Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
10 results
Search Results
Item Strength retention characteristics of concrete cubes subjected to elevated temperatures(2010) Yaragal, S.C.; Clarke, K.S.; Mahesh Babu, K.; Ashokumar, S.; Venkataramana, K.; Babu Narayan, K.S.; Chinnagiri Gowda, H.C.; Reddy, G.R.; Sharma, A.Concrete in structures is likely to be exposed to high temperatures during fire. The relative properties of concrete after such an exposure are of great importance in terms of the serviceability of buildings. The probability of its exposure to elevated temperatures is high due to natural hazards, accidents and sabotages. Therefore, the performance of concrete during and after exposure to elevated temperature is a subject of great interest to the designer. Physical changes like cracking, colour change, spalling and chemical changes like decomposition of Ca(OH)2 and the C-S-H gel take place when subjected to elevated temperatures. This work reports the characteristics of concrete at elevated temperatures. Popular normal strength grades (M20, M25, M30, M35, M40 and M45) produced by Ready Mix Concrete (RMC) India, Mangalore have been used in production of test specimens (150 mm cubes) to obtain more meaningful and realistic data. In the preliminary phase 150 mm cubes were cast, cured and tested by destructive method for gathering data on strength characteristics. Later these test samples were subjected to elevated temperatures ranging from 100°C to 800°C, in steps of 100°C with a retention period of 2 hours. After exposure, weight losses were determined and then again destructive tests were conducted to estimate the residual compressive strength. Test results indicated that weight and strength significantly reduces with an increase in temperature. © 2010 CAFET-INNOVA TECHNICAL SOCIETY.Item Effect of recuring on compressive strength of thermally deteriorated concrete cubes(2011) Prasanth, S.; Yaragal, S.C.; Babu Narayan, K.S.Concrete is found to undergo degradation when subjected to elevated temperatures during an event such as fire and lose substantial amount of its strength. The loss of strength in concrete is mainly attributed to decomposition of C-S-H and release of chemically bound water, which begins when the exposure temperature exceeds 500°C. When thermally deteriorated concrete is supplied with water there is a substantive gain in strength as a consequence of rehydration of cement that is initiated. This paper presents results of an experimental program carried out to investigate the effect of recuring on strength gain of normal strength concrete specimens subjected to elevated temperatures from 500°C to 800°C, which were subjected to retention time of two hours at the designated temperatures. © 2011 CAFET-INNOVA TECHNICAL SOCIETY. All rights reserved.Item Recuring studies on concretes subjected to elevated temperatures and suddenly cooled by water quenching(Multi-Science Publishing Co. Ltd, 2015) Yaragal, S.C.; Kittur, M.M.; Babu Narayan, K.S.Concrete is found to undergo degradation when subjected to elevated temperatures during an accidental event, such as fire and lose substantial amount of its original strength. The loss of strength in concrete is mainly attributed to the decomposition of Calcium Silicate Hydrate (C-S-H) and release of chemically bound water, which begins when the exposure temperature exceeds 500°C. When such a concrete is supplied with water and allowed to recure, it is found to recover substantial amount of its lost strength. This work is carried out to investigate the effect of recuring on strength recovery of un-blended and blended concrete specimen (100 mm cubes) subjected to elevated temperatures from 400°C to 700°C, in steps of 100°C, for a retention period of two hours at the designated temperatures. The concrete cubes immediately after exposure were subjected to thermal shock by quenching them in water, and then temperature of thermally shocked concrete is allowed to cool to room temperature. The cooled specimen were then recured in water for 1, 3, 7, 14, 21, 28, 56 days and tested for compressive strength recovery. These studies were carried out for Portland Cement (PC) based concrete and Portland & Granulated Blast Furnace Slag (70% PC + 30% GGBS) based concrete (blended concrete), and some interesting results are presented and discussed in this paper. © 2015, Multi-Science Publishing Co. Ltd. All rights reserved.Item Use of Stabilized Lateritic and Black Cotton Soils as a Base Course Replacing Conventional Granular Layer in Flexible Pavement(Springer, 2020) Amulya, S.; Ravi Shankar, A.U.The present work investigates the improved properties of lateritic and black cotton soils stabilized with ground granulated blast furnace slag (GGBFS) and alkali solutions. The alkali solution includes a mixture of sodium hydroxide and sodium silicate. The lateritic and black soils are treated with 30% GGBFS and the alkali solutions consisting of 6% Na2O having silica modulus (Ms) of 0.5, 1.0 and 1.5 at a constant water binder ratio of 0.25. The treated samples were air-cured for 0 (immediately after casting), 3, 7 and 28 days at ambient temperature. The treated lateritic soil with 0.5 and 1.0 Ms is found durable after 3, 7, and 28 days curing. Whereas, the treated BC soil found durable with Ms 0.5 at modified Proctor density after 28 days curing. The formation of calcium silicate hydrate and calcium aluminosilicate hydrate structures resulted in a remarkable improvement of compressive strength, flexure and fatigue life of treated soils due to dissolved calcium ions from GGBFS, silicate and aluminium ions from alkali solutions. The microstructure image of the durable soil sample shows the crystal orientation of particles. The design of high and low volume roads is proposed by replacing the conventional granular layer with the durable stabilized soil and stress–strain analysis is carried out using pavement analysis software. © 2020, Springer Nature Switzerland AG.Item Replacement of Conventional Base Course with Stabilized Lateritic Soil Using Ground Granulated Blast Furnace Slag and Alkali Solution in the Flexible Pavement Construction(Springer, 2020) Amulya, S.; Ravi Shankar, A.U.The use of cement/chemical-treated base and sub-bases is widely recommended in the pavement construction. Therefore, this paper investigates the behaviour of stabilized lateritic soil as a base course in flexible pavement by replacing the granular base course. The lateritic soil was stabilized with 25% Ground Granulated Blast Furnace Slag (GGBFS) along with the alkali solutions such as sodium hydroxide and sodium silicate at a varying sodium oxide (Na2O) contents of 4, 5 and 6%, silica modulus (Ms, a ratio of silica to sodium oxide) of 0.5, 1.0 and 1.5 and a constant water binder ratio (w/b) of 0.25. The maximum compressive strengths of 5452 and 6593 kPa were achieved for a treated sample consisting of 6% Na2O and 1.0 Ms cured for 28 days at the light and heavy compactions, respectively, which is due to the formation of calcium silicate hydrates when calcium oxide-rich GGBFS reacts with water. Further with the curing period results in an increase in strength due to the formation of calcium alumino-silicate hydrates when GGBFS reacts with alkali solutions. The durability of the samples was evaluated by wetting–drying and freezing–thawing tests. The samples passing the required durability criteria were tested for flexural strength and fatigue life. Scanning electron microscope images showed closely packed crystal orientation indicating high strength. Low and high volume pavements were designed using stabilized soil as a base course, and the strains were evaluated using pavement analysis software. It is suggested that the conventional granular base layer can be replaced with the stabilized soil. © 2020, Indian Geotechnical Society.Item Utilization of lateritic soil stabilized with alkali solution and ground granulated blast furnace slag as a base course in flexible pavement construction(Springer, 2020) Amulya, A.; Ravi Shankar, A.U.; Singh, A.; Pammar, K.H.The natural aggregates are depleting in developing countries due to the excessive usage in road and building construction. In the present study, the engineering properties of abundantly available lateritic soil stabilized with Ground Granulated Blast Furnace Slag (GGBS) and alkali solutions like Sodium hydroxide and Sodium silicate was evaluated. The suitability of stabilized soil as a base course in flexible pavements was investigated. The lateritic soil was treated with 15, 20, 25 and 30% of GGBS and alkali solutions consisting of 5% of Sodium oxide with Silica Modulus (Ms) of 0.5, 1.0 and 1.5 at a constant water binder ratio of 0.25. The improved unconfined compressive strength, flexural strength, and fatigue life were observed from the soil treated with 30% of GGBS and alkali solution having Ms 1.0 air-cured for 28 days at ambient temperature. The improvement is due to the formation of Calcium Silicate Hydrates and Calcium Alumino Silicate Hydrates from an exothermic reaction between Calcium ions and the dissolved silicates and aluminates present in GGBS and alkali solutions. The samples treated with 25, 30% of GGBS and alkali solution having 1.0 Ms cured for 28 days found to be durable in Wetting-Drying and Freezing-Thawing tests. The compact and densified crystal orientation of the treated soil samples was observed from the microstructure images obtained from the Scanning Electron Microscope technique. The design of low and high volume roads was suggested with stabilized soil and strains developed at different locations on the proposed pavement were analyzed using pavement analysis software. © 2020, Chinese Society of Pavement Engineering. Production and hosting by Springer Nature.Item Nanoindentation and nano-scratch testing on cement paste(ICE Publishing, 2023) Barbhuiya, S.; Das, B.B.Carbon nanotubes are an attractive reinforcement material for several composites. This is due to their inherently high tensile strength and high modulus of elasticity. This study focused on the nanomechanical characteristics of cement paste with and without short multi-walled carbon nanotubes (MWCNTs). The objective behind studying the nanomechanical properties of cement paste is to better understand the fundamental behaviour of cement at the nanoscale level. Cement paste is a complex material that consists of various phases, including cement hydrates, unhydrated cement particles and porosity. By studying the mechanical properties of cement paste at the nanoscale, researchers can gain insights into the mechanisms that govern the behaviour of this material. Following earlier tests, the amount of MWCNTs was kept constant (0.30% by weight of cement). The nanomechanical parameters explored included the localised Young's modulus and hardness. According to the test results, short MWCNTs increased the proportion of high-density calcium silicate hydrate in the cement paste. The nanomechanical properties (localised Young's modulus and hardness) of cement paste with short MWCNTs were found to be greater than those of cement paste without MWCNTs. According to nano-scratching experiments, the cement matrix with short MWCNTs was substantially more durable than the matrix without them. © 2023 Emerald Publishing Limited: All rights reserved.Item One-part eco-friendly alkali-activated concrete – An innovative sustainable alternative(Elsevier Ltd, 2023) Rakesh Kumar Reddy, R.; Yaragal, S.C.; Srinivasa, A.S.The primary objective of this study is to develop an eco-friendly one-part alkali-activated concrete (OPAAC) by incorporating a combination of fly ash (FA), ground granulated blast furnace slag (GGBS), and micro silica (MS). In this investigation, the proportion of MS is maintained at 20% of FA, while the maximum replacement of FA with GGBS is set to 60%, varying in 20% intervals (i.e., 0%, 20%, 40%, and 60%). Further, the natural aggregates (NA) are substituted with recycled coarse aggregates (RCAs), ferrochrome slag aggregates (FCSAs), or a combination of both. The influence of GGBS and alternative aggregates (RCAs, FCSAs) on the mechanical properties of OPAAC is thoroughly examined. To provide a comprehensive assessment, the properties of OPAAC are compared against Ordinary Portland Cement (OPC) concrete (CC) of equivalent grades. Additionally, microstructural and mineralogical investigations are conducted to determine the formation of distinct hydration products, utilizing scanning electron microscopy (SEM) and X-ray diffractometry (XRD) techniques. In OPAAC containing FA, the primary hydration products identified are alkaline alumino silicate hydrates (CASH and NASH). As the GGBS content increases, calcium silicate hydrate (CSH) becomes the predominant hydration product. Furthermore, in order to assess the sustainability of OPAAC, an analysis of embodied CO2 emissions is performed, and the results are compared with CC and alkali-activated concrete. Notably, OPAAC comprising 40% FA replaced with GGBS, 50% RCAs, and 50% FCSAs demonstrates the most favourable mechanical properties and exhibits lower CO2 emissions. © 2023 Elsevier LtdItem Effect of Iron Ore and Copper Ore Tailings on Engineering Properties and Hydration Products of Sustainable Cement Mortar(ASTM International, 2024) Sumukh, E.P.; Das, B.B.; Barbhuiya, S.The prohibition of river sand mining has drawn the attention of researchers in finding practicable alternatives. In the approach of finding these alternatives, it is essential to ensure minimal or zero impairment to the ecological balance, which can be mainly attained by making use of industrial waste/byproducts. The wastes from the mining industry are the major contributors in causing impairment to the environment, and their influence on the stability of mortars on using as fine aggregates needs to be systematically investigated with the view of long-term performance concerns. Thus, the present study explores the applicability of mine tailings and finding the optimum dosage in cement mortars by investigating the engineering properties and microstructure development with the aid of qualitative and quantitative analysis associated with hydration products. The studies confirm that the increased consumption of portlandite for secondary hydration reactions followed by the additional formation of calcium silicate hydrate (CSH) and calcium aluminum silicate hydrate (CASH) phases in mine tailing-based mortars helped in achieving a quality microstructure. These additional formations of CSH and CASH phases are also confirmed through Fourier transform infrared spectroscopy by identifying the shift of Si-O-Si stretching vibration bands toward a lower wavenumber. The lowering of calcium/silicate atomic ratio and increased formation of mineralogical compounds related to CSH and CASH in x-ray diffraction patterns also confirms the same. Gismondine, chabazite, and hillebrandite are the additional phases formed and found to take part in refining the pore structure. This enhanced performance of mine tailing mortars was also verified with the aid of a modified Andreasen and Andersen particle packing model. The formation of high-quality microstructure is reflected in the hardened properties of optimized cement mortar in the proportion of 20 % for iron ore tailing and 30 % for copper ore tailing. © © 2024 by ASTM International.Item Assessment of fly ash and ceramic powder incorporated concrete with steam-treated recycled concrete aggregates prioritising nano-silica(Springer Nature, 2024) Rao, A.U.; Shetty, P.P.; Bhandary, R.; Tantri, A.; S., S.; Yaragal, S.C.Present research involves determining the effects of a proposed novel nano-silica prioritized-steam-treated recycled concrete aggregate (RCA) on microstructural, mechanical, and durability aspects of concrete incorporated with waste ceramic powder (WCP). The study on novel nano-silica prioritized-steam-treated recycled concrete aggregate revealed that 3% nano-silica induction with 3-h steam treatment for 50% adhered mortar bonded RCA performed optimally. The physical characterization of treated RCA showed improvement compared to untreated RCA, which was confirmed by microstructure study indicating the formation of additional calcium silicate hydrates in the bonded adhered mortar of treated RCA. Furthermore, as WCP has significant contents of alumina and silica, an optimum ternary binder mix was developed with cement, fly ash, and WCP. Later, a study was performed to analyse the performance of treated RCA incorporated in WCP prioritized concrete mix. The mechanical performance of WCP prioritized concrete with treated RCA was investigated through compressive strength, flexural strength, split tensile strength, and modulus of elasticity. The quality was ensured through ultrasonic pulse velocity, water absorption, and density characterization. The durability of concrete was studied with 5% concentrated hydrochloric acid attack and sea water (pH = 8.3 to 8.7) exposure conditions for a duration of 148 days (including 28 days of portable water curing period). Overall, 30% of the ternary mixture based on WCP prioritization, 50% adhere mortar-based RCA, and 3% of nano-silica prioritization steam treatment (3 h) demonstrated the best performance in terms of both mechanical and durability aspects. The study concluded that due to its improved performance, the innovative nano-silica priority steam treatment approach could replace 100% of RCA in concrete. Furthermore, treated RCA being advantageous because of easy adoptable technique for real-time practices as well as maintaining consistency regards RCA characteristics throughout concrete mixture be the challenge. © The Author(s) 2024.