Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Nanohydroxyapatite Reinforced Chitosan Composite Hydrogel with Tunable Mechanical and Biological Properties for Cartilage Regeneration(Nature Publishing Group Houndmills Basingstoke, Hampshire RG21 6XS, 2019) Kumar, B.Y.S.; Isloor, A.M.; Mohan Kumar, G.C.M.; Siddique, I.; Asiri, A.M.With the continuous quest of developing hydrogel for cartilage regeneration with superior mechanobiological properties are still becoming a challenge. Chitosan (CS) hydrogels are the promising implant materials due to an analogous character of the soft tissue; however, their low mechanical strength and durability together with its lack of integrity with surrounding tissues hinder the load-bearing application. This can be solved by developing a composite chitosan hydrogel reinforced with Hydroxyapatite Nanorods (HANr). The objective of this work is to develop and characterize (physically, chemically, mechanically and biologically) the composite hydrogels loaded with different concentration of hydroxyapatite nanorod. The concentration of hydroxyapatite in the composite hydrogel was optimized and it was found that, reinforcement modifies the hydrogel network by promoting the secondary crosslinking. The compression strength could reach 1.62 ± 0.02 MPa with a significant deformation of 32% and exhibits time-dependent, rapid self-recoverable and fatigue resistant behavior based on the cyclic loading-unloading compression test. The storage modulus value can reach nearly 10 kPa which is needed for the proposed application. Besides, composite hydrogels show an excellent antimicrobial activity against Escherichia coli, Staphylococcus aureus bacteria’s and Candida albicans fungi and their cytocompatibility towards L929 mouse fibroblasts provide a potential pathway to developing a composite hydrogel for cartilage regeneration. © 2019, The Author(s).Item Degradation, wettability and surface characteristics of laser surface modified Mg–Zn–Gd–Nd alloy(Springer, 2020) K.r, R.; Bontha, S.; M.r, R.; Das, M.; Balla, V.K.This work evaluates the effects of laser surface modification on Mg–Zn–Gd–Nd alloy which is a potential biodegradable material for temporary bone implant applications. The laser surface melted (LSM) samples were investigated for microstructure, wettability, surface hardness and in vitro degradation. The microstructural study was carried out using scanning and transmission electron microscopes (SEM, TEM) and the phases present were analyzed using X-ray diffraction. The in vitro degradation behaviour was assessed in hank’s balanced salt solution (HBSS) by immersion corrosion technique and the effect of LSM process parameters on the wettability was analyzed through contact angle measurements. The microstructural examination showed remarkable grain refinement as well as uniform redistribution of intermetallic phases throughout the matrix after LSM. These microstructural changes increased the hardness of LSM samples with an increase in energy density. The wetting behaviour of processed samples showed hydrophilic nature when processed at lower (12.5 and 17.5 J/mm2) and intermediate energy density (22.5 and 25 J/mm2), which can potentially improve cell-materials interaction. The corrosion rate of as cast Mg–Zn–Gd–Nd alloy decreased by ~83% due to LSM. [Figure not available: see fulltext.]. © 2020, Springer Science+Business Media, LLC, part of Springer Nature.Item Mechanical behaviour of additively manufactured bioactive glass/high density polyethylene composites(Elsevier Ltd, 2020) Jeyachandran, P.; Bontha, S.; Bodhak, S.; Balla, V.K.; Kundu, B.; Doddamani, M.Bioactive glass (BAG) is a well-known biomaterial that can form a strong bond with hard and soft tissues and can also aid in bone regeneration. In this study, BAG is added to a polymer to induce bioactivity and to realize fused filament fabrication (FFF) based printing of polymer composites for potential orthopaedic implant applications. BAG (5, 10, and 20 wt%) is melt compounded with high density polyethylene (HDPE) and subsequently extruded into feedstock filament for FFF-printing. Tensile tests on developed filaments reveal that they are stiff enough to resist forces exerted during the printing process. Micrography of printed HDPE/BAG reveals perfect diffusion of raster interface indicating proper selection of printing parameters. Micrography of freeze fractured prints shows the homogeneous distribution and good dispersion of filler across the matrix. The tensile, flexural, and compressive modulus of FFF-printed HDPE/BAG parts increases with filler addition. BAG addition to the HDPE matrix enhances flexural and compressive strength. The tensile and flexural behaviour of FFF-prints is comparable to injection molded counterparts. Property maps exhibit the merits of present study over the existing literature pertaining to desired bone properties and polymer composites used in biomedical applications. It is envisioned that the development of HDPE/BAG composites for FFF-printing can lead to possible orthopaedic implants and scaffolds to mimic the bone properties in customised anatomical sites or injuries. © 2020 Elsevier LtdItem Evaluation of implant properties, safety profile and clinical efficacy of patient-specific acrylic prosthesis in cranioplasty using 3D binderjet printed cranium model: A pilot study(Churchill Livingstone, 2021) Basu, B.; Bhaskar, N.; Barui, S.; Sharma, V.; Das, S.; Govindarajan, N.; Hegde, P.; Perikal, P.J.; Antharasanahalli Shivakumar, M.; Khanapure, K.; Jagannatha, A.There exists a significant demand to develop patient-specific prosthesis in reconstruction of cranial vaults after decompressive craniectomy. we report here, the outcomes of an unicentric pilot study on acrylic cranial prosthesis fabricated using a 3D printed cranium model with its clinically relevant mechanical properties. Methods: The semi-crystalline polymethyl methacrylate (PMMA) implants, shaped to the cranial defects of 3D printed cranium model, were implanted in 10 patients (mean age, 40.8 ± 14.8 years). A binderjet 3D printer was used to create patient-specific mould and PMMA was casted to fabricate prosthesis which was analyzed for microstructure and properties. Patients were followed up for allergy, infection and cosmesis for a period of 6 months. Results: As-cast PMMA flap exhibited hardness of 15.8 ± 0.24Hv, tensile strength of 30.7 ± 3.9 MPa and elastic modulus of 1.5 ± 0.1 GPa. 3D microstructure of the semi-crystalline acrylic implant revealed 2.5–15 µm spherical isolated pores. The mean area of the calvarial defect in craniectomy patients was 94.7 ± 17.4 cm2. We achieved a cranial index of symmetry (CIS -%) of 94.5 ± 3.9, while the average post-operative Glasgow outcome scale (GOS) score recorded was 4.2 ± 0.9. Conclusions: 3D printing based patient-specific design and fabrication of acrylic cranioplasty implant is safe and achieves acceptable cosmetic and clinical outcomes in patients with decompressive craniectomy. Our study ensured clinically acceptable structural and mechanical properties of implanted PMMA, suggesting that a low cost 3D printer based PMMA flap is an affordable option for cranioplasty in resource constrained settings. © 2021 Elsevier LtdItem A comprehensive characterization of 3D printable poly ether ketone ketone(Elsevier Ltd, 2024) Ojha, N.; Kumar, S.; Ramesh, M.R.; Balan, A.A.S.; Doddamani, M.The current work focuses on the comprehensive characterization of a 3D printable biomaterial, polyether ketone ketone (PEKK). The PEKK granules are first characterized and then utilized for extrusion of the PEKK filaments. The extruded PEKK filaments are characterized for crystallinity, quality, and printability, wherein they exhibit amorphous nature, good quality, and appropriate printability. Utilizing the filaments, the samples are printed with the appropriate printing parameters, which are further characterized for layer adhesion, voids, and crystallinity, wherein they showed seamless layer adhesion, improper beads consolidation, and the amorphous nature. The as printed samples are further annealed at different temperatures (200 and 250 °C). The scanning electron microscopy (SEM) of the annealed samples (A-200 and A-250) revealed better void consolidation, while the X-ray diffraction (XRD) revealed better crystallinity compared to the un-annealed sample. The printed samples are also investigated for dynamic mechanical analysis (DMA), shape memory, and tensile properties. The storage moduli of the annealed samples are observed to be better than the un-annealed sample. The annealed samples exhibited better shape memory properties: shape fixity and shape recovery ratio of A-200 and A-250 samples, 90.28 and 90.75%, and 99.16 and 94.73%, respectively, compared to the un-annealed samples. The highest shape fixity ratio and the shape recovery ratio are noted for A-250 (90.75%) and A-200 (∼ 100%). The A-200 and A-250 samples showed enhanced tensile modulus and strength, 4.16 and 49.67%, and 36.61 and 35.06%, respectively compared to the un-annealed sample. The highest modulus is noted for A-250, while the strength is comparable (36.61 and 35.06%) for A-200 and A-250. © 2023 Elsevier LtdItem Mango Leaves (Mangifera indica)-Derived Highly Florescent Green Graphene Quantum Dot Nanoprobes for Enhanced On-Off Dual Detection of Cholesterol and Fe2+ Ions Based on Molecular Logic Operation(American Chemical Society, 2024) Ratnesh, R.K.; Singh, M.K.; Kumar, V.; Singh, S.; Chandra, R.; Singh, M.; Singh, J.In the present study, we have engineered a molecular logic gate system employing both Fe2+ ions and cholesterol as bioanalytes for innovative detection strategies. We utilized a green-synthesis method employing the mango leaves extract to create fluorescent graphene quantum dots termed “mGQDs”. Through techniques like HR-TEM, i.e., high-resolution transmission electron microscopy, Raman spectroscopy, and XPS, i.e., X-ray photoelectron spectroscopy, the successful formation of mGQDs was confirmed. The photoluminescence (PL) characteristics of mGQDs were investigated for potential applications in metal ion detection, specifically Fe2+ traces in water, by using fluorescence techniques. Under 425 nm excitation, mGQDs exhibited emission bands at 495 and 677 nm in their PL spectrum. Fe2+-induced notable quenching of mGQDs’ PL intensity decreased by 97% with 2.5 μM Fe2+ ions; however, adding 20 mM cholesterol resulted in a 92% recovery. Detection limits were established through a linear Stern-Volmer (S-V) plot at room temperature, yielding values of 4.07 μM for Fe2+ ions and 1.8 mM for cholesterol. Moreover, mGQDs demonstrated biocompatibility, aqueous solubility, and nontoxicity, facilitating the creation of a rapid nonenzymatic cholesterol detection method. Selectivity and detection studies underscored mGQDs’ reliability in cholesterol level monitoring. Additionally, a molecular logic gate system employing Fe2+ metal ions and cholesterol as a bioanalyte was established for detection purposes. Overall, this research introduces an ecofriendly approach to craft mGQDs and highlights their effectiveness in detecting metal ions and cholesterol, suggesting their potential as versatile nanomaterials for diverse analytical and biomedical applications. © 2024 American Chemical Society.Item High-pressure torsion of biodegradable Mg?Zn?Mn alloy and investigate mechanical and corrosion behaviour(Nature Research, 2025) Kumar, P.; Anne, G.; Ramesh, S.; Kudva, S.A.; Ramesh, M.R.; Doddamani, M.; Prabhu, A.; Sahu, S.Considering their biodegradability in physiological environments and similar elastic modulus to natural bone, magnesium alloys have generated a lot of interest as biodegradable implant materials. Their poor corrosion resistance is primarily a result of the inhomogeneous distribution of their second phase, which limits their clinical application. High pressure torsion (HPT) one of the severe plastic deformation techniques which provides an opportunity to process materials with low formability such as magnesium at room temperature. The present study HPT is conducted for Mg-Zn-Mn alloy up to ten revolutions at room temperature. Optical, scanning, and transmission electron microscopes were used to examine the microstructures of base material (BM) and ten revolution HPT samples. Significant microhardness improvement was observed in HPT N10 samples (222 Hv) as compared to BM samples (68 Hv). It was determined that the improvement in microhardness was primarily due to dislocation strengthening, fine grain strengthening, and second phase strengthening. Potentiodynamic polarisation and electrochemical impedance spectroscopy (EIS) were used in a simulated body fluid (SBF) solution to assess the corrosion behaviour. When compared to the BM sample (0.0243 mm/y), the corrosion resistance of the HPT N10 sample (0.0012 mm/y) increased significantly. This was mostly due to the smaller grain size and uniform dispersion of the secondary phases, which result in a uniform corrosion. Further, obtained data from the cytotoxicity assay carried out using the MTT method indicated the compatibility of the Mg-Zn-Mn alloy on MG-63 osteoblast-like cells, further substantiating its safety on the bone cells. © The Author(s) 2025.Item Assessment of biocompatibility for citric acid crosslinked starch elastomeric films in cell culture applications(Nature Research, 2025) Pooja, N.; Ahmed, N.Y.; Mal, S.S.; Bharath, P.A.S.; Zhuo, G.-Y.; Noothalapati, H.; Managuli, V.; Mazumder, N.This study investigates the synthesis of potato starch elastomers reinforced with silicon dioxide (SiO2) and citric acid as a crosslinking agent to enhance their mechanical and barrier properties. Surface morphology analysis using optical microscopy revealed that pure potato starch films had uneven surfaces. However, higher SiO2 concentrations increased roughness, while citric acid crosslinked films displayed smoother surfaces overall. Water vapor transmission rates (WVTR) indicated that native starch films were highly hydrophilic, while SiO2 incorporation and citric acid crosslinking significantly reduced WVTR of 17% (30% lower than native film), enhancing the barrier properties. Tensile strength testing revealed that citric acid crosslinking increased the tensile strength by 25%, while SiO2 further reinforced the films but decreased elasticity by 15%. SiO2 had little impact on degradation rates, while citric acid crosslinking delayed microbial growth, extending film longevity by 20%. Biocompatibility assays using SiHa, HT-29, and HEK 293 cell lines revealed that the films had varying degrees of cell confluency. Films with both SiO2 and citric acid showed improved confluency (20% higher) compared to films containing only SiO2. However, citric acid alone resulted in the highest confluency (95% viability), suggesting its significant role in biocompatibility. This eco-friendly approach demonstrates substantial advancements in film properties, offering potential applications in diverse biomedical industries. © The Author(s) 2025.