Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
32 results
Search Results
Item Recuring studies on concretes subjected to elevated temperatures and suddenly cooled by water quenching(Multi-Science Publishing Co. Ltd, 2015) Yaragal, S.C.; Kittur, M.M.; Babu Narayan, K.S.Concrete is found to undergo degradation when subjected to elevated temperatures during an accidental event, such as fire and lose substantial amount of its original strength. The loss of strength in concrete is mainly attributed to the decomposition of Calcium Silicate Hydrate (C-S-H) and release of chemically bound water, which begins when the exposure temperature exceeds 500°C. When such a concrete is supplied with water and allowed to recure, it is found to recover substantial amount of its lost strength. This work is carried out to investigate the effect of recuring on strength recovery of un-blended and blended concrete specimen (100 mm cubes) subjected to elevated temperatures from 400°C to 700°C, in steps of 100°C, for a retention period of two hours at the designated temperatures. The concrete cubes immediately after exposure were subjected to thermal shock by quenching them in water, and then temperature of thermally shocked concrete is allowed to cool to room temperature. The cooled specimen were then recured in water for 1, 3, 7, 14, 21, 28, 56 days and tested for compressive strength recovery. These studies were carried out for Portland Cement (PC) based concrete and Portland & Granulated Blast Furnace Slag (70% PC + 30% GGBS) based concrete (blended concrete), and some interesting results are presented and discussed in this paper. © 2015, Multi-Science Publishing Co. Ltd. All rights reserved.Item Enhancement of the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag(Elsevier Ltd, 2017) Saha, S.; C, C.Research efforts have been made continuously to establish fly ash based geopolymer as an alternative binder material for the production of fresh concrete because production of Ordinary Portland Cement degrades the environment by huge emissions of carbon-di-oxide and also by consuming lot of natural resources. But most of the study reveals, fly ash based geopolymer paste needs more time to get set when it is cured at ambient temperature. As a result, it is quite impractical to use fly ash based geopolymer paste as an alternative to Ordinary Portland Cement in faster construction. In this study, an effort has been made to enhance the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag at various percentage levels. Microstructure of the geopolymer paste is studied using Scanning Electron Microscopy. Result of this investigation shows that significant improvement on setting time and compressive strength can be obtained by adding ground granulated blast furnace slag in the mixes. © 2017 Elsevier LtdItem Influence of Granulated Blast Furnace Slag and Cement on the Strength Properties of Lithomargic Clay(Springer India sanjiv.goswami@springer.co.in, 2017) C. Sekhar, D.C.; Nayak, S.; Preetham, H.K.Utilizing industrial byproducts in soil stabilization benefits the economic, environmental and social benefits. Granulated blast furnace slag is a byproduct of iron and steel industry having oxides similar to that of cement but in different proportions. This study describes experimental results achieved by the use of granulated blast furnace slag (GBFS) and cement in stabilizing lithomargic clay for geotechnical applications. Soil was replaced by GBFS in percentages of 10, 15, 20, 25, 30, 35, 40, 45, 50% and cement of 2, 4, 6, and 8% by dry weight of soil is added. Various experimental studies like specific gravity, Atterberg limits, compaction, UCS, CBR and triaxial compression test, were performed on samples to understand the effect of these mixes on their few index and strength properties. The study also includes an investigation on a combination of optimum percentage of GBFS with varying percentage of cement and lime on their shear parameters. The study result shows significant improvement in the strength properties of the mixes. Hence it can be concluded that lithomargic clay stabilized with GBFS and cement/lime satisfy the strength requisite to be employed in the numerous geotechnical applications. © 2017, Indian Geotechnical Society.Item Utilization of granulated blast furnace slag and cement in the manufacture of compressed stabilized earth blocks(Elsevier Ltd, 2018) C. Sekhar, D.; Nayak, S.This study involves the investigation on utilization of granulated blast furnace slag (GBFS) and cement in the manufacture of compressed stabilized earth blocks (CSEB). Two locally available soils from Dakshina Kannada district, Karnataka, India were tested for their index and strength properties with replacement of granulated blast furnace slag (GBFS). An optimum percentage of replacement of GBFS was established and then varying percentages of cement was added for the production of compressed stabilized earth blocks (CSEBs). This stabilized soil was used for the manufacture of blocks of size 305 mm × 143 mm × 105 mm. All the blocks were cast to a target density, followed by the curing for 28 days. The blocks were subjected to compression test and water absorption test according to Indian Standard (IS) specifications. The test results showed that the CSEBs prepared with GBFS and cement can be utilized in masonry for load bearing wall construction. A small percentage of cement is sufficient for manufacturing the CSEBs when optimum GBFS content is replaced with that of soil, thereby reducing the energy consumption. © 2018 Elsevier LtdItem An experimental investigation on self-compacting alkali activated slag concrete mixes(Elsevier Ltd, 2018) Manjunath, R.; Narasimhan, M.C.In present work, an attempt has been made to develop self-compacting, alkali activated slag concrete mixes, using steel slag sand as fine aggregate and EAF (Electric Arc Furnace) slag as coarse aggregate. The study investigates the properties such as compressive strength, splitting tensile strength and water absorption of these mixes. Development of Self-Compacting Alkali Activated Slag Concrete mixes (hereafter referred to as SCAASC mixes) was made with GGBFS (Ground Granulated Blast Furnace Slag) as the binder, with its content varying between 700 kg/m3 and 900 kg/m3 of fresh concrete. The net W/B (water to binder) ratio of the mixes was varied between a narrow 0.47 – 0.48 range. The alkaline solutions had Na2O percentages in the range 7 – 9%, but a constant activator modulus was maintained at 1.0 in all the mixes. In order to optimise the number of trial mixes to be tested, Taguchi's design of experiments methodology was adopted. A total of nine mixes were formulated using Taguchi orthogonal L9 array. Results showed the slump flow values for the mixes greater than 700 mm, with their L–Box ratios and V-Funnel values ranging between 0.90 and 0.95 and 9 – 11 s respectively, satisfying the EFNARC guidelines. Results also showed good compressive strengths (65–80 MPa), split-tensile strengths (2–4 MPa) and low water absorption values in the range of (2%–3%). The microstructural studies such as SEM, EDX and XRD analysis were also carried out, showing denser morphologies clearly indicating effective activation of slag by the alkaline solution. © 2018 Elsevier LtdItem Optimization of ferrochrome slag as coarse aggregate in concretes(Techno Press technop2@chollian.net, 2019) Yaragal, S.C.; Kumar, B.C.; Mate, K.The alarming rate of depletion of natural stone based coarse aggregates is a cause of great concern. The coarse aggregates occupy nearly 60-70% by volume of concrete being produced. Research efforts are on to look for alternatives to stone based coarse aggregates from sustainability point of view. Response surface methodology (RSM) is adopted to study and address the effect of ferrochrome slag (FCS) replacement to coarse aggregate replacement in the ordinary Portland cement (OPC) based concretes. RSM involves three different factors (groUnd granulated blast furnace slag (GGBS) as binder, flyash (FA) as binder, and FCS as coarse aggregate), with three different levels (GGBS (0, 15, and 30%), FA (0, 15, and 30%) and FCS (0, 50, and 100%)). Experiments were carried out to measure the responses like, workability, density, and compressive strength of FCS based concretes. In order to optimize FCS replacement in the OPC based concretes, three different traditional optimization techniques were used (grey relational analysis (GRA), technique for order of preference by similarity (TOPSIS), and desirability function approach (DFA)). Traditional optimization techniques were accompanied with principal component analysis (PCA) to calculate the weightage of responses measured to arrive at the final ranking of replacement levels of GGBS, FA, and FCS in OPC based concretes. Hybrid combination of PCA-TOPSIS technique is foUnd to be significant when compared to other techniques used. 30% GGBS and 50% FCS replacement in OPC based concrete was arrived at, to be optimal. © 2019 Techno-Press, Ltd.Item Studies on development of high performance, self-compacting alkali activated slag concrete mixes using industrial wastes(Elsevier Ltd, 2019) Manjunath, R.; Narasimhan, M.C.; Umesh, K.M.; Kumar, S.; Bala Bharathi, U.K.In the present study, development of a class of High Performance Alkali Activated Slag Concrete mixes (hereafter referred to as HPAASC mixes) is discussed. These mixes are developed using three industrial wastes from Iron and Steel industry. While Ground granulated blast furnace slag (GGBFS) was used as the main binder, in the development of these HPAASC mixes, steel slag sand and Electric Arc Furnace slag (EAF slag) have been employed in the fine aggregate and coarse aggregate fractions of them. Higher flow characteristics, as those of self-compacting concrete mixes, as well as enhanced mechanical strength properties of these mixes are discussed in detail. The alkaline solutions used consist mixtures of sodium hydroxide and sodium silicate solutions, with a constant activator modulus (ratio of SiO2/Na2O) of one maintained in them. Taguchi’ design of experiments methodology was used to reduce the experimental efforts. The formulation of all the mixes developed herein was based on Taguchi's L-9 orthogonal array. Flow and strength properties of a set of nine mixes were used for performance evaluation purposes in an initial, calibration phase. Strength prediction equations were derived based on such results, the predictive capability of which were then assessed and ascertained with actual results of experiments on the next six new mixes, in the prediction phase. Test results indicated a higher flowability values for all the mixes (with slump flows greater than 700 mm), good filling and passing abilities, all satisfying the EFNARC (European Federation of Specialist Construction Chemicals and Concrete Systems) recommendations for SCC mixes. Higher compressive strengths (65–90 MPa), split-tensile strengths (4.8–5.3 MPa), flexural strengths (6.5–7 MPa), and Modulus of Elasticity (30.4–36.2 GPa) were observed along with lower water absorption values (2.1–2.7%) for all the HPAASC mixes tested herein. Microstructure studies were conducted on samples from the fractured surfaces of test specimens from different mixes, using advanced SEM, EDX and XRD analyses and the results are discussed. © 2018 Elsevier LtdItem A study on initial setting time and the mechanical properties of AASC using the PS ball as fine aggregate(Springer, 2019) Talkeri, A.H.; Ravi Shankar, A.U.India is the second largest producer of cement in the world with an annual production of 455 Million Tonnes (MT) which is expected to reach up to 550MT by 2020. In India, the increased demand for cement in the construction industry is required to meet the needs of infrastructure development. However, the production of Portland cement releases significant amounts of CO2 to the atmosphere. Therefore, it is necessary to look for sustainable solutions for concrete production by the use of supplementary cementitious materials. The alternative replacement for Ordinary Portland Cement (OPC) can be Ground Granulated Blast Furnace Slag (GGBS), Fly-ash, Silica fume, Rice-husk ash, which is the various industrial by-products. In this present work, an attempt was made to develop Alkali Activated Slag Concrete (AASC) using Precious Slag (PS) ball as fine aggregate. The development of AASC was made with GGBS as the principal binder. Mixes were developed with binder content 443 kg/m3, Sodium Silicate (SS)/Sodium Hydroxide (SH) ratio of 1 and their performance when exposed to ambient temperature were studied. Alkali binder ratio (0.3) with 8, 10, 12 and 14M NaOH was selected for all the AASC mixes. The test results showed that the slump values for the different mixes satisfying the MoRTH guidelines for concrete pavements. The AASC mixes have higher compressive strength ranging between 41–64 MPa. The fatigue life of the AASC mix was has improved by the addition of PS ball, at the higher concentration of NaOH. © 2019, Chinese Society of Pavement Engineering. Production and hosting by Springer Nature.Item Geotechnical Investigations on Marine Clay Stabilized Using Granulated Blast Furnace Slag and Cement(Springer, 2019) Preetham, H.K.; Nayak, S.Marine clay is present along the coastal region all around the world. This soil is highly problematic and unfit to support any engineering structures. They are characterized by high liquid limit, high plasticity index with low shear strength and high compressibility. The primary by-product generated from the ferrous industry is granulated blast furnace slag (GBFS), and CaO present in GBFS acts as a binding agent. This paper describes the detailed experimental results by incorporation of GBFS and cement to the marine clay. Soil was replaced by GBFS in various percentages (10%, 20%, 30%, 40% and 50%) and addition of cement (2%, 4%, 6%, 8% and 10%) in percentage of dry weight of soil. Soil and various mixtures are examined for its geotechnical properties, which include specific gravity, consistency limits, compaction characteristics, unconfined compression strength and strength parameters. From the unconfined compression test results, 40% GBFS replacing the marine clay is concluded as the optimum mix. Improvement in the strength is due to the formation of CSH, CAH, CASH and other cementitious compounds which are observed in SEM and XRD studies. From the investigation, it is concluded that GBFS with or without cement can be used as a potential stabilizer for soft marine clay. © 2019, Springer Nature Switzerland AG.Item Use of Stabilized Lateritic and Black Cotton Soils as a Base Course Replacing Conventional Granular Layer in Flexible Pavement(Springer, 2020) Amulya, S.; Ravi Shankar, A.U.The present work investigates the improved properties of lateritic and black cotton soils stabilized with ground granulated blast furnace slag (GGBFS) and alkali solutions. The alkali solution includes a mixture of sodium hydroxide and sodium silicate. The lateritic and black soils are treated with 30% GGBFS and the alkali solutions consisting of 6% Na2O having silica modulus (Ms) of 0.5, 1.0 and 1.5 at a constant water binder ratio of 0.25. The treated samples were air-cured for 0 (immediately after casting), 3, 7 and 28 days at ambient temperature. The treated lateritic soil with 0.5 and 1.0 Ms is found durable after 3, 7, and 28 days curing. Whereas, the treated BC soil found durable with Ms 0.5 at modified Proctor density after 28 days curing. The formation of calcium silicate hydrate and calcium aluminosilicate hydrate structures resulted in a remarkable improvement of compressive strength, flexure and fatigue life of treated soils due to dissolved calcium ions from GGBFS, silicate and aluminium ions from alkali solutions. The microstructure image of the durable soil sample shows the crystal orientation of particles. The design of high and low volume roads is proposed by replacing the conventional granular layer with the durable stabilized soil and stress–strain analysis is carried out using pavement analysis software. © 2020, Springer Nature Switzerland AG.