Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
39 results
Search Results
Item Defence applications of polymer nanocomposites(Defense Scientific Information and Documentation Centre, 2010) Kurahatti, R.V.; Surendranathan, A.O.; Kori, S.A.; Singh, N.; Kumar, A.V.R.; Srivastava, S.The potential opportunities promised by nanotechnology for enabling advances in defence technologies are staggering. Although these opportunities are likely to be realised over a few decades, many advantages are currently being explored, particularly for defence applications. This review provides an insight into the capabilities offered by nanocomposites which include smart materials, harder/lighter platforms, new fuel sources and storage as well as novel medical applications. It discusses polymer-based nanocomposite materials, nanoscale fillers and provides examples of the actual and potential uses of nanocomposite materials in defence with practical examples. © 2010, DESIDOC.Item ZnS semiconductor quantum dots production by an endophytic fungus Aspergillus flavus(Elsevier Ltd, 2016) Uddandarao, P.; Mohan B, R.The development of reliable and eco-friendly processes for the synthesis of metal sulphide quantum dots has been considered as a major challenge in the field of nanotechnology. In the present study, polycrystalline ZnS quantum dots were synthesized from an endophytic fungus Aspergillus flavus. It is noteworthy that apart from being rich sources of bioactive compounds, endophytic fungus also has the ability to mediate the synthesis of nanoparticles. TEM and DLS revealed the formation of spherical particles with an average diameter of about 18 nm and 58.9 nm, respectively. The ZnS quantum dots were further characterized using SEM, EDAX, XRD, UV-visible spectroscopy and FTIR. The obtained results confirmed the synthesis of polycrystalline ZnS quantum dots and these quantum dots are used for studying ROS activity. In addition this paper explains kinetics of metal sorption to study the role of biosorption in synthesis of quantum dots by applying Morris-Weber kinetic model. Since Aspergillus flavus is isolated from a medicinal plant Nothapodytes foetida, quantum dots synthesized from this fungus may have great potential in broad environmental and medical applications. © 2016 Elsevier B.V. All rights reserved.Item Solid state amorphization of Mg-Zn-Ca system via mechanical alloying and characterization(Elsevier B.V., 2017) Manne, B.; Bontha, S.; Ramesh, M.R.; Krishna, M.; Balla, V.K.Magnesium based bulk metallic glasses have attracted significant attention of researchers due to better mechanical and corrosion properties when compared to their crystalline counterparts especially for biomedical applications. Scaling up the part size and production volumes of such materials through liquid metallurgy route is challenging. In this work amorphous Ca5Mg60+xZn35?x (X = 0, 3 and 7) alloys have been successfully synthesized through solid state amorphization using a high energy planetary ball mill. X-ray diffraction was used to identify the crystalline phases of the powder during reaction. Evolution of amorphous phase was analysed using a parameter involving the ratio of integral area of peaks to the integral area of background (IPB) obtained from XRD patterns. Results showed reaction time increases with decreasing Zn content in Ca5Mg60+xZn35?x (X = 0, 3 and 7) alloy to obtain maximum amorphous structure with a small amount of residual crystalline phase. Prolonged milling of these powders, to eliminate residual crystalline phases, resulted in the nucleation of Mg102.08Zn39.6 phase. The composition dependent characteristic temperatures and thermal stabilities were studied using differential scanning calorimetry. © 2016 The Society of Powder Technology JapanItem Corrosion resistance and in-vitro bioactivity of BaO containing Na2O-CaO-P2O5 phosphate glass-ceramic coating prepared on 316 L, duplex stainless steel 2205 and Ti6Al4V(Institute of Physics Publishing helen.craven@iop.org, 2018) Edathazhe, A.B.; Shashikala, H.D.The phosphate glass with composition 11Na2O-15BaO-29CaO-45P2O5 was coated on biomedical implant materials such as stainless steel 316 L, duplex stainless steel (DSS) 2205 and Ti6Al4V alloy by thermal enamelling method. The structural properties and composition of glass coated substrates were studied by x-ray diffraction (XRD), Scanning electron microscopy (SEM) and Energy dispersive x-ray spectroscopy (EDS) analysis. The coatings were partially crystalline in nature with porous structure and pore size varied from micro to nanometer range. The polarization curve was obtained for uncoated and coated substrates from electrochemical corrosion test which was conducted at 37 °C in Hank's balanced salt solution (HBSS). The corrosion resistance of 316 L substrate increased after coating, whereas it decreased in case of DSS 2205 and Ti6Al4V. The XRD and SEM/EDS studies indicated the bioactive hydroxyapatite (HAp) layer formation on all the coated surfaces after electrochemical corrosion test, which improved the corrosion resistance. The observed electrochemical corrosion behavior can be explained based on protective HAp layer formation, composition and diffusion of ions on glass coated surfaces. The in-vitro bioactivity test was carried out at 37 °C in HBS solution for 14 days under static conditions for uncoated and coated substrates. pH and ion release rate measurements from the coated samples were conducted to substantiate the electrochemical corrosion test. The lower ion release rates of Na+ and Ca2+ from coated 316 L supported its higher electrochemical corrosion resistance among coated samples. Among the uncoated substrates, DSS showed higher electrochemical corrosion resistance. Amorphous calcium-phosphate (ACP) layer formation on all the coated substrates after in-vitro bioactivity test was confirmed by XRD, SEM/EDS and ion release measurements. The present work is a comparative study of corrosion resistance and bioactivity of glass coated and uncoated biomedical implants such as 316 L, DSS and Ti6Al4V. © 2018 IOP Publishing Ltd.Item Surface design of Mg-Zn alloy temporary orthopaedic implants: Tailoring wettability and biodegradability using laser surface melting(Elsevier B.V., 2018) Manne, B.; Thiruvayapati, H.; Bontha, S.; Motagondanahalli Rangarasaiah, R.; Das, M.; Balla, V.K.Magnesium-based alloys have attracted significant attention for biomedical applications due to its biodegradability as well as density and elastic modulus which are close to those of human bone. However, the uncontrolled biodegradation and hydrogen evolution are of major concern. In this work, laser surface melting (LSM) has been carried out to tailor initial corrosion rates of Mg-2.2Zn alloy implants. Melt pool dimensions, microstructure and surface topography of the LSM samples were analysed. The wettability and in vitro degradation characteristics of untreated and treated alloy were compared. LSM resulted in much finer cellular microstructural features than as-cast alloy and the melted region depths between 65 and 115 ?m. Higher treatment depths helped to extend the corrosion protection time by suppressing the corrosion front movement. Polished LSM samples resulted in overall corrosion rates of 0.5–0.62 mm/year which was about 40%–50% reduction compared to the as-cast alloy. Accelerated biomineralisation of the surface via enhancements in the surface energy due to microstructural refinement as well as microstructural homogeneity and Zn enrichment in ?-Mg, favoured improvement of the overall corrosion performance of LSM-treated alloy. © 2018 Elsevier B.V.Item Effect of zinc and rare-earth element addition on mechanical, corrosion, and biological properties of magnesium(Cambridge University Press, 2018) Kottuparambil, R.R.; Bontha, S.; Ramesh, M.R.; Arya, S.; Jana, A.; Das, M.; Balla, V.K.; Amrithalingam, S.; Prabhu, T.R.The present work aims to understand the effect of zinc and rare-earth element addition (i.e., 2 wt% Gd, 2 wt% Dy, and 2 wt% of Gd and Nd individually) on the microstructure evolution, mechanical properties, in vitro corrosion behavior, and cytotoxicity of Mg for biomedical application. The microstructure results indicate that the Mg-Zn-Gd alloy consists of the lamellar long period stacking ordered phase. The electrochemical and immersion corrosion behavior were studied in Hanks balanced salt solution. Enhanced corrosion resistance with reduced hydrogen evolution volume and magnesium (Mg2+) ion release were estimated for the Mg-Zn-Gd alloy as compared to the other two alloy systems. At the early stage of corrosion, formation of the oxide film inhibited the corrosion propagation. However, at the later stages, the breaking of the oxide film leads to shallow pitting mode of corrosion. The ultimate tensile strength of Mg-Zn-Gd-Nd is better than the other two alloys due to the uniform distribution of the Mg12Nd precipitate phase. The moderate strength in the Mg-Zn-Gd alloy is due to the low volume fraction of the secondary phase. The MTT (methylthiazoldiphenyl-tetrazolium bromide) assay study was carried out to understand the cell cytotoxicity on the alloy surfaces. Studies revealed that all three alloys had significant cellular adherence and no adverse effect on cells. © 2018 Materials Research Society.Item Experimental Investigation on Effects of Wire Electro Discharge Machining of Ti50Ni45Co5 Shape Memory Alloys(Springer Netherlands rbk@louisiana.edu, 2018) Soni, H.; Narendranath, S.; Ramesh, M.R.TiNiCo shape memory alloy is most popular shape memory alloy for biomedical applications due to their outstanding properties such as shape memory effect, pseudoelasticity and transformation temperature. Machining of such kind of alloys is very difficult through conventional machining process is very difficult because they may affect their internal properties of these alloys. However conventional machining processes give poor surface quality during the machining hence non-conventional machining processes such as (wire electro discharge machining, water jet machining and electro discharge machining etc.) are more suitable for machining of such kind of alloy. From the literature it has been found that Wire electro discharge machining (WEDM) is more suitable non-conventional machining process for such kind of alloy. Present study exhibits the effects WEDM characteristics of Ti50Ni45Co5 shape memory alloy. L-9 orthogonal array has been created by using Taguchi as a design method for machining of selected alloy and machined surface characterization has been carried out at the optimized process parameters with respect to microstructures, surface topography, microhardness, XRD analysis and residual stresses. To find the optimum setting of the input process parameters a couple of optimization techniques are used, namely principal component analysis (PCA) and Gray relational analysis (GRA) technique. 125?s pulse on time (Ton), 35?s pulse off time (Toff) and 40V servo voltage (SV) were found as an optimal setting for the higher material removal rate (MRR) with better surface roughness (SR) in the present study. Moreover, characterization of the machined surface is performed with respect to microstructures, surface topography, microhardness analysis, XRD and residual stresses. Harder surface observed near the cutting edge and TiNio3 Tio2 and CuZn were noticed on the surface of machined component through XRD analysis. However, compressive residual stress has been noticed on the machined surface during WEDM process. © 2018, Springer Science+Business Media B.V., part of Springer Nature.Item Laser surface modification of Mg-Zn-Gd alloy: Microstructural, wettability and in vitro degradation aspects(Institute of Physics Publishing helen.craven@iop.org, 2018) Rakesh, K.R.; Bontha, S.; Ramesh, M.R.; Arya, S.; Das, M.; Balla, V.K.; Srinivasan, A.Mg-Zn-Gd have great potential for biomedical applications owing to excellent bioactivity and non-toxicity properties. In the present study, laser surface melting (LSM) was carried out on newly developed Mg-1Zn -2Gd (wt%) alloy. Effects of laser energy on microstructural evolution, corrosion properties, surface energy, and hardness have been investigated. The surface modified sample processed at different energy densities showed fine grain structure in the melt zone compared to the untreated substrate. Grain refinement in the laser melted region improved the hardness by 60%. The surface roughness was found to be increased with increasing laser energy density. At higher energy density, removal of materials from the surface is enhanced, resulting in deeper grooves and higher surface roughness. The wettability studies indicated that the variations in surface geometry, grain size and surface roughness of LSM samples strongly influence the surface energy and hydrophilicity. Improved wetting of LSM sample was achieved owing to grain refinement and low surface roughness. The corrosion resistance determined by immersion and electrochemical methods of laser melted sample in Hank's balanced salt solution improved considerably due to grain refinement, meltpool depth and uniform distribution of secondary phases. © 2018 IOP Publishing Ltd.Item Performance evaluation of mechanical micro-drilling, electrical discharge machining and laser beam machining on nimonic 80A alloy(National Institute of Science Communication and Information Resources (NISCAIR) ijact.editor@gmail.com Dr. K. S. Krishnan Marg (Near Pusa Gate) New Delhi 110-012, 2018) Sudhakar, S.; Kumar, P.; Srinivas, G.; Ravishankar, S.; Dupadu, D.; Barshilia, H.C.Micromachining techniques such as mechanical micro-drilling, electrical discharge machining (EDM) and laser beam machining (LBM) play an important role in the manufacturing of micro-devices used in mechanical, electronics, aerospace and medical applications. In this paper, an effort has been made to compare the performance of these micromachining techniques with regard to tool wear, burr formation and surface integrity. This is done by producing 20 micro-holes of approximately 800 ?m diameter on a rectangular block (90×30×3 mm3) of Nimonic 80A superalloy. TiAlN coated WC micro-drills, Cu electrodes and CO2 laser beam are used to produce these holes in conventional micro-drilling, EDM and LBM, respectively. The quality of the drilled hole (diameter, surface roughness and micro-burr formation), tool diameter analysis, taper angle and material removal rate (MRR) are compared and reported. A comprehensive analysis is also carried out on overcut, which leads to hole inaccuracy. Results show that mechanical micro-drilling produces better results in the above mentioned characteristics in comparison to LBM and EDM techniques. The relatively better performance of mechanical micro-drilling is attributed to the usage of TiAlN coating on WC tool. © 2018, National Institute of Science Communication and Information Resources (NISCAIR). All rights reserved.Item Highly fluorescent materials derived from ortho-vanillin: Structural, photophysical electrochemical and theoretical studies(Elsevier B.V., 2019) Poojary, S.; Acharya, M.; Abdul Salam, A.A.; Kekuda, D.; Nayek, U.; Madan Kumar, S.; Vasudeva Adhikari, A.V.; Dhanya, D.Small-molecule organic fluorophores are highly in demand attributed to their extensive prospective in material and biomedical applications. Particularly, luminescent ?-conjugated organic molecules that possess an efficient solid-state emission are excellent candidates for optoelectronic devices. Focusing on high demand of organic fluorophores, we herein report the synthesis of three organic fluorescent materials derived from o?vanillin, viz. an ester (F1), an azine (F2) and an azo dye (F3). Interestingly, F2 exhibited very intense luminescence in its aggregate phase due to the restriction in intra-molecular rotation (RIR), as demonstrated by solution thickening studies. Further, its Single Crystal X-ray Crystallography (SCXRD) study suggested the existence of various intra and inter molecular interactions and gave evidences for locked intra-molecular rotations of the benzene rings in the rigid conformation of the molecule. The bathochromic shift in fluorescence from solution to solid phase was confirmed by its thin-film emission spectrum, which evidences the formation of J-aggregates. The observed RIR, development of J-aggregates and high conjugation in F2 impart an excellent fluorescence in its aggregated state. Thin films of both F2 and F3 on ITO plates exhibited a bathochromic shift with a deep orange to red photoluminescence on UV excitation. Furthermore, the morphological characterization revealed the presence of clear dense grains in case of F2 and F3, while the DSC analysis indicated phase transitions of all the derivatives. As seen from dielectric measurement studies, the azo dye F3 exhibited the highest dielectric constant among the three derivatives. The electronic and photophysical data based on Density Functional Theory (DFT) and Time Dependent-DFT (TD-DFT) calculations are in agreement with the experimental results. All the above data clearly advocate that, the synthesized fluorophoric o?vanillin derivatives are excellent candidates for electro-optical devices. © 2018 Elsevier B.V.