Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Preparation and characterization of polysulfone and modified poly isobutylene-alt-maleic anhydride blend NF membrane(2012) Ganesh, B.M.; Isloor, A.M.; Padaki, M.Recently nanofiltration (NF) is gaining more importance for water treatment. It is replacing the conventional method of water treatment due to advantages of NF membranes over RO system. In this work, we are discussing the preparation of NF membrane for desalination of sea water. We herein report the synthesis of polymer, by the reaction of p-amino benzoic acid (PABA) and poly isobutylene-alt-maleic anhydride (PIAM) and its blend membrane preparation with polysulfone (PSf). The new membranes were characterized by SEM images, surface wettability to investigate the hydrophilic nature of the membrane, water swelling, pure water flux, molecular weight cut-off and salt rejection of the membranes. The membranes showed nano size (<50nm) pores in SEM image, and the contact angle data revealed that membrane surface is moderately hydrophilic. Membrane with 70:30 (PSf:modified PIAM) composition has shown good salt rejection of 96% at 200kPa for 3500ppm of NaCl solution with a pure water flux of 38.36Lm -2h -1. © 2011 Elsevier B.V.Item Studies on copper coated polysulfone/modified poly isobutylene alt-maleic anhydride blend membrane and its antibiofouling property(2013) Isloor, A.M.; Ganesh, B.M.; Isloor, S.; A.F., A.F.; Nagaraj, H.S.; Pattabi, M.As nanofiltration is gaining more and more importance in the field of desalination, one has to address the many obstacles in order to achieve effective/efficient filtration. One such issue is biofouling and microbial attack to the membrane. This paper describes about the study on copper coating onto the membrane surface as biofouling protective layer. This is an attempt to come up with a new approach for desalination and an antimicrobial membrane. The work indicates that, the copper coated membrane can resist the possible microbial attack to some extent while maintaining good salt rejection and appreciable flux. SEM and EDX studies had shown the distribution of copper on the membrane surface. The copper coated membrane had shown the maximum salt rejection of about 96% for 3500ppm NaCl solution and also it had shown the pure water flux of 36Lm-2h-1. © 2012 Elsevier B.V.Item Modification of PSf/PIAM membrane for improved desalination applications using Chitosan coagulation media(2013) Kumar, R.; A.F., A.F.; Kassim, M.A.; Isloor, A.M.Polysulfone (PSf)/poly (isobutylene-alt-maleic anhydride) (PIAM) nanofiltration membranes were modified by changing the coagulation bath with various concentrations of glutaraldehyde cross-linked Chitosan solutions. Further the membranes were treated with 0.1N NaOH solution in order to achieve the hydrolysis of PIAM. The morphological changes of the membranes were determined using scanning electron microscope. The blending of PSf/PIAM membrane, the incorporation of Chitosan (CS) molecules in membrane matrix and the hydrolysis of PIAM in the membrane upon alkali treatment were studied by Attenuated Total Reflectance Infra Red (ATR-IR) spectroscopy. The hydrophilicity of modified membranes was measured using the contact angle analyzer. The pressure and time dependent pure water flux of modified PSf/PIAM/CS membranes were measured and compared with PSf/PIAM membranes (after alkali treatment). The antifouling property of membranes was determined using Bovine Serum Albumin (BSA) protein rejection studies. The modified membranes showed improved hydrophilicity and reduced pore size. The order of rejection of membranes for various electrolytes was Na2SO4>MgSO4>NaCl at minimum pressure of 0.2MPa TMP. The antifouling property of modified membranes increased with an increase in the composition of Chitosan in coagulation bath and membrane M-0.8 showed a maximum fouling resistance ratio of 74%. © 2013 Elsevier B.V.Item Effect of hydrogen addition on the performance and emission parameters of an SI engine fueled with butanol blends at stoichiometric conditions(Elsevier Ltd, 2015) Raviteja, S.; Kumar, G.N.Hydrogen is considered as the best fuel due to its excellent combustion properties. But its use as a fuel is confined by its low energy density. In the present investigation an attempt has been made to utilize some of the benefits of hydrogen by using it as an additive in a butanol fueled engine. The experimental study has been carried out on a 4 stroke, single cylinder, manifold electronic fuel injected (EFI) engine mapped to run at stoichiometric conditions. Butanol blends were chosen as the base fuel due to their higher energy density compared to ethanol. A small fraction of hydrogen was injected into the air stream. The engine was run at 3000 RPM at full load condition. The performance, emission and combustion parameters are compared for four concentrations of butanol (10%, 20%, 30%, and 100% by volume of fuel) and two concentrations of hydrogen (5%, and 10% by volume of air) with gasoline. The results indicated that the efficiency of the engine improved upon hydrogen enrichment. An average of 60% reduction was observed in HC and CO emissions with 10% enrichment of hydrogen, whereas the NO emissions almost doubled itself. The combustion analysis showed reduced delay periods, shorter combustion durations, higher cylinder pressures, higher temperatures and improved combustion. © 2015 Hydrogen Energy Publications, LLC.Item Favorable influence of mPIAM on PSf blend membranes for ion rejection(Elsevier B.V., 2017) Jyothi, M.S.; Soontarapa, K.; Padaki, M.; Balakrishna, R.G.; Isloor, A.M.The study reports the use of a novel membrane for heavy metal removal and salt rejection. Poly isobutylene alt maleic anhydride (PIAM) modified by sulfanilic acid is blended with polysulfone (PSf) in different concentrations. This induces surface charge and hydrophillicity in the otherwise hydrophobic PSf membranes. The so modified polymers and their blends are characterized by spectroscopic and microscopic techniques. Blend membranes show drastically enhanced performance with respect to water flux, water uptake and ion exchange capacity. SEM micrographs indicate the hydrophilic domains, –SO3H groups in the polymer to have formed cavities during phase inversion process, thus enhancing permeability. 100% rejection of PEG 2000 and 59% of NaCl rejection substantiated the nature of the membrane to be nanofiltration (NF) type. The prepared membranes were further evaluated for Cr (VI) removal, with removal efficiency reaching above 92%. The electronic coupling that occurs between SO3H? and Na+ and the electrostatic interaction between metal ions and the charge on membrane facilitates NaCl and Cr (VI) rejection respectively. The study gains significance in use of such modified PIAM as blend material with any other polymer to enhance the native properties of the blend membrane. © 2017 Elsevier B.V.Item Selective dehydration of 1-butanol to butenes over silica supported heteropolyacid catalysts: Mechanistic aspect(Elsevier B.V., 2021) Kella, T.; Vennathan, A.A.; Dutta, S.; Mal, S.; Shee, D.Butenes are considered as important olefinic building block to produce fuels/fuel additives and commodity chemicals. In the present investigation, selective dehydration of 1-butanol to butenes was studied in a continuous-flow fixed-bed reactor using various silica-supported heteropolyacid (HPA) catalysts such as phosphotungstic acid (PTA), silicotungstic acid (STA), phosphomolybdic acid (PMA), and silicomolybdic acid (SMA) as the solid acid catalysts. The physicochemical properties of these HPA were determined by BET, powder XRD, FTIR, NH3-TPD, and Py-FTIR. The acid strength and Brønsted/Lewis (B/L) acid ratio were increased with higher loading of HPA on silica. The nature of HPA (addenda and hetero atom) and loading of HPA are important factors for the dehydration of 1-butanol and selectivity towards butenes. PTA and STA showed superior catalytic activity than PMA and SMA. The reaction temperature and WHSV also strongly affected the butanol conversion and selectivity of butenes. The selectivity of di-n?butyl ether decreases with the rising temperature from 523 K to 623 K. The isomerization of 1-butene leading to the formation of other butene isomers depends on the HPA loading, temperature, and WHSV. The presence of molybdenum addendum atom in PMA and SMA promotes dehydrogenation and hydrogenation, leading to the formation of various light hydrocarbons. The 20PTA/SiO2 catalyst afforded 99.8% selectivity towards butenes at quantitative conversion of 1-butanol, whereas the 20STA/SiO2 catalyst gave nearly 97.0% conversion of 1-butanol and 99.9% butenes selectivity at 673 K, 37.4 h?1 of WHSV. © 2021