungus Aspergillus flavus. The degradation studies were carried out using different organic pollutants such as methyl violet (MV), 2,4-dichlorophenoxyacetic acid (2,4-D) and paracetamol (PARA) for 120 min, 270 min and 240 min, respectively, at pH varying from 3.0 to 11.0. The results from this study indicate that the degradation efficiency of ZnS nanocolloids for MV, 2,4-D and PARA were 87%, 33% and 51%, respectively, at the optimum concentration of 100 mg/L of the tested organic pollutants. At different time intervals, the samples were analyzed for their chemical oxygen demand (COD) and total organic carbon (TOC) contents. The reduction of COD and TOC were 78% and 74% for MV at 120 min; 55.5% and 57.2% for 2,4-D at 270 min and 47.6% and 44.5% for PARA at 240 min, respectively. The degradation pathway was determined based on the mass spectrum and the intermediates formed; in addition, the interaction between organic pollutants and nanocolloids was also elucidated based on atomic force microscopy (AFM) and fluorescence spectrum. © 2019 Elsevier LtdItem Reactive magnetron sputtered–assisted deposition of nanocomposite thin films with tuneable magnetic, electrical and interfacial properties(Springer Science and Business Media B.V. editorial@springerplus.com, 2020) Ratnesh, R.K.; Singh, M.; Pathak, S.; Dakulagi, V.In this work, different magnetic thin films of Ni, NiFe and NiFe2O4 are deposited on the SiO2 substrate using sputtering technique. Our experiments confirmed that thin films possess a good nanocrystalline structure. The key deposition parameters controlling their magnetic properties are sheet resistivity, crystalline structure and microtopography of the sputtered thin film. Besides, the reactive gas oxygen (O2) also plays a leading role in transforming the phase and structure of the ferrite film. The nanocrystalline nature of the ferrite film results in the reduction of overall coercivity (HC). The thickness of the sputtered thin film is in the range of 800–1000 Å. The prepared film exhibits roughness in the range of (~ 0.60 to ~ 0.98 nm). Furthermore, the structural transformation study is performed with X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The quite low roughness, high resistivity and low Hc make NiFe2O4 thin film as a potential candidate for the future spintronics, optoelectronics, photocatalysis and solar cell applications. © 2020, Springer Nature B.V.Item Evaluation of the surface characteristics and antibacterial properties of Titanium dioxide nanotube and methacryloyloxyethylphosphorylcholine (MPC) coated orthodontic brackets-a comparative invitro study(Springer Science and Business Media Deutschland GmbH, 2024) Rao, M.; Ashith, M.V.; Suman, E.; Isloor, A.M.; Shetty, N.J.; Srikant, S.Objectives: White spot lesions are the most common iatrogenic effect observed during orthodontic treatment. This study aimed to compare the surface characteristics and antibacterial action of uncoated and coated orthodontic brackets. Materials and methods: Sixty commercially available stainless steel brackets were coated with TiO2 nanotubes and methacryloyloxyethylphosphorylcholine. The sample was divided into Group 1: uncoated orthodontic brackets, Group 2: Stainless steel brackets with TiO2 nanotubes coating, Group 3: Stainless steel brackets with methacryloyloxyethylphosphorylcholine coating, and Group 4: Stainless steel brackets with TiO2 nanotubes combined with methacryloyloxyethylphosphorylcholine coating. Surface characterization was assessed using atomic force microscopy and scanning electron microscopy. Streptococcus mutans was selected to test the antibacterial ability of the orthodontic brackets, total bacterial adhesion and bacterial viability were assessed. The brackets were subjected to scanning electron microscopy to detect the presence of biofilm. Results: The surface roughness was the greatest in Group 1 and least in Group 2 followed by Group 4 and Group 3 coated brackets. The optical density values were highest in Group 1 and lowest in Group 4. Comparison of colony counts revealed high counts in Group 1 and low counts in Group 4. A positive correlation between surface roughness and colony counts was obtained, however, was not statistically significant. Conclusions: The coated orthodontic brackets exhibited less surface roughness than the uncoated orthodontic brackets. Group 4 coated orthodontic brackets showed the best antibacterial properties. Clinical relevance: Coated orthodontic brackets prevent adhesion of streptococcus mutans and reduces plaque accumulation around the brackets thereby preventing formation of white spot lesions during orthodontic treatment. © The Author(s) 2024.