Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Steam as coolant and lubricant in turning of metal matrix composites(2008) Shetty, R.; Pai B, R.B.; Kamath, V.; Rao, S.S.Green cutting has become focus of attention in ecological and environmental protection. Steam is cheap, pollution-free and eco-friendly, and then is a good and economical coolant and lubricant. Steam generator and steam feeding system were developed to generate and feed steam. Comparative experiments were carried out in cutting AA6061-15 vol.% SiC (25 ?m particle size), with cubic boron nitride (CBN) insert KB-90 grade under the conditions of compressed air, oil water emulsion, steam as coolant and lubricant, and dry cutting, respectively. The experimental results show that, with steam as coolant and lubricant, gradual reduction in the cutting force, friction coefficient, surface roughness and cutting temperature values were observed. Further, there was reduction in built up edge formation. It is proved that use of water steam as coolant and lubricant is environmentally friendly. © 2008 Zhejiang University and Springer-Verlag GmbH.Item An investigation on the properties of boron modified Cu–Al–Be polycrystalline shape memory alloys(Elsevier Ltd, 2020) Bala Narasimha, G.; Murigendrappa, S.M.Effect of microalloying of boron (B) i.e., 0.02–0.15 wt% and the variation of composition of Al and Be from 11.3 to 11.9 wt% and 0.41–0.44 wt% respectively, has been investigated on the grain refinement and shape memory properties of polycrystalline Cu–Al–Be shape memory alloy. The tests have been carried out for microstructure, morphology, phases, crystal structure, phase transformation temperatures and shape recovery ratio. The investigation results in boron has strong impact on grain refinement with minimal addition, followed by Al and Be. AlB2 acts as heterogeneous nucleation site in grain refinement and it increases with increase in B and Al. Transformation temperatures increases with boron up to 0.08 wt% and then decreases, whereas increase in Al and Be decreases the temperatures. Doping and increasing of boron up to 0.15 wt% exhibits complete shape recovery, whereas Be < 0.42 wt% and Al < 11.8 wt% exhibits poor recovery ratio. © 2020 Elsevier B.V.Item Detection of acceptor-bound exciton peak at 300 K in boron–phosphorus co-doped ZnMgO thin films for room-temperature optoelectronics applications(Elsevier B.V., 2021) Sushama, S.; Murkute, P.; Ghadi, H.; Pandey, S.K.; Chakrabarti, S.It is well-known that the ZnMgO thin-film faces a roadblock in its potential applications for various optoelectronic devices due to the limitation imposed on achieving p-type conduction. The mono-acceptor doping of ZnMgO endures from the stern self-compensation by native donor defects and deep acceptor level formation advocating the need for alternate doping techniques like co-doping. In this paper, we report a detailed study on the improvement in structural, elemental, and optical properties of phosphorus-doped Zn0.85Mg0.15O thin films, with an aim to obtain enhancement in the signatures of acceptor-doped behavior, under the influence of boron implantation time. In addition, the paper also captures the behavior exhibited by the co-doped samples as a result of the variation in the annealing temperature. The solubility of the phosphorus atom (acceptor dopant) was observed to improve with boron (donor co-dopant) implantation as confirmed by the structural, elemental, and optical properties of co-doped ZnMgO thin films. It was also found that the acceptor level emissions got improved after boron implantation in phosphorus-doped ZnMgO thin films. Additionally, with co-doping, the sample showed the signature of acceptor-bound exciton peak till 300 K, evidencing the room-temperature operability of the films. Moreover, the fabricated film had a shallow acceptor energy level located at around 74 ± 0.45 meV above the valence band. Co-doped samples also showed stable acceptor based optical emission for more than a year. © 2020 Elsevier B.V.Item Free vibration and inherent material damping characteristics of boron-FRP plate: Influence of non-uniform uniaxial edge loads(EDP Sciences, 2021) Gunasekaran, V.; Jeyaraj, J.; Mailan Chinnapandi, L.B.The current investigation presents the analytical investigation on free vibration and inherent material damping of boron-FRP plate, subjected to non-uniform uniaxial edge loads. Initially critical buckling load (Pcr) is obtained, then followed by free vibration response and inherent material damping values for corresponding modal indices of the FRP plate is calculated for different load fraction of non-uniform uniaxial edge loads. The buckling load and free vibration response are obtained by using strain energy method and Reddy's TSDT respectively. It is observed that the nature of load and aspect ratio influence the bucking, free vibration and inherent material damping behaviour of the fibre reinforced polymer plate significantly. © V. Gunasekaran et al., Published by EDP Sciences, 2021.Item Pseudoelastic Behavior of Boron-Doped ?1 -Type Cu-Al-Be Shape Memory Alloys(Springer, 2021) Kalinga, T.; Murigendrappa, S.M.; Kattimani, S.This paper examines the influence of 0-0.2 wt.%B-doping on the microstructure, mechanical properties, and pseudoelastic behavior of Cu-Al11.5-Be0.57 shape memory alloys (SMAs). This microstructure study reveals that the addition of boron leads to significant grain refinement in ?1-type polycrystalline Cu-Al-Be SMAs. A maximum refinement size of 50 µm was achieved with the addition of 0.15 wt.%B. The fine-grained (Cu-Al11.5-Be0.57)-B0.15 SMA with serrated grain boundaries exhibited the maximum enhancement of ultimate tensile strength, 744.65 ± 29.34 MPa, and ductility of 21.93 ± 0.56%. The fracture morphology revealed the transformation of intergranular to transgranular fracture in the SMAs with boron-doping. Maximum pseudoelasticity of 4% was achieved in the SMA with 0.15 wt.%B and suits as a damper in seismic applications. © 2021, ASM International.Item Photocatalytic degradation of ciprofloxacin & norfloxacin and disinfection studies under solar light using boron & cerium doped TiO2 catalysts synthesized by green EDTA-citrate method(Elsevier B.V., 2021) Manjunatha, M.; Chandewar, P.R.; Mahalingam, H.The presence of antibiotic residues in water bodies is an emerging global concern due to its potential development of antimicrobial resistance. Hence, it is essential to develop photocatalysts that not only degrade the antibiotics but can also simultaneously disinfect. Four different boron and cerium doped TiO2 photocatalysts, synthesized by the EDTA-citrate method, are studied for the degradation of two common fluoroquinolone-based antibiotics: ciprofloxacin (CIP) and norfloxacin (NOR) under sunlight. The catalysts are characterized by SEM, TEM, Raman spectroscopy, XPS, DRS, BET surface area and particle size analyzer. At optimized conditions, the synthesized catalysts showed 90–93% degradation for both CIP and NOR. The effects of catalyst loading and initial concentration are studied, and the reaction is found to be pseudo-first-order. The degradation is analyzed by COD reduction and LC–MS, and the by-products of degradation determined. The recycle studies showed that the catalysts are stable up to three consecutive runs. The scavenging experiments indicated e? and OH? as the dominant species responsible for the photocatalytic activity. The disinfection studies using these catalysts under solar light gave 95–99.99% efficiency for E.coli confirming that they are very efficient and can be further exploited for large scale treatment. © 2020 Elsevier B.V.Item Enhancement in structural, elemental and optical properties of boron–phosphorus Co-doped ZnO thin films by high-temperature annealing(Elsevier B.V., 2021) Sushama, S.; Murkute, P.; Ghadi, H.; Pandey, S.K.; Chakrabarti, S.The inherent n-type nature of zinc oxide (ZnO) and its unstable p-type behavior with single dopant species have encouraged researchers to explore the effect of multiple dopants as a viable solution for long-term stability and repeatability. Herein, we report boron (B) and phosphorus (P) co-doped ZnO thin films engineered through an optimized ion implantation technique followed by annealing at 1000 °C in oxygen ambiance. We investigated their structural, chemical, and optical properties to capture the effect of both boron implantation duration and annealing temperature. Co-doping with boron was observed to boost phosphorus incorporation in the film. Compared with P-doping, P–B co-doping increased the dominance of acceptor-bound exciton peak and also, suppressed non-radiative/visible emission which is due to reduced Madelung energy. After high-temperature annealing at 1000 °C, further narrowing of optical emission peaks generated due to acceptor incorporation was observed. Also, the co-doped samples showed stability in the acceptor behavior for more than one year. © 2021 Elsevier B.V.Item An experimental evaluation of the microstructure, mechanical and functional fatigue properties of the boron-doped Cu-Al-Be SMA wires(Elsevier Ltd, 2021) Singh, R.K.; Biswas, P.; Murigendrappa, S.M.; Kattimani, S.An experimental evaluation of the microstructure, mechanical and functional fatigue properties of the Cu-11.70Al-0.45Be doped with Bx (x = 0.05, 0.10, 0.12, and 0.14 wt%) SMA wires has been carried out. The experiments were performed to investigate microstructure, phase/precipitates, and transformation temperatures for both as-cast and wire samples. Furthermore, tensile properties, shape recovery ratio, and functional fatigue evaluation have also been carried out for the wire samples. The investigation shows that the addition of the minor amount of boron and secondary processes involved during the specimen preparation induced excellent grain refinement. The addition of boron decreased transformation temperatures; however, there was not a considerable change observed due to the secondary process. It was observed that tensile properties increases with the boron addition, and complete shape recovery was observed for all the selected alloys. Finally, functional fatigue tests were conducted under constant stress condition and observed that the number of cycles until the failure has increased and more distance recovery was achieved with an increase in boron doping. © 2021