Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
36 results
Search Results
Item Inhibition of corrosion of mild steel in acid media by N'-benzylidene-3- (quinolin-4-ylthio)propanohydrazide(2008) Ramesh Saliyan, V.; Vasudeva Adhikari, A.V.In the present investigation a new corrosion inhibitor, N'-(3,4-dihydroxybenzylidene)-3-{[8-(trifluoromethyl)quinolin-4-yl]thio} propanohydrazide(DHBTPH) was synthesized, characterized and tested as a corrosion inhibitor for mild steel in HCl (1 M, 2 M) and H2SO 4 (0.5 M, 1 M) solutions using weight-loss method, electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization methods. The corrosion inhibition efficiency measured by all the above three techniques were in good agreement with each other. The results showed that DHBTPH is a very good inhibitor for mild steel in acidic media. The inhibition efficiency in different acid media was found to be in the decreasing order 0.5 M H 2SO4 > 1 M HCl > 1M H2SO4 > 2 M HCL The inhibition efficiency increases with increasing inhibitor concentration and with increasing temperature. It acts as an anodic inhibitor. Thermodynamic and activation parameters are discussed. Adsorption of DHBTPH was found to follow the Langmuir's adsorption isotherm. Chemisorption mechanism is proposed. The mild steel samples were also analysed by scanning electron microscopy (SEM). © Indian Academy of Sciences.Item Production of layer by layer Zn-Fe compositional multilayer alloy coatings using triangular current pulses for better corrosion protection(Maney Publishing, 2015) Bhat, R.S.; Hegde, A.Multiple-layer coatings of Zn-Fe alloy having alternatively the same compositions have been developed galvanostatically on mild steel (MS) from a single plating bath using triangular current pulses. Thiamine hydrochloride (THC) and citric acid (CA) were used as additives. Multiple-layer coatings were developed under different conditions of cyclic cathode current density (CCCD) and number of layers. Cyclic voltammetry demonstrated that the addition of THC and CA improves the deposit character by increasing the Ni content (through suppressing the deposition of Zn) via preferential adsorption on the cathode surface. The corrosion behaviours of the coatings were evaluated by electrochemical AC and DC methods. The optimum multiple-layer coating, represented as (Zn-Fe)3.0/5.0/300, was found to exhibit about four to five times better corrosion resistance when compared with monolayer (Zn-Fe)3.0 alloy, developed from the same bath for the same duration. Distinct phase structures responsible for interface formation between successive layers (which changes alternatively) were confirmed by X-ray diffraction analysis. Better corrosion resistance afforded by multiple-layer coating was attributed to the increased specific surface area of the coating because of layering. A synergistic effect of both structural difference between layers and individual layer thickness is responsible for enhanced corrosion resistance of the multiple-layer coatings. The formation of multiple layers and corrosion mechanism were analysed by scanning electron microscopy. © 2015 Institute of Materials Finishing.Item Development of multilayer Sn-Ni alloy coating by pulsed sonoelectrolysis for enhanced corrosion protection(Royal Society of Chemistry, 2016) Shetty, S.; Mohamed, M.J.; Bhat, D.; Hegde, A.C.Multilayer Sn-Ni alloy coating has been developed electrochemically on mild steel using an ultrasound effect, as a tool to modulate mass transfer process at electrical double layer, during deposition. Sn-Ni coatings having alternate layers of alloys of different compositions were developed on a nano/micrometric scale by pulsing sonicator ON (tON) and OFF (tOFF), periodically. The composition modulated multilayer alloy (CMMA) Sn-Ni coatings have been deposited by inducing the ultrasound field periodically at optimal current density. Corrosion performances of ultrasound-assisted multilayer Sn-Ni alloy coatings have been evaluated by electrochemical methods. Corrosion data revealed that CMMA Sn-Ni coating, developed using pulsed ultrasonic field and having 150 layers, represented as (Sn-Ni)2/2/150, is the most corrosion resistant, compared to its monolayer alloy coatings developed by both with/without ultrasound effect. Corrosion protection efficacy of multilayer coatings was found to be decreased at high degree of layering due to diffusion of layers. Improved corrosion resistance of multilayer Sn-Ni coatings is attributed to an increase in the number of layers, or interfaces separating alloys of the same metals, but of different composition, surface morphologies and phase structures, supported by energy dispersive spectroscopy, field emission scanning electron microscopy and X-ray diffraction study, respectively. The better corrosion protection of CMMA Sn-Ni coatings, compared to monolayer counterparts, is attributed to an increase in the number of layers, hence phase boundaries between layers, and experimental results are discussed. © 2018 The Royal Society of Chemistry.Item Ultrasound induced multilayer Ni-Co alloy coatings for better corrosion protection(Elsevier B.V., 2017) Shetty, A.R.; Hegde, A.Ultrasound induced multilayer Ni-Co alloy coatings have been developed galvanostatically by periodic modulation of ultrasound effect, parallel to the process of conventional electroplating. Multilayer Ni-Co alloy having alternative layers of different composition were developed by turning the sonicator probe, ON and OFF periodically, while keeping the current density (c.d.) constant. The deposition conditions, in terms of pulsing power density (p.d.) and degree of layering have been optimized for the highest performance of coating against corrosion, evaluated by electrochemical testing methods. Corrosion data revealed that under optimal conditions, multilayer Ni-Co alloy coating having 150 layers, represented as (Ni-Co)2/2/150 is about 11 times more corrosion resistant than its homogeneous coating, represented as (Ni-Co)4.0 A dm ? 2, deposited from the same bath for same duration of time. Improved corrosion resistance of multilayer Ni-Co alloy coatings was attributed to an increase in the number of interfaces, separating the layers of alloys of different composition, affected due to periodic pulsing of the sonicator. The dependence of corrosion behaviors at different combination of c.d. and p.d., on surface morphology, composition and phase structures were analyzed, using scanning electron microscopy (SEM), energy dispersion spectroscopy (EDS) and X-ray diffraction (XRD) technique, respectively. Experimental results are compared, and discussed. © 2017 Elsevier B.V.Item Effect of heat treatment on microstructure, corrosion, and shape memory characteristics of laser deposited NiTi alloy(Elsevier Ltd, 2018) Marattukalam, J.J.; Balla, V.K.; Das, M.; Bontha, S.; Kalpathy, S.K.The aim of this work is to study the effect of heat treatment on the microstructure, phase transformations, shape memory characteristics and corrosion behaviour of laser deposited equiatomic NiTi alloy. Dense samples of NiTi alloy were fabricated using Laser Engineered Net Shaping (LENS™) with two different laser energy densities by varying the scan speed and laser power. These samples were annealed for 30 min at 500 °C and 1000 °C in flowing argon, followed by furnace-cooling to room temperature. The resulting microstructures and properties were compared with the corresponding as-deposited samples. Microstructural analysis after heat treatment showed needle-shape martensite in the samples processed at lower laser energy density of 20 J/mm2, and lenticular or plate-like martensite in the samples processed at 80 J/mm2. The XRD results revealed relatively high concentration of martensite (B19?) in heat-treated NiTi alloy compared to as-processed samples. Furthermore, the heat treatment decreased the forward and reverse transformation temperatures of NiTi alloy from 80 – 95 °C to 20–40 °C, presumably due to annihilation of thermally induced defects. Interestingly, the samples annealed at 500 °C showed a measurable increase of 1–2% in the shape memory recovery, from the net recovery of 8% exhibited by the as-processed NiTi alloy. The corrosion resistance of laser-processed NiTi alloy decreased upon annealing. © 2018 Elsevier B.V.Item The impact of homogenization treatment on microstructure microhardness and corrosion behavior of wrought AZ80 magnesium alloys in 3.5 wt% NaCl solution(Institute of Physics Publishing helen.craven@iop.org, 2018) Naik, G.M.; Gote, G.D.; Narendranath, S.; Satheesh Kumar, S.S.This paper investigates the effect of homogenization treatment on microstructure, micro-hardness and corrosion behavior of AZ80 wrought Magnesium alloy. Homogenization at 523 K, 623 K, and 723 K were accomplished. Meanwhile samples were cooled in the furnace after 6 h and 12 h of diffusion annealing treatment. In this study, samples were characterized by using optical microscopy (OM) and scanning electron microscopy (SEM). Micro-hardness of the homogenized specimens were measured and electrochemical corrosion behavior of homogenized AZ80 alloy has been investigated. Attempt has been made to enhance both the hardness and corrosion resistance of the AZ80 Mg alloy by changing its microstructure during homogenization treatment. This investigation revealed that the hardness of Mg alloy is improved at 523 K-12 h holding time. It was also found that corrosion rates are minimum at higher homogenization temperature and lower holding time because of uniform distribution of secondary ?-phases in Mg matrix, evidently shown in the microstructure of the heat treated Mg alloy. As a result, the homogenization treatment at 723 K for 6 h is desirable to enhance the corrosion resistance. © 2018 IOP Publishing Ltd.Item Cyclic Oxidation and Hot Corrosion Behavior of Plasma-Sprayed CoCrAlY + WC-Co Coating on Turbine Alloys(Springer New York LLC barbara.b.bertram@gsk.com, 2018) Nithin, H.S.; Vijay, D.; Ramesh, M.R.Components in energy-producing systems suffer a variety of degradation processes such as oxidation and molten salt-induced corrosion as a consequence of complex multi-component gaseous environment. Coatings provide a composition that will grow the protective scale at high temperatures having long-term stability. Plasma spraying was used to deposit CoCrAlY + WC-Co composite coatings on turbine alloys of Hastelloy X and AISI 321. The thermocyclic oxidation behavior of coated alloys was investigated in static air and in molten salt (Na2SO4-60%V2O5) environment at 700 °C. The thermogravimetric technique was used to approximate the kinetics of oxidation in 50 cycles, each cycle consisting of heating and cooling. X-ray diffraction and SEM/EDAX techniques are used to characterize the oxide scale formed. Coated alloys showed a lower corrosion rate as compared to uncoated alloys. The coatings subjected to oxidation and hot corrosion showed slow scale growth kinetics. Preferential oxidation of Co, Cr, W and its spinel blocks the transport of oxygen and corrosive species into the coating by providing a barrier, thereby making the oxidation rate to reach steady state. As compared to the substrate alloys, coatings show better hot corrosion resistance. © 2018, ASM International.Item Effect of zinc and rare-earth element addition on mechanical, corrosion, and biological properties of magnesium(Cambridge University Press, 2018) Kottuparambil, R.R.; Bontha, S.; Ramesh, M.R.; Arya, S.; Jana, A.; Das, M.; Balla, V.K.; Amrithalingam, S.; Prabhu, T.R.The present work aims to understand the effect of zinc and rare-earth element addition (i.e., 2 wt% Gd, 2 wt% Dy, and 2 wt% of Gd and Nd individually) on the microstructure evolution, mechanical properties, in vitro corrosion behavior, and cytotoxicity of Mg for biomedical application. The microstructure results indicate that the Mg-Zn-Gd alloy consists of the lamellar long period stacking ordered phase. The electrochemical and immersion corrosion behavior were studied in Hanks balanced salt solution. Enhanced corrosion resistance with reduced hydrogen evolution volume and magnesium (Mg2+) ion release were estimated for the Mg-Zn-Gd alloy as compared to the other two alloy systems. At the early stage of corrosion, formation of the oxide film inhibited the corrosion propagation. However, at the later stages, the breaking of the oxide film leads to shallow pitting mode of corrosion. The ultimate tensile strength of Mg-Zn-Gd-Nd is better than the other two alloys due to the uniform distribution of the Mg12Nd precipitate phase. The moderate strength in the Mg-Zn-Gd alloy is due to the low volume fraction of the secondary phase. The MTT (methylthiazoldiphenyl-tetrazolium bromide) assay study was carried out to understand the cell cytotoxicity on the alloy surfaces. Studies revealed that all three alloys had significant cellular adherence and no adverse effect on cells. © 2018 Materials Research Society.Item On the corrosion resistance of some selective laser melted alloys(Elsevier B.V., 2018) Suryawanshi, J.; Baskaran, T.; Prakash, O.; Arya, S.; Ramamurty, U.The electrochemical corrosion resistances of selective laser melted (SLM) 316 L austenitic stainless steel (SS), 18(Ni) 300-grade maraging steel (MS), and Al-12 wt.% Si (AS) alloy in a 0.1 M NaCl solution at room temperature were evaluated. The effects of laser scanning strategy (single melt vs. checker board styles), post-SLM heat treatment, and corroding surface orientation (with respect to the scan and build directions) on the corrosion behavior were examined. In all cases, results were compared with those obtained on samples with the same compositions, but manufactured using conventional means. The experimental results show that, for the particular set of experimental conditions employed in this study, SLM in general improves the corrosion resistances of Al-12 wt.% Si and stainless steel alloys and degrades the corrosion resistance of the maraging steel, in comparison to the respective corrosion resistances of their conventionally manufactured counterparts. These results are discussed in terms of microstructural refinement and porosity that are common to the SLM alloys. © 2018 Acta Materialia Inc.Item Effects of combined multiaxial forging and rolling process on microstructure, mechanical properties and corrosion behavior of a Cu-Ti alloys(Institute of Physics Publishing helen.craven@iop.org, 2019) Ramesh, S.; Anne, G.; Shivananda Nayaka, H.; Sahu, S.; Arya, S.Combined multiaxial forging (MAF) and rolling was performed on Cu-3% Ti (wt%) alloy at room temperature with emphasis on microstructural evolution, improvement in mechanical properties, and corrosion resistance. Microstructural changes were confirmed from various characterization techniques, and co-related with mechanical properties. TEM analysis revealed high shear band density in the 3 pass MAF + 90% rolled sample appearing due to high strain. EBSD analysis revealed transformation to low angle grain boundaries from high angle grain boundaries. Maximum microhardness and UTS reached to 340 HV and 960 MPa, respectively in the processed samples. Significant grain refinement was observed in MAF processed Cu-3%Ti alloy, and after combined MAF + rolling, higher dislocation density and refinement of shear bands were observed. In addition, potentio-dynamic polarization test was used to study the corrosion behavior of the alloy. Scanning electron microscope (SEM) was used to analyze the corroded surface morphology. © 2019 IOP Publishing Ltd.