Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
11 results
Search Results
Item Multi objective optimisation of thermally enhanced machining parameters of Inconel 718 using grey relational analysis(Inderscience Publishers, 2017) Ganta, V.; Kalichetty, K.S.; Dupadu, D.The present work investigates an experimental study of thermally enhanced machining of nickel-based superalloy Inconel 718 using uncoated tungsten carbide inserts. An inexpensive flame heating technique using an oxyacetylene flame is used as a heat source for thermal enhancement of workpiece. The effects of cutting parameters like cutting speed, feed rate, depth of cut and temperature of workpiece on the performance characteristics like surface roughness, tool wear and material removal rate were studied. A L27 orthogonal array with four parameters and three levels was adopted for experimental design. Multi response optimisation was done using grey relation analysis to simultaneously minimise surface roughness, tool wear and to maximise material removal rate. It was observed that at cutting speed at 85.21 m/min, feed rate at 0.048 m/min, depth of cut at 0.6 mm and workpiece temperature at 600°C were optimal cutting parameters. It is clearly shown that the above performance characteristics in thermally enhanced machining can be improved effectively through this approach. © © 2017 Inderscience Enterprises Ltd.Item Comparative evaluations of machining performance during turning of 17-4 PH stainless steel under cryogenic and wet machining conditions(Taylor and Francis Inc. 325 Chestnut St, Suite 800 Philadelphia PA 19106, 2018) Sivaiah, P.; Dupadu, D.Productivity in machining of 17-4 PH stainless steel is adversely affected by the premature failure of tool and poor surface finish as a consequence of high cutting temperatures. Conventional cutting fluids not only create environmental and health problems but also fail to overcome the high cutting temperatures during machining. Cryogenic cooling is an environmentally clean cooling technology for attractive management of machining zone temperatures. The present study investigates the effect of cryogenic liquid nitrogen (LN2 at ?196°C) on cutting temperatures, cutting forces (main cutting force, feed force), surface roughness, tool flank wear and chip morphology in turning of 17-4 PH stainless steel with AlTiN PVD-coated tungsten-coated carbide inserts and results were compared to wet machining. In overall, cryogenic machining reduces the cutting temperature, cutting forces, surface roughness and tool flank wear to a maximum of 73.4, 17.62, 44.29 and 55.55%, respectively. Improved chip breakability was found in cryogenic machining. © 2018 Taylor & Francis Group, LLC.Item Investigation of machinability characteristics on EN47 steel for cutting force and tool wear using optimization technique(Institute of Physics Publishing helen.craven@iop.org, 2018) Mallesha, M.; Shivananda Nayaka, H.In this experimental work dry turning process carried out on EN47 spring steel with coated tungsten carbide tool insert with 0.8 mm nose radius are optimized by using statistical technique. Experiments were conducted at three different cutting speeds (625, 796 and 1250 rpm) with three different feed rates (0.046, 0.062 and 0.093 mm/rev) and depth of cuts (0.2, 0.3 and 0.4 mm). Experiments are conducted based on full factorial design (FFD) 33 three factors and three levels. Analysis of variance is used to identify significant factor for each output response. The result reveals that feed rate is the most significant factor influencing on cutting force followed by depth of cut and cutting speed having less significance. Optimum machining condition for cutting force obtained from the statistical technique. Tool wear measurements are performed with optimum condition of Vc = 796 rpm, ap = 0.2 mm, f = 0.046 mm/rev. The minimum tool wear observed as 0.086 mm with 5 min machining. Analysis of tool wear was done by confocal microscope it was observed that tool wear increases with increasing cutting time. © 2018 IOP Publishing Ltd.Item Influence of materials and machining parameters on drilling performance of syntactic foams(ASTM International, 2018) Ashrith, H.S.; Doddamani, M.; Gaitonde, V.N.; Gupta, N.The effects of drilling parameters and material properties are investigated on epoxy matrix syntactic foams reinforced with 20, 40, and 60 volume percent glass microballoon. The influences of cutting speed, feed, drill diameter, and filler content on drilling performance are studied based on the full factorial design of experiments using tungsten carbide twist drills. Based on experimental results, machinability aspects within the range of the chosen input parameters are predicted using response surface methodology-based models, which can guide industrial practitioners for choosing the appropriate process parameters. Microscopy is conducted on the drilled specimens to understand crack initiation and propagation mechanisms. The thrust force and specific cutting coefficient of syntactic foam are 40 % lower as compared to those of neat epoxy. The surface roughness of syntactic foams is higher than that of neat epoxy. The micrographs of drill bits show negligible tool wear. These results show the possibility of using syntactic foams in industrial applications in which the drilling of material is required for reasons such as joining using bolts. © © 2018 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959Item Performance evaluation of mechanical micro-drilling, electrical discharge machining and laser beam machining on nimonic 80A alloy(National Institute of Science Communication and Information Resources (NISCAIR) ijact.editor@gmail.com Dr. K. S. Krishnan Marg (Near Pusa Gate) New Delhi 110-012, 2018) Sudhakar, S.; Kumar, P.; Srinivas, G.; Ravishankar, S.; Dupadu, D.; Barshilia, H.C.Micromachining techniques such as mechanical micro-drilling, electrical discharge machining (EDM) and laser beam machining (LBM) play an important role in the manufacturing of micro-devices used in mechanical, electronics, aerospace and medical applications. In this paper, an effort has been made to compare the performance of these micromachining techniques with regard to tool wear, burr formation and surface integrity. This is done by producing 20 micro-holes of approximately 800 ?m diameter on a rectangular block (90×30×3 mm3) of Nimonic 80A superalloy. TiAlN coated WC micro-drills, Cu electrodes and CO2 laser beam are used to produce these holes in conventional micro-drilling, EDM and LBM, respectively. The quality of the drilled hole (diameter, surface roughness and micro-burr formation), tool diameter analysis, taper angle and material removal rate (MRR) are compared and reported. A comprehensive analysis is also carried out on overcut, which leads to hole inaccuracy. Results show that mechanical micro-drilling produces better results in the above mentioned characteristics in comparison to LBM and EDM techniques. The relatively better performance of mechanical micro-drilling is attributed to the usage of TiAlN coating on WC tool. © 2018, National Institute of Science Communication and Information Resources (NISCAIR). All rights reserved.Item Influence of deep cryogenic treatment on performance of cemented carbide (WC-Co) inserts during dry end milling of maraging steel(Elsevier Ltd, 2019) Varghese, V.; Ramesh, M.R.; Dupadu, D.Cryogenic treatment has developed as a technique to improve the life of the cutting tool, especially tungsten carbide inserts. The present study investigates the effect of cryogenic treatment of cemented carbide (WC-Co) inserts at the different soaking period of 18 h (CT-18), 24 h (CT-24) and 32 h (CT-32) at a sub-zero temperature of ?196 °C. The soaking period plays a crucial role in improving the wear resistance of the cryogenically treated tools. It is vital to determine the critical soaking period for the cryogenic treatment of cemented carbides. The mechanical and metallurgical characterization of cryogenically treated cemented carbide insert is carried out to understand the changes in the microstructure, grain size, chemical composition, microhardness and electrical conductivity after cryogenic treatment. The end milling experiments on maraging steel under dry environment are carried out using cryogenically treated inserts at different holding time and untreated inserts (UT). The machining performance of treated and untreated inserts are compared with respect to tool wear, surface roughness and cutting forces. The results revealed that cryogenic treatment is effective in resisting tool wear even at high spindle speeds. The cryogenically treated inserts exhibited higher tool life, better surface finish and lower cutting forces during machining at different spindle speeds. The optimum soaking time for cryogenic treatment of WC-Co inserts is found to be 24 h (CT-24) beyond which there is no improvement in microhardness and wear resistance. © 2018Item Characterisation and performance evaluation of TiSiN &tiAlSiN coatings by RF magnetron sputtering deposition during end milling of maraging steel(Institute of Physics Publishing helen.craven@iop.org, 2019) Varghese, V.; Ramesh, M.R.; Dupadu, D.; Shaik, H.Monolayer nanostructured thin films of TiSiN & TiAlSiN were deposited on WC-Co milling inserts using RF magnetron sputtering for metal cutting. The alloy targets of TiSi (80/20 at%) & TiAlSi (34/56/10 at%) were used for the deposition in an Ar + N atmosphere. The deposition time and parameters are optimized to develop a uniform and homogenous coating. The mechanical and metallurgical properties are characterized to analyze the wear resistance of the coating. The machinability studies on MDN 250 maraging steel is carried out using TiSiN and TiAlSiN coated WC-Co inserts under dry and wet environment. The machining responses such as surface roughness, cutting force, tool wear and tool life are analyzed by varying spindle speed. The results showed that TiAlSiN coating had a higher wear resistance and machining performance compared to the TiSiN coating owing to the high hardness and plasticity index of the coating. © 2020 IOP Publishing Ltd.Item Investigation on the performance of AlCrN and AlTiN coated cemented carbide inserts during end milling of maraging steel under dry, wet and cryogenic environments(Elsevier Ltd, 2019) Varghese, V.; K, A.; Ramesh, M.R.; Dupadu, D.The present study investigates the machining performance of AlCrN and AlTiN coated cemented carbide inserts during end milling of MDN 250 maraging steel. The mechanical and metallurgical characterization is carried out to determine the properties of the PVD coatings developed. The end milling experiments under dry, wet and cryogenic environment is carried out using coated uncoated inserts (UC) at different spindle speeds to evaluate the machining performance in terms of tool life, surface roughness and cutting forces. The coated inserts showed higher tool life, better surface finish, and low cutting forces during machining at different spindle speeds. It is found that the AlCrN coating had a better wear resistance and machining performance in comparison with AlTiN coating. The cryogenic environment reduced the surface roughness & cutting force and improved the tool life of the cutting tool compared to conventional dry and wet environment. It is revealed that coated tools along with cryogenic cooling can be employed for high-speed machining applications. © 2019 The Society of Manufacturing EngineersItem Experimental investigation of cryogenic end milling on maraging steel using cryogenically treated tungsten carbide-cobalt inserts(Springer, 2019) Varghese, V.; Ramesh, M.R.; Dupadu, D.The cryogenic machining and cryogenic treatment have already emerged as the sustainable manufacturing process of the future generation. The cryogenic treatment improves the cutting tool life, but the high cutting temperature developed during high-speed machining reduces the effect of cryogenic treatment of cutting tool. This study investigates the possible improvements in cutting tool life by combining cryogenic cooling and cryogenic treatment. The authors believe that these two techniques can replace conventional machining approaches using dry and wet machining conditions using coated carbide tools. The tungsten carbide-cobalt inserts are cryogenically treated (CT) at a soaking temperature of ? 195.8 °C for a period of 24 h and are used to evaluate milling performance under dry, wet, and cryogenic cutting environments. The machining experiments are conducted on maraging steel MDN 250 using one factor at a time approach by varying spindle speed and keeping feed rate and depth of cut as constant. The cutting force, surface roughness, tool wear, and subsurface microhardness are some of the machining responses evaluated and compared with an untreated cutting tool (UT). The tool life improved up to 24% during cryogenic machining using CT tools at a spindle speed of 270 rpm. © 2019, Springer-Verlag London Ltd., part of Springer Nature.Item Advantages of cryogenic machining technique over without-coolant and with-coolant machining on SS316(IOP Publishing Ltd, 2021) Karthik, M.; Malghan, R.L.; Shettigar, A.K.; Herbert, M.A.; Rao, S.S.The analysis concentrated towards the influence of speed of the spindle along with a cryogenic (LN2) cooling technique in treating SS316 usingCNC(Computerized numerical control) milling machine. An comparative study path was set and anlyised among three states i.e. Dry (Without coolant), wet (With coolant) and cryogenic (With liquid LN2) machining using coated carbide inserts. The coolant used in case of wet machining was water-soluble, referred to as cutting fluid. The experimental range falls in 3 different levels of spindle speed (SS), such as low level (1000 rpm), medium level (2000 rpm), and high level (3000 rpm), respectively. Meanwhile, feed rate (FR) and depth of cut (DOC) were reserved steadily with 450 mm min-1, 1 mm separately. This vital focus is towards cryogenic (LN2) machining effects and its perception of machinability on SS316, such as tool wear -TW(?m), cutting force-CF (N), cutting temperature-CT (oC) and surface roughness-Ra (?m). The experiments were conducted and documented with cryogenic (LN2) techniques to establish the fairness and practicability of the method to compare with without-coolant (dry) and with-coolant (wet) machining. The attained statistical results in comparison of LN2 method over without-coolant and with-coolant machining concerned to test cases for CF- Fx (N), CT(oC), Ra (?m) andFW(?m) are 53.21%-34.20%, 65.88%-44.51%, 75.43%-44.27%,&59.76%-23.10%, respectively. © 2021 IOP Publishing Ltd.