Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
90 results
Search Results
Item [No abstract available](Springer Netherlands, Low cycle fatigue behavior of an (? + ?) titanium alloy) Nanjundaswamy, G.S.; Ramachandra, C.; Sengupta, P.K.; Chatterji, B.; Sudhakara Nayak, H.V.; Singh, A.K.1998Item Compression testing of Ti-6Al-4V in the temperature range of 303-873 K(2008) Srinivasan, K.; Venugopal, P.Compression testing of Ti-6Al-4V alloy has been carried out at temperatures between 303 K to 873 K. To prevent embrittlement due to atmospheric oxygen and nitrogen, the samples were given a glass coating, which also acts as a lubricant simultaneously. Dynamic Strain Aging was observed to occur in the temperature range of 600 K to 800 K. Below 600 K stresses were high. Warm working has to be done above 800 K but below 1163 K (0.6 Tm where Tm = 1940 K) which is the recrystallization temperature. Based on these conclusions, warm extrusion has been successfully carried out in the Materials Forming Laboratory of I.I.T., Madras, Chennai, India.Item Effect of mushy state rolling on age-hardening and tensile behavior of Al-4.5Cu alloy and in situ Al-4.5Cu-5TiB2 composite(Elsevier Ltd, 2011) Siddhalingeshwar, I.G.; Herbert, M.A.; Chakraborty, M.; Mitra, R.The effect of mushy state rolling on aging kinetics of stir-cast Al-4.5Cu alloy and in situ Al-4.5Cu-5TiB2 composite and their tensile behavior in solution-treated (495°C) or differently aged (170°C) conditions, has been investigated. As-cast or pre-hot rolled alloy and composite samples were subjected to single or multiple mushy state roll passes to 5% thickness reduction at temperatures for 20% liquid content. Peak-aging times of mushy state rolled composite matrices have been found as ?7.5-10% of that of as-cast alloy. Such enhancement in aging kinetics is attributed to homogeneity in Cu atom distribution as well as increase in matrix dislocation density due to thermal expansion coefficient mismatch between Al and TiB2, matrix grain refinement and particle redistribution, achieved by mushy state rolling. Uniform precipitate distribution in mushy state rolled composite matrices leads to greater peak-age microhardness with higher yield and ultimate tensile strengths than those in as-cast alloy and composite. © 2010 Elsevier B.V.Item A review on machining of titanium based alloys using EDM and WEDM(Institute of Problems of Mechanical Engineering mpm@def.ipme.ru, 2014) Manjaiah, M.; Narendranath, S.; Basavarajappa, S.The aim of this review is to present the consolidated information about the contributions of various researchers on the application of EDM and WEDM on titanium materials and subsequently identify the research gaps. The literature survey has been carried out from three perspectives such as application of EDM and WEDM on titanium materials, utilization of tools and techniques for correlating experimental results and application of products produced by EDM and WEDM. Three main research areas has been identified. First, the application of EDM and WEDM on titanium materials mainly TiNi based alloys. Second, the utilization of advanced tools and techniques such as artificial neural network (ANN), advanced particle swarm optimization (PSO) and tabu enhanced genetic algorithm (GA). Third, the study and analysis of surface integrity in EDM and WEDM on titanium materials. In addition, the paper has also evolved the future research directions. The paper has been concluded by indicating the future research directions for the research gaps identified during this literature survey.Item Wire electric discharge machining characteristics of titanium nickel shape memory alloy(Nonferrous Metals Society of China B12 Fuxing Road Beijing 100814, 2014) Manjaiah, M.; Narendranath, S.; Basavarajappa, S.; Gaitonde, V.N.TiNi shape memory alloys (SMAs) have been normally used as the competent elements in large part of the industries due to outstanding properties, such as super elasticity and shape memory effects. However, traditional machining of SMAs is quite complex due to these properties. Hence, the wire electric discharge machining (WEDM) characteristics of TiNi SMA was studied. The experiments were planned as per L27 orthogonal array to minimize the experiments, each experiment was performed under different conditions of pulse duration, pulse off time, servo voltage, flushing pressure and wire speed. A multi-response optimization method using Taguchi design with utility concept has been proposed for simultaneous optimization. The analysis of means (ANOM) and analysis of variance (ANOVA) on signal to noise (S/N) ratio were performed for determining the optimal parameter levels. Taguchi analysis reveals that a combination of 1 ?s pulse duration, 3.8 ?s pulse off time, 40 V servo voltage, 1.8×105 Pa flushing pressure and 8 m/min wire speed is beneficial for simultaneously maximizing the material removal rate (MRR) and minimizing the surface roughness. The optimization results of WEDM of TiNi SMA also indicate that pulse duration significantly affects the material removal rate and surface roughness. The discharged craters, micro cracks and recast layer were observed on the machined surface at large pulse duration.Item Analysis of surface roughness and hardness in titanium alloy machining with polycrystalline diamond tool under different lubricating modes(Universidade Federal de Sao Carlos, 2014) Revankar, G.D.; Shetty, R.; Rao, S.S.; Gaitonde, V.N.The present work deals with the investigation on machining of difficult-to-machine material titanium alloy (Ti-6Al-4V) using poly crystalline diamond (PCD) tool under different coolant strategies, namely dry, flooded and MQL. Taguchi technique has been employed and the optimization results indicated that MQL lubricating mode with cutting speed of 150 m/min, feed rate of 0.15 mm/rev, nose radius of 0.6 mm and 0.25 mm depth of cut is necessary to minimize surface roughness and dry mode with cutting speed of 150 m/min, feed rate of 0.15 mm/rev, nose radius of 0.6 mm and 0.75 mm depth of cut is necessary to maximize surface hardness. The results indicate the substantial benefit of the minimum quantity of lubrication (MQL) and justify PCD inserts to be the most functionally satisfactory commercially available cutting tool material for machining titanium alloys for better surface finish and hardness.Item Selection of optimal process parameters in ball burnishing of titanium alloy(Taylor and Francis Inc. 325 Chestnut St, Suite 800 Philadelphia PA 19106, 2014) Revankar, G.D.; Shetty, R.; Rao, S.S.; Gaitonde, V.N.The current study deals with the analysis and optimization of the ball burnishing process of titanium alloy (Ti-6Al-4V). The Taguchi method was employed to determine the best combination of ball burnishing process parameters - such as burnishing speed, burnishing feed, burnishing force and number of passes - to minimize surface roughness and maximize hardness. The dry burnishing experiments were planned as per L9 orthogonal array (OA,) and signal-to-noise (S/N) ratio was applied to measure the proposed performance characteristics. Analysis of means (ANOM) and analysis of variance (ANOVA) were carried out to evaluate the optimal levels and to obtain the level of importance of the burnishing parameters, respectively. Validation tests with optimal levels of parameters were performed to illustrate the effectiveness of Taguchi optimization. The optimization results revealed that burnishing feed and burnishing force are the significant parameters for minimizing the surface roughness, whereas number of passes and burnishing force play important roles in maximizing the hardness. © 2014 Taylor & Francis Group, LLC.Item Analysis of surface roughness and hardness in ball burnishing of titanium alloy(Elsevier B.V., 2014) Revankar, G.D.; Shetty, R.; Rao, S.S.; Gaitonde, V.N.Ball burnishing is a popular post-machining metal finishing operation. An attempt has been made in this paper to optimize the process parameters during burnishing of titanium alloy (Ti-6Al-4V). Ball burnishing process parameters such as burnishing speed, burnishing feed, burnishing force and number of passes were considered to minimize the surface roughness and maximize the hardness. The lubricated ball burnishing experiments were planned as per L25 orthogonal array and signal to noise (S/N) ratio was applied to measure the proposed performance characteristics. The validation tests with the optimal levels of parameters were performed to illustrate the effectiveness of Taguchi optimization. The optimization results revealed that burnishing feed and burnishing speed are the significant parameters for minimizing the surface roughness, whereas burnishing force and number of passes play important roles in maximizing the hardness. The optimization results showed greater improvements in surface finish (77%) and hardness (17%) when compared to pre-machined surfaces. © 2014 Elsevier Ltd. All rights reserved.Item Effect of combined grain refinement and modification on microstructure and mechanical properties of hypoeutectic, eutectic and hypereutectic Al-Si alloys(Inderscience Publishers, 2015) Shivaprasad, C.G.; Kiran Aithal, K.; Narendranath, S.; Desai, V.; Mukunda, P.G.The effect of melt treatment owing to the combined addition of grain refiner and modifier on the microstructure and mechanical properties of Al-Si alloys having 7% (hypoeutectic), 12% (eutectic) and 15% silicon (hypereutectic) is studied. 1 wt. % of Al-1Ti-3B Master alloy was used as grain refiner. For modification of eutectic Si, 0.2 wt. % of Al-10Sr Master alloy was added to hypoeutectic alloy and 0.4 wt. % is added to eutectic alloy as well as hypereutectic alloy. Furthermore, refinement of primary Si in hypereutectic alloy was achieved by addition of 0.04 wt. % of phosphorus. The goal of this investigation is to determine the influence of combined addition of grain refiner and modifier on mechanical properties and qualitatively correlate with the microstructural changes. © 2015 Inderscience Enterprises Ltd.Item Effect of electrode material in wire electro discharge machining characteristics of Ti50Ni50-xCux shape memory alloy(Elsevier Inc. usjcs@elsevier.com, 2015) Manjaiah, M.; Narendranath, S.; Basavarajappa, S.; Gaitonde, V.N.Abstract TiNiCu alloy belongs to new class of shape memory alloy (SMA), which exhibits superior properties like shape memory effect, super elasticity and reversible martensitic transformation phase and thus find broad applications in actuators, micro tools and stents in biomedical components. Even though, SMA demonstrates outstanding property profile, traditional machining of SMAs is fairly complex and hence non-traditional machining like wire electric discharge machining (WEDM) has been performed. Hence, there is a need to investigate the WEDM performance characteristics of shape memory alloys due to excellent property profile and potential applications. In the present investigation, various machining characteristics like material removal rate (MRR), surface roughness, surface topography and metallographic changes have been studied and the influence of wire material on TiNiCu alloy machining characteristics has also been evaluated through ANOVA. Ti50Ni50-xCux=10, 20 was prepared by vacuum arc melting process. The proposed alloy as-cast material exhibits austenite property (B2 phase) and having higher hardness when compared to TiNi alloy. The investigation on WEDM of Ti50Ni50-xCux alloy reveals that the machining parameters such as servo voltage, pulse on time and pulse off time are the most significant parameters affecting MRR as well as surface roughness using both brass and zinc coated brass wires. However, machining with zinc coated brass wire yields reduced surface roughness and better MRR and also produces less surface defects on the machined surface of Ti50Ni50-xCux alloys. © 2015 Elsevier Inc. All rights reserved.