Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
41 results
Search Results
Item Magnetic property and corrosion resistance of electrodeposited nanocrystalline iron-nickel alloys(Elsevier B.V., 2012) Pavithra, G.P.; Hegde, A.In the present investigation we have galvanostatically synthesized nanocrystalline Fe-Ni alloys on copper substrate. The effect of current density (c.d.) on composition, surface morphology and phase structure were studied for explaining the magnetic and electrochemical properties of the nanocrystalline alloy. The bath found to exhibit the preferential deposition of less noble Fe than Ni, and at no conditions of c.d., the deposition has changed from anomalous to normal type. Surface morphology and structural characteristics of the deposits were examined using scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. As composition of the alloy varied, consequent to the current density a change of body centered cubic structure (bcc) to face centered cubic structure (fcc) was observed for nanocrystalline materials. Finally, the conditions responsible for peak magnetic property and corrosion resistance were optimized. Factors responsible for improved functional properties were explained in terms of surface morphology and crystalline grain size of the coatings. © 2012 Elsevier B.V.Item Glass fiber-supported NiO nanofiber webs for reduction of CO and hydrocarbon emissions from diesel engine exhaust(Cambridge University Press, 2014) George, G.; Anandhan, S.In this study, nickel acetate tetrahydrate (NACTH)/poly(styrene-co-acrylonitrile) (SAN) sol was used for the fabrication of nanocrystalline NiO nanofibers. An indigenous setup was developed to use these nanofibers for the oxidation of carbon monoxide (CO) and unburnt hydrocarbons (HC) from diesel engine exhaust. The morphological, compositional, and crystalline properties of the NiO nanofibers obtained after calcination were studied by scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy, and x-ray diffraction (XRD). Clear evidence of defects in the fibers was observed in ultraviolet-visible-near infrared (UV-Vis-NIR) spectra, Raman spectra, and magnetic property measurements. The NiO nanofiber mats supported by glass fiber mats were efficient in oxidizing CO and HC from diesel engine exhaust, and the maximum efficiency was achieved by using NiO nanofibers with the maximum amount of defects. © © Materials Research Society 2014.Item Glass fiber-supported NiO nanofiber webs for reduction of CO and hydrocarbon emissions from diesel engine exhaust(Cambridge University Press, 2014) George, G.; Anandhan, S.In this study, nickel acetate tetrahydrate (NACTH)/poly(styrene-co-acrylonitrile) (SAN) sol was used for the fabrication of nanocrystalline NiO nanofibers. An indigenous setup was developed to use these nanofibers for the oxidation of carbon monoxide (CO) and unburnt hydrocarbons (HC) from diesel engine exhaust. The morphological, compositional, and crystalline properties of the NiO nanofibers obtained after calcination were studied by scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy, and x-ray diffraction (XRD). Clear evidence of defects in the fibers was observed in ultraviolet-visible-near infrared (UV-Vis-NIR) spectra, Raman spectra, and magnetic property measurements. The NiO nanofiber mats supported by glass fiber mats were efficient in oxidizing CO and HC from diesel engine exhaust, and the maximum efficiency was achieved by using NiO nanofibers with the maximum amount of defects. © © Materials Research Society 2014.Item Molecular Engineering and Theoretical Investigation of Novel Metal-Free Organic Chromophores for Dye-Sensitized Solar Cells(Elsevier Ltd, 2015) Babu, D.D.; Cheema, H.; Elsherbiny, D.; El-Shafei, A.; Vasudeva Adhikari, A.V.In this work we report design and synthesis of three new metal free D-D-A-?-A type dyes (E1-3) with different acceptor/anchoring groups, as effective sensitizers for nanocrystalline titanium dioxide based dye sensitized solar cells. All the three dyes carry electron donating methoxy group as an auxiliary and indole as a principal donor, cyanovinylene as an auxiliary acceptor and thiophene as a ?-spacer. Whereas, cyanoacetic acid, rhodanine-3-acetic acid and 4-aminobenzoic acid perform as acceptor/anchoring moieties, respectively in the dyes E1-3. Though the dye containing 4-aminobenzoic acid unit (E3) exhibits comparatively lower ?max, it shows the highest power conversion efficiency arising from the higher electron life time and good light-harvesting capability. The DFT studies reveal a better charge separation between the HOMO and LUMO levels of E3, further substantiating the experimental results. Among the three dyes, E3 shows the best photovoltaic performance with short-circuit current density (Jsc) of 9.35 mA cm-2, open-circuit voltage (Voc) of 620 mV and fill factor (FF) of 0.71, corresponding to an overall conversion efficiency of 4.12% under standard global AM 1.5G. © 2015 Elsevier Ltd. All rights reserved.Item Nonlinear transmittance and optical power limiting in magnesium ferrite nanoparticles: effects of laser pulsewidth and particle size(Royal Society of Chemistry, 2016) Perumbilavil, S.; Sridharan, K.; Abraham, A.R.; Janardhanan, H.P.; Kalarikkal, N.; Philip, R.We report comparative measurements of size dependent nonlinear transmission and optical power limiting in nanocrystalline magnesium ferrite (MgFe2O4) particles excited by short (nanosecond) and ultrashort (femtosecond) laser pulses. A standard sol-gel technique is employed to synthesize particles in the size range of 10-50 nm, using polyvinyl alcohol as the chelating agent. The structure and morphology of the samples are studied using X-ray diffraction, scanning electron microscopy and transmission electron microscopy. Growth of the particles in time is tracked through Fourier transform infrared spectroscopy. Nonlinear transmission measurements have been carried out using the open aperture Z-scan technique employing 532 nm, 5 nanosecond pulses and 800 nm, 100 femtosecond pulses, respectively. The measured optical nonlinearity is primarily of a reverse saturable absorption (RSA) nature, arising mostly from excited state absorption for nanosecond excitation, and two-photon absorption for femtosecond excitation. The optical limiting efficiency is found to increase with particle size for both cases. The calculated nonlinear parameters indicate that these materials are potential candidates for optical limiting applications. © The Royal Society of Chemistry.Item ZnS semiconductor quantum dots production by an endophytic fungus Aspergillus flavus(Elsevier Ltd, 2016) Uddandarao, P.; Mohan B, R.The development of reliable and eco-friendly processes for the synthesis of metal sulphide quantum dots has been considered as a major challenge in the field of nanotechnology. In the present study, polycrystalline ZnS quantum dots were synthesized from an endophytic fungus Aspergillus flavus. It is noteworthy that apart from being rich sources of bioactive compounds, endophytic fungus also has the ability to mediate the synthesis of nanoparticles. TEM and DLS revealed the formation of spherical particles with an average diameter of about 18 nm and 58.9 nm, respectively. The ZnS quantum dots were further characterized using SEM, EDAX, XRD, UV-visible spectroscopy and FTIR. The obtained results confirmed the synthesis of polycrystalline ZnS quantum dots and these quantum dots are used for studying ROS activity. In addition this paper explains kinetics of metal sorption to study the role of biosorption in synthesis of quantum dots by applying Morris-Weber kinetic model. Since Aspergillus flavus is isolated from a medicinal plant Nothapodytes foetida, quantum dots synthesized from this fungus may have great potential in broad environmental and medical applications. © 2016 Elsevier B.V. All rights reserved.Item Fabrication, characterization and catalytic activity of ?-MnO2 nanowires for dye degradation of reactive black 5(Elsevier B.V., 2016) Ramesh, M.; Nagaraja, H.S.; Rao, M.P.; Anandan, S.; Huang, N.M.?-MnO2 nanowires (NWs) prepared by hydrothermal method are characterized using XRD and FT-IR. The crystallite size, surface area of NWs increases, whereas dislocation density and band gap decreases with an increase in oxidizer molarity. The band gap decreases from 2.55 to 1.27 eV. The above observations correlate well with the enhanced catalytic activity of MnO2 NWs for degradation of azo dye reactive black 5 (RB5). About 70% of the dye were successfully removed in 60 min using 20 mg of MnO2 NWs in the presence of 6 mL of H2O2. MnO2 NWs show a good reusability, suggesting it as an effective and recyclable catalyst. © 2016 Elsevier B.V. All rights reserved.Item Microstructural characterization of low temperature plasma-nitrided 316L stainless steel surface with prior severe shot peening(Elsevier Ltd, 2016) Jayalakshmi, M.; Huilgol, P.; Badekai Ramachandra, B.R.; Bhat, K.U.Surface nanocrystallization by severe deformation has proven beneficial as pre-treatment to plasma nitriding. It aids in achieving thicker nitride layers at lower temperatures thus making the process more economical. In austenitic stainless steels, severe deformation leads to formation of strain induced martensite on the surface while plasma nitriding alone forms expanded austenite. However, structural characteristics of surface layer of pre-deformed steel after plasma nitriding is still a matter of debate. In present study, 316L stainless steel was subjected to severe shot peening: followed by plasma nitriding at 400 °C for 4 h. Characteristics of sample surface before and after treatment were analyzed by scanning electron microscopy, X-ray diffractometry and transmission electron microscopy techniques. Results showed that, this duplex treatment leads to formation of about 45 ?m thick nitride layer; without CrN precipitation. This is significantly high compared to reported data considering the temperature and duration of nitriding treatment employed. Selected area electron diffraction pattern from topmost surface confirmed the co-existence of austenite and martensite while subsurface layer was predominantly consisting of lath martensite. This indicates that major phase in the nitrided layer is martensitic in nature and nitrogen supersaturation leads to transformation of small fraction of martensite to expanded austenite. © 2016 Elsevier LtdItem Effect of shot peening coverage on surface nanostructuring of 316L stainless steel and its influence on low temperature plasma-nitriding(ASTM International, 2017) Jayalakshmi, M.; Badekai Ramachandra, B.; Bhat, K.U.Air-blast shot peening (ABSP) is a cost effective and industrially viable technique to produce nanostructured surface layer on metallic materials. In the present study, 316L stainless steel samples were subjected to shot peening at different peening coverage, from conventional to severe peening. Nanocrystalline structure was observed on the sample surface after peening and mechanical twins; intersection of multidirectional twins producing rhombic blocks were observed in the subsurface layer. Peening process led to the formation of strain induced martensite (?'), and its fraction was found to increase with the coverage. Depth of nanostructured layer and surface microhardness also increased with the increase in coverage, whereas surface roughness followed an opposite trend. Both peened and un-peened samples were subjected to plasma nitriding at 400°C for 4 h. Uniform and appreciably high case depth of about 45 ?m was observed in severely pre-peened (1000 % coverage) sample after nitriding treatment. No precipitation of CrN was observed. This highlights the marked influence of severe shot peening as a pre-treatment for low temperature plasma nitriding of austenitic stainless steels. © © 2017 by ASTM International.Item Additive manufacturing of an aluminum matrix composite reinforced with nanocrystalline high-entropy alloy particles(Elsevier Ltd, 2017) Karthik, G.M.; Panikar, S.; Janaki Ram, G.D.J.; Kottada, R.S.In the present work, a metal-metal composite consisting of aluminum-magnesium alloy AA5083 matrix and nanocrystalline CoCrFeNi high-entropy alloy reinforcement particles in 12 vol% was successfully friction deposited in multiple layers. The layer interfaces or the reinforcement/matrix interfaces showed no brittle intermetallic formation – thanks to the inert nature as well as the high strength and hardness of the high-entropy alloy reinforcement particles. The composite showed significantly higher tensile and compressive strengths as compared to standard wrought-processed alloy AA5083-H112 and offered a much better combination of strength and ductility when compared to conventional aluminum matrix composites reinforced with ceramic particles. The current study establishes friction deposition as a viable technique for additive manufacturing of novel high-performance composite materials. © 2016 Elsevier B.V.