Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Subject: search.filters.subject.Diffusible hydrogen

Search Results

Now showing 1 - 3 of 3
  • No Thumbnail Available
    Item
    Study on hydrogen assisted cracking susceptibility of HSLA steel by implant test
    (China Ordnance Society, 2016) Chakraborty, G.; Rejeesh, R.; Albert, S.K.
    DMR-249A is an indigenously developed high strength low alloy steel for Indian ship building industry for making ship-hull and is extensively used in the construction of war ships and submarines. Welding electrodes conforming to SFA 5.5 AWS E8018 C1 has been indigenously developed for welding of this steel using shielded metal arc welding process. In the present study, susceptibility to hydrogen assisted cracking of DMR-249A steel welds made using this electrode has been assessed using implant test. Implant tests were conducted using this electrode at two different levels of diffusible hydrogen, measured using gas chromatography technique. It is observed that both the steel and the welding consumable are not susceptible to hydrogen assisted cracking even with a high diffusible hydrogen level of 9 mL/100g of weld metal. In implant tests, specimen did not fracture even after loading to stress levels higher than the yield strength of the base metal. The good resistance of this steel and the welding consumable, even with high levels of diffusible hydrogen, is attributed to absence of a susceptible microstructure in both the weld metal and heat affected zone. Hence, this study shows that, in the absence of a susceptible microstructure, hydrogen assisted cracking is unlikely to occur even if hydrogen level is high. It also confirms that in welding of DMR-249A with indigenously developed E8018 C1 electrode, hydrogen assisted cracking is not a concern and no preheating is required to avoid it during welding. © 2016 The Authors
  • No Thumbnail Available
    Item
    Evaluation of hydrogen-assisted cracking susceptibility in modified 9cr-1mo steel welds
    (Springer, 2020) Chakraborty, G.; Rejeesh, R.; Ramana, O.V.; Albert, S.K.
    The hydrogen-assisted cracking susceptibility of modified 9Cr-1Mo steel weld is evaluated by Y-groove and gapped bead-on-plate test. It is found that a combination of pre + post heat is able to prevent cracking. However, the pre + post heat temperature combination determined from G-BOP test to prevent cracking (200 °C) is found to be higher than that in Y-groove test (100 °C). This is attributed to the higher weld restraint experienced in G-BOP than Y-groove test. For both the tests, the weld metal is found to be more susceptible to cracking than the heat affected zone. In addition to the diffusible hydrogen content of the welding consumables, diffusible hydrogen present in the G-BOP specimens prepared with different preheating and combinations of pre + post heat is also estimated by maintaining identical cooling conditions. The diffusible hydrogen in the weld for which no cracking is reported for G-BOP test (200 °C pre + post heat) is less than 1 ml/100 g. Considering the high restraint conditions present in the G-BOP test, it can be concluded that to prevent HAC in P91 steel, the choice of welding parameters (hydrogen content in welding consumable, heat input, pre/post-heating) should be such that diffusible hydrogen in the weld is brought down to below 1 ml/100 g. © 2019, International Institute of Welding.
  • No Thumbnail Available
    Item
    Effect of preheating and post heating in reducing diffusible hydrogen content and hydrogen assisted cracking susceptibility of modified 9Cr–1Mo steel
    (Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2020) Chakraborty, G.; Rejeesh, R.; Zubairuddin, M.; Albert, S.K.
    The hydrogen assisted cracking susceptibility of Modified 9Cr–1Mo steel weld is evaluated by implant test by determining lower critical stress for different preheating and combination of pre, post heating conditions. The diffusible hydrogen present in the implant specimens for different test conditions is estimated. Residual stress distribution in the weld for different heating condition is estimated using SYSWELD software. For a combination of pre + post heating at 200°C, the diffusible hydrogen content of the weld comes down to 1.17 from 4.7 mL/100g and the lower critical stress of the implant specimen increases from 250 to 370 MPa. Preheating + post heating also brings down the peak tensile residual stress level in the weld joints and lowers the cracking susceptibility. © 2020 Institute of Materials, Minerals and Mining. Published by Taylor & Francis on behalf of the Institute.