Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
47 results
Search Results
Item Flow visualization and study of critical heat flux enhancement in pool boiling with Al2O3-water nanofluids(Serbian Society of Heat Transfer Engineers, 2012) Hegde, R.N.; Rao, S.S.; Reddy, R.P.Pool boiling heat transfer characteristics of Al2O3 -water nanofluids is studied experimentally using a NiCr test wire of 36 standard wire guage diameter. The experimental work mainly concentrated on (1) change of critical heat flux with different volume concentrations of nanofluid and (2) flow visualization of pool boiling using a fixed concentration of nanofluid at different heat flux values. The experimental work revealed an increase in critical heat flux value of around 48% andflow visualization helped in studying the pool boiling behaviour of nanofluid.Out of the various reasons which could affect the critical heatflux enhancement, surface roughness plays a major role in pool boiling heat transfer.Item Flow visualization, critical heat flux enhancement, and transient characteristics in pool boiling using nanofluids(ASTM International, 2012) Hegde, R.N.; Rao, S.S.; Reddy, R.P.This paper presents the experimental outcome of a study of the pool boiling heat transfer characteristics of alumina and CuO nanofluid in distilled water using a 0.19 mm diameter NiCr wire. A series of experiments were conducted in order to visualize the flow, critical heat flux (CHF) enhancement, and transient characteristics of nanofluid. The boiling phenomenon was visualized using a 0.1 g/l concentration of alumina nanofluid. The average bubble diameter was measured and was found to increase with increased heat flux. The average bubble contact angle decreased from 69° during the initial stages of boiling to 33° at CHF. Massive vapour bubbles were observed on the test heater surface near the CHF, inducing vapour blankets and forming hot/dry spots. The increase in the CHF could be well explained by the hot/dry spot theory. Pool boiling experiments conducted using low volume concentrations of CuO-water nanofluid at atmospheric pressure in distilled water showed an increase in the CHF by 30 % at a 0.3 g/l concentration. The transient behaviour of nanofluid, examined by exposing the heater surface at a constant heat flux of 700 kW/m2, indicated CHF enhancement of 5.21 % to 6.77 % for the two time durations. Based on the experimental investigations, it was concluded that the CHF enhancement is due to nanoparticle coating, which changes the thickness of the surface as a function of time and surface wettability and corroborates the hot/dry spot theory. Copyright © 2012 by ASTM International.Item Additive manufacturing of an aluminum matrix composite reinforced with nanocrystalline high-entropy alloy particles(Elsevier Ltd, 2017) Karthik, G.M.; Panikar, S.; Janaki Ram, G.D.J.; Kottada, R.S.In the present work, a metal-metal composite consisting of aluminum-magnesium alloy AA5083 matrix and nanocrystalline CoCrFeNi high-entropy alloy reinforcement particles in 12 vol% was successfully friction deposited in multiple layers. The layer interfaces or the reinforcement/matrix interfaces showed no brittle intermetallic formation – thanks to the inert nature as well as the high strength and hardness of the high-entropy alloy reinforcement particles. The composite showed significantly higher tensile and compressive strengths as compared to standard wrought-processed alloy AA5083-H112 and offered a much better combination of strength and ductility when compared to conventional aluminum matrix composites reinforced with ceramic particles. The current study establishes friction deposition as a viable technique for additive manufacturing of novel high-performance composite materials. © 2016 Elsevier B.V.Item Role of thermally grown oxide and oxidation resistance of samarium strontium aluminate based air plasma sprayed ceramic thermal barrier coatings(Elsevier B.V., 2017) Baskaran, T.; Arya, S.B.Samarium Strontium Aluminate (SSA) based ceramic oxide was synthesized and coated on a bond coated (NiCrAlY) Inconel 718 superalloy by air plasma spray (APS) process. Thermally grown oxide (TGO) thicknesses were controlled at different pre-oxidation times of 10, 20 and 30 h at 1050 °C in the argon atmosphere, the highest TGO thickness being found for 30 h pre-oxidized samples. The percentage elastic recovery of pre-oxidized samples increased (45, 48, and 50%) with an increasing pre-oxidation time at 1050 °C. The isothermal oxidation test was performed on pre-oxidized samples at 1100 °C for 15 h in air. The parabolic oxidation rate constant decreased from 6.08 × 10? 5 to 3.90 × 10? 5 mg2 cm? 4 s? 1 (from 10 to 20 h) and then increased up to 4.55 × 10? 5 mg2 cm? 4 s? 1 for 30 h pre-oxidized SSA samples at 1100 °C. SSA based TBCs showed 65% lower weight gain as compared to conventional YSZ TBCs after oxidation at 1100 °C in air. Cross-sectional SEM results revealed that the threshold TGO thickness of SSA TBCs is about 5.3 to 5.8 ?m. Failure of SSA TBCs was observed at the interface of TGO and ceramic top coat due to the formation of SmAlO3 along with spinel oxides. © 2017Item Formation of microstructural features in hot-dip aluminized AISI 321 stainless steel(University of Science and Technology Beijing, 2018) Huilgol, P.; Rajendra Udupa, K.; Udaya Bhat, K.Hot-dip aluminizing (HDA) is a proven surface coating technique for improving the oxidation and corrosion resistance of ferrous substrates. Although extensive studies on the HDA of plain carbon steels have been reported, studies on the HDA of stainless steels are limited. Because of the technological importance of stainless steels in high-temperature applications, studies of their microstructural development during HDA are needed. In the present investigation, the HDA of AISI 321 stainless steel was carried out in a pure Al bath. The microstructural features of the coating were studied using scanning electron microscopy and transmission electron microscopy. These studies revealed that the coating consists of two regions: an Al top coat and an aluminide layer at the interface between the steel and Al. The Al top coat was found to consist of intermetallic phases such as Al7Cr and Al3Fe dispersed in an Al matrix. Twinning was observed in both the Al7Cr and the Al3Fe phases. Furthermore, the aluminide layer comprised a mixture of nanocrystalline Fe2Al5, Al7Cr, and Al. Details of the microstructural features are presented, and their formation mechanisms are discussed. © 2018, University of Science and Technology Beijing and Springer-Verlag GmbH Germany, part of Springer Nature.Item HVOF sprayed Ni3Ti and Ni3Ti+(Cr3C2+20NiCr) coatings: Microstructure, microhardness and oxidation behaviour(Elsevier Ltd, 2018) Reddy, N.C.; Kumar, B.S.A.; Reddappa, H.N.; Ramesh, M.R.; Koppad, P.G.; Kord, S.This paper reports the development of Ni3Ti and Ni3Ti+(Cr3C2+20NiCr) coatings on AISI 420 stainless steel (MDN-420) and titanium alloy ASTM B265 (Ti-15) by HVOF technique. Microstructure, microhardness and high temperature oxidation behaviour of coatings were investigated. Microstructure of coatings was dense and displayed layers depicting lamellar structure. The microhardness of coatings was significantly higher than that of substrate owing to higher density and cohesive strength between individual splats of coating materials. Cyclic oxidation studies conducted on Ni3Ti and Ni3Ti+(Cr3C2+20NiCr) coatings showed oxide scale was composed of various oxides like NiO, NiCr2O4 and Cr2O3 phases. The formation of compact and protective NiO phase in case of Ni3Ti coatings; NiO and Cr2O3 phases in Ni3Ti+(Cr3C2+20NiCr) coatings stabilised the weight gain exhibited slow oxidation rate at higher temperatures. © 2017 Elsevier B.V.Item Microstructure and Adhesion Strength of Ni3Ti Coating Prepared by Mechanical Alloying and HVOF(Pleiades Publishing compmg@maik.ru, 2018) Reddy, N.C.; Ajay Kumar, B.S.; Ramesh, M.R.; Koppad, P.G.In the present work we report the development of Ni3Ti intermetallic compound by high energy ball milling of Ni and Ti powders. The ball milled powders were taken at various intervals (4, 6, 8, 10, and 11 h) to analyze the formation of NixTix intermetallic compounds. The ball milled powders were analyzed using scanning electron microscopy and X-ray diffraction. The layered shaped powder particles of Ni3Ti phase were formed after 11 h of ball milling, which was confirmed by X-ray peaks. Further High-Velocity Oxy-Fuel (HVOF) process was used to coat Ni3Ti and Ni3Ti + (Cr3C2 + 20NiCr) on MDN 420 steel. Both the coated materials displayed excellent cohesion with minimal porosity less than 2%. The tensile adhesion strength test was carried out on these coatings to check the bond strength. Out of the two the Ni3Ti coating showed excellent bond strength of 41.04 MPa compared to that of Ni3Ti + (Cr3C2 + 20NiCr) coating. © 2018, Pleiades Publishing, Ltd.Item Elevated temperature solid particle erosion behaviour of carbide reinforced CoCrAlY composite coatings(Institute of Physics Publishing helen.craven@iop.org, 2018) Nithin, H.S.; Desai, V.; Ramesh, M.R.CoCrAlY+WC-Co and CoCrAlY+Cr3C2-NiCr coatings are deposited on nickel based alloy using atmospheric plasma spray technique. Mechanical properties such as microhardness, adhesion strength and fracture toughness of coatings are evaluated. Elevated temperature solid particle erosion behaviour of these coatings are investigated at 600 °C using alumina erodent at 30 and 90° impact angle. Coatings are characterized utilizing Scanning electron microscope (SEM), x-ray diffraction (XRD) and Energy dispersive spectroscopy (EDS). CoCrAlY+WC-Co coating shows higher hardness, adhesion strength and fracture toughness than CoCrAlY+Cr3C2-NiCr coating. CoCrAlY+WC-Co coating exhibited approximately 3 times higher erosion resistance than CoCrAlY+Cr3C2-NiCr coating at 90° and 30° impact angles. SEM images of eroded surfaces of coatings reveals the combination of ductile and brittle fracture. CoCrAlY+Cr3C2-NiCr coating shows severe cracks, craters, carbide pull out and chipping than CoCrAlY+WC-Co coating. High temperature erosion is a combination of simultaneous building up of material by oxidation and removal of material by erosion process. Thus reforming the erosion process to oxidation modified erosion process. © 2018 IOP Publishing Ltd.Item Influence of microwave hybrid heating on the sliding wear behaviour of HVOF sprayed CoMoCrSi coating(Institute of Physics Publishing helen.craven@iop.org, 2018) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.CoMoCrSi superalloy powder (Tribaloy-T400) consists of intermetallic laves phase and primary eutectic phase of Co-rich solid solution. Processing of Tribaloy-T400 powder is carried out through high-energy ball milling (HEBM) technique to obtain a higher volume fraction of intermetallic laves phases. The feedstock is sprayed using high-velocity-oxy-fuel (HVOF) process on titanium grade-15 substrate. The coating microstructure is homogenized by microwave hybrid heating technique. Characterization of feedstock, as-sprayed and microwave fused coatings is done by using Scanning Electron Microscopy (SEM), Energy dispersive spectroscopy (EDS) and x-ray Diffraction (XRD). Porosity, surface roughness, microhardness, and bond strength are measured. Adhesive wear behavior of the coatings under the dry sliding condition is evaluated at an applied load of l0 and 20 N and temperature of 200, 400 and 600 °C Fused coating exhibit higher wear resistance than the as-sprayed coatings and substrate. The hard intermetallic laves phases which are amorphous (bulk metallic glass) in nature strengthen the coating at high temperatures. © 2018 IOP Publishing Ltd.Item Cyclic Oxidation and Hot Corrosion Behavior of Plasma-Sprayed CoCrAlY + WC-Co Coating on Turbine Alloys(Springer New York LLC barbara.b.bertram@gsk.com, 2018) Nithin, H.S.; Vijay, D.; Ramesh, M.R.Components in energy-producing systems suffer a variety of degradation processes such as oxidation and molten salt-induced corrosion as a consequence of complex multi-component gaseous environment. Coatings provide a composition that will grow the protective scale at high temperatures having long-term stability. Plasma spraying was used to deposit CoCrAlY + WC-Co composite coatings on turbine alloys of Hastelloy X and AISI 321. The thermocyclic oxidation behavior of coated alloys was investigated in static air and in molten salt (Na2SO4-60%V2O5) environment at 700 °C. The thermogravimetric technique was used to approximate the kinetics of oxidation in 50 cycles, each cycle consisting of heating and cooling. X-ray diffraction and SEM/EDAX techniques are used to characterize the oxide scale formed. Coated alloys showed a lower corrosion rate as compared to uncoated alloys. The coatings subjected to oxidation and hot corrosion showed slow scale growth kinetics. Preferential oxidation of Co, Cr, W and its spinel blocks the transport of oxygen and corrosive species into the coating by providing a barrier, thereby making the oxidation rate to reach steady state. As compared to the substrate alloys, coatings show better hot corrosion resistance. © 2018, ASM International.