Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Subject: search.filters.subject.Biodegradable composites

Search Results

Now showing 1 - 3 of 3
  • No Thumbnail Available
    Item
    Free Vibration of Flax Braided Fabric PLA Beam under Edge Compression
    (Taylor and Francis Ltd., 2022) Kanakannavar, S.; Jeyaraj, J.
    The present study focuses on the development of biodegradable composites to replace synthetic polymer-based composites for potential lightweight structural applications in the automobile, aeronautical, marine, and packaging industries. Initially, PLA and NFBF/PLA films are prepared by solution casting, and from these films, composite laminates are prepared by film sequencing and compression (hot-press) molding methods. First, the critical buckling load (Pcr) of composites is analyzed, and then, the influence of compressive load on natural frequency is studied. The critical buckling load-bearing capacity of PLA is enhanced with the reinforcement of NFBF (natural fiber braided yarn fabric). The composite with three layers of NFBF registered the highest critical-buckling load (Pcr) of 374.19 N, and this value is 172.13% high compared to the virgin PLA. Similarly, the natural frequency of the NFBF composites approaches minimum when the applied load is equal to the corresponding Pcr. However, a significant increase in the fundamental frequency is noticed when the applied load is higher than the Pcr. © 2021 Taylor & Francis.
  • No Thumbnail Available
    Item
    Biodegradation properties and thermogravimetric analysis of 3D braided flax PLA textile composites
    (SAGE Publications Ltd, 2022) Kanakannavar, S.; Jeyaraj, J.; Thalla, A.K.; RAJESH, M.
    Recent advances in the development and application of bio-based (natural fiber and biopolymer) composites are gaining broad attention because the resulting polymer completely degrades and does not release harmful substances. In this study, natural fiber 3 D braided yarn textile PLA (Polylactic acid) bio-composites are developed by film sequencing followed by hot-press compression molding. Bio-deterioration and thermal stability of the composites are analysed for storage, machining, transportation, and in-service uses in different environmental conditions (compost and thermal). Composite samples with different fiber wt.% (0, 22, 44) are exposed to compost soil. Tensile testing is performed under different configurations to characterise the tensile properties. Prepared bio-composite specimens are evaluated for weight loss and reduction in tensile properties over soil burial time, to observe the rate of biodegradation of braided yarn textile bio-composites. Fourier transform infrared (FTIR) and scanning electron microscopy (SEM) is employed to analyse the biodegradability of the composites. To study the thermal stability of the prepared bio-composites thermogravimetric (TG) analysis is carried out. Results showed that biodegradability, tensile properties and thermal stability of the composites are enhanced significantly with the reinforcement of 3 D braided yarn fabric. © The Author(s) 2021.
  • No Thumbnail Available
    Item
    Tensile Behaviour of Double-Edge Notched Flax Braided Yarn Woven Fabric Reinforced PLA Composite
    (Korean Fiber Society, 2023) Kanakannavar, S.; Pitchaimani, J.; Goh, K.-L.
    Biodegradable composites were fabricated from poly-lactic acid (PLA) reinforced by flax braided-yarn woven fabric. Composites with different fabric content (corresponding to the 1, 2 and 3 layers of fabric respectively) were obtained by solution casting and compression moulding processes. Tensile fracture properties were evaluated using the double-edge-notch-tension (DENT) test. A scanning electron microscope was used to look at the fractographic features. Reinforcement of braided-yarn fabric resulted in enhanced tensile fracture strength (σf) and toughness of PLA composite. Fracture toughness (KIC) of the composite improved with the fibre contents, namely 64, 79 and 89%, which correspond to 1, 2 and 3 layers of fabric. The improvement in the tensile fracture characteristics of the composites could be contributed by the presence of an effective interfacial bonding of fibre matrix. © 2023, The Author(s), under exclusive licence to the Korean Fiber Society.