Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
18 results
Search Results
Item Multi-objective optimization of friction welding parameters in AISI 304L austenitic stainless steel and copper joints(SAGE Publications Ltd info@sagepub.co.uk, 2016) Shanjeevi, C.; Kumar, S.S.; Paulraj, P.Friction welding is a solid-state joining technique, and joining of dissimilar materials has been witnessing tremendous development in various applications. In this study, friction welding is carried out in dissimilar materials, austenitic stainless steel and copper, which find application in power generators. The parameters such as friction pressure, upset pressure, rotational speed and burn-off length are considered to determine its influence on tensile strength, metal loss and weld time. Taguchi's L27 orthogonal array is used for experimental design to maximize the tensile strength as well as minimize the metal loss and weld time. Optimal parameters are determined through multiple performance characteristics, and it is found that friction pressure of 22 MPa, upset pressure of 108 MPa, rotational speed of 500 r/min and burn-off length of 1mm yield good mechanical and metallurgical properties. © IMechE 2014.Item Microstructural characterization of low temperature plasma-nitrided 316L stainless steel surface with prior severe shot peening(Elsevier Ltd, 2016) Jayalakshmi, M.; Huilgol, P.; Badekai Ramachandra, B.R.; Bhat, K.U.Surface nanocrystallization by severe deformation has proven beneficial as pre-treatment to plasma nitriding. It aids in achieving thicker nitride layers at lower temperatures thus making the process more economical. In austenitic stainless steels, severe deformation leads to formation of strain induced martensite on the surface while plasma nitriding alone forms expanded austenite. However, structural characteristics of surface layer of pre-deformed steel after plasma nitriding is still a matter of debate. In present study, 316L stainless steel was subjected to severe shot peening: followed by plasma nitriding at 400 °C for 4 h. Characteristics of sample surface before and after treatment were analyzed by scanning electron microscopy, X-ray diffractometry and transmission electron microscopy techniques. Results showed that, this duplex treatment leads to formation of about 45 ?m thick nitride layer; without CrN precipitation. This is significantly high compared to reported data considering the temperature and duration of nitriding treatment employed. Selected area electron diffraction pattern from topmost surface confirmed the co-existence of austenite and martensite while subsurface layer was predominantly consisting of lath martensite. This indicates that major phase in the nitrided layer is martensitic in nature and nitrogen supersaturation leads to transformation of small fraction of martensite to expanded austenite. © 2016 Elsevier LtdItem Effect of shot peening coverage on surface nanostructuring of 316L stainless steel and its influence on low temperature plasma-nitriding(ASTM International, 2017) Jayalakshmi, M.; Badekai Ramachandra, B.; Bhat, K.U.Air-blast shot peening (ABSP) is a cost effective and industrially viable technique to produce nanostructured surface layer on metallic materials. In the present study, 316L stainless steel samples were subjected to shot peening at different peening coverage, from conventional to severe peening. Nanocrystalline structure was observed on the sample surface after peening and mechanical twins; intersection of multidirectional twins producing rhombic blocks were observed in the subsurface layer. Peening process led to the formation of strain induced martensite (?'), and its fraction was found to increase with the coverage. Depth of nanostructured layer and surface microhardness also increased with the increase in coverage, whereas surface roughness followed an opposite trend. Both peened and un-peened samples were subjected to plasma nitriding at 400°C for 4 h. Uniform and appreciably high case depth of about 45 ?m was observed in severely pre-peened (1000 % coverage) sample after nitriding treatment. No precipitation of CrN was observed. This highlights the marked influence of severe shot peening as a pre-treatment for low temperature plasma nitriding of austenitic stainless steels. © © 2017 by ASTM International.Item Tribo-corrosion study of nickel-free, high nitrogen and high manganese austenitic stainless steel(Elsevier Ltd, 2018) Vats, V.; Baskaran, T.; Arya, S.B.The electrochemical corrosion and tribo-corrosion behaviors of nickel-free high nitrogen (HN SS) and high manganese containing austenitic stainless steel were studied in simulated body fluids such as Ringer's and artificial saliva solutions (ASS) using tribo-meter attached with the potentiostat. Type 316L SS used as reference alloy for comparison. Open circuit potential (OCP) and potentiodynamic polarization techniques were used to examine the passivation and corrosion behavior of both the stainless steels under the applied loads of 5 and 10 N at room temperature and also compared with the static condition of corrosion. Pitting resistance of HN SS was found to be significantly higher over type 316L SS. © 2017 Elsevier LtdItem Corrosion resistance and in-vitro bioactivity of BaO containing Na2O-CaO-P2O5 phosphate glass-ceramic coating prepared on 316 L, duplex stainless steel 2205 and Ti6Al4V(Institute of Physics Publishing helen.craven@iop.org, 2018) Edathazhe, A.B.; Shashikala, H.D.The phosphate glass with composition 11Na2O-15BaO-29CaO-45P2O5 was coated on biomedical implant materials such as stainless steel 316 L, duplex stainless steel (DSS) 2205 and Ti6Al4V alloy by thermal enamelling method. The structural properties and composition of glass coated substrates were studied by x-ray diffraction (XRD), Scanning electron microscopy (SEM) and Energy dispersive x-ray spectroscopy (EDS) analysis. The coatings were partially crystalline in nature with porous structure and pore size varied from micro to nanometer range. The polarization curve was obtained for uncoated and coated substrates from electrochemical corrosion test which was conducted at 37 °C in Hank's balanced salt solution (HBSS). The corrosion resistance of 316 L substrate increased after coating, whereas it decreased in case of DSS 2205 and Ti6Al4V. The XRD and SEM/EDS studies indicated the bioactive hydroxyapatite (HAp) layer formation on all the coated surfaces after electrochemical corrosion test, which improved the corrosion resistance. The observed electrochemical corrosion behavior can be explained based on protective HAp layer formation, composition and diffusion of ions on glass coated surfaces. The in-vitro bioactivity test was carried out at 37 °C in HBS solution for 14 days under static conditions for uncoated and coated substrates. pH and ion release rate measurements from the coated samples were conducted to substantiate the electrochemical corrosion test. The lower ion release rates of Na+ and Ca2+ from coated 316 L supported its higher electrochemical corrosion resistance among coated samples. Among the uncoated substrates, DSS showed higher electrochemical corrosion resistance. Amorphous calcium-phosphate (ACP) layer formation on all the coated substrates after in-vitro bioactivity test was confirmed by XRD, SEM/EDS and ion release measurements. The present work is a comparative study of corrosion resistance and bioactivity of glass coated and uncoated biomedical implants such as 316 L, DSS and Ti6Al4V. © 2018 IOP Publishing Ltd.Item High-Temperature Erosive Behavior of Plasma Sprayed Cr3C2-NiCr/Cenosphere Coating(Springer New York LLC barbara.b.bertram@gsk.com, 2018) Mathapati, M.; Doddamani, M.; Ramesh, M.R.This research examines the deposition of Cr3C2-NiCr/cenosphere and Cr3C2-NiCr coatings on MDN 321 steel through the process of plasma spray. In this process, the solid particle erosion test is established at 200, 400, 600 °C with 30° and 90° impact angles. Alumina erodent is adopted to investigate the erosive behavior of the coating at higher temperatures. The properties of the Cr3C2-NiCr/cenosphere coating are established based on the microhardness, the adhesive strength, the fracture toughness, and the ductility. To quantify volume loss as a result of erosion, an optical profilometer is used. At higher temperature, decrease in the erosion volume loss of Cr3C2-NiCr/cenosphere and Cr3C2-NiCr coatings is observed. The erosion-resistive property of Cr3C2-NiCr/cenosphere coating is higher than that of MDN 321 steel by 76%. This property is influenced by high-temperature stability of mullite, alumina, and protective oxide layer that is formed at elevated temperatures. The morphology of eroded coating discloses a brittle mode of material removal. © 2018, ASM International.Item Insights into formation of gradient nanostructured (GNS) layer and deformation induced martensite in AISI 316 stainless steel subjected to severe shot peening(Elsevier B.V., 2018) Jayalakshmi, M.; Huilgol, P.; Badekai Ramachandra, B.R.; Udaya Bhat, K.Severe peening is a well-accepted top-down approach to engender surface nanocrystallization in austenitic stainless steels. In the present study, AISI 316 grade austenitic stainless steel is subjected to severe peening through air blast shot peening technique. Study is aimed at analyzing the microstructural features of the peened layer and deformation induced martensite through transmission electron microscopy technique. Gradient nanostructured (GNS) layer formed as a result of high strain rate, multi-directional deformation during severe peening found to extend to about 500 ?m from the surface. Nucleation of deformation induced martensite is not limited to shear band intersections as affirmed by the published literature related to severe peening. It is observed to nucleate at multiple locations in the austenite matrix. Martensite units thus formed, coalesce with each other to form continuous layer of lath martensite layer at about 15–20 ?m from the surface. Upon further deformation, lath morphology transforms to dislocation cell-type; resulting in fine martensite crystallites at the topmost layer of the peened surface. © 2018 Elsevier B.V.Item Metastable microstructures at the interface between AISI 321 steel and molten aluminum during hot-dip aluminizing(Elsevier B.V., 2018) Huilgol, P.; Udupa, K.R.; Bhat, K.U.The microstructure at the interface between AISI 321 stainless steel and molten aluminum was investigated which occurs during the process of hot-dip aluminizing. Microstructural characterization was carried out by scanning electron microscopy, transmission electron microscopy and X-ray diffraction. The study revealed the formation of metastable FeAlm and multiple twinned Al13Fe4 phases at the interface between steel and aluminum. Multiple twinned Al13Fe4 phase exhibits pseudo tenfold electron diffraction pattern. Another metastable phase Al3(NiFe) with an orthorhombic structure was formed as one of the eutectic phase mixture in the solidified aluminum topcoat. The Al3(NiFe) phase in the eutectic shares crystallographic orientation relationship with the Al matrix. Metastable intermetallic phases are being reported for the first time during hot-dip aluminizing. © 2018 Elsevier B.V.Item On the corrosion resistance of some selective laser melted alloys(Elsevier B.V., 2018) Suryawanshi, J.; Baskaran, T.; Prakash, O.; Arya, S.; Ramamurty, U.The electrochemical corrosion resistances of selective laser melted (SLM) 316 L austenitic stainless steel (SS), 18(Ni) 300-grade maraging steel (MS), and Al-12 wt.% Si (AS) alloy in a 0.1 M NaCl solution at room temperature were evaluated. The effects of laser scanning strategy (single melt vs. checker board styles), post-SLM heat treatment, and corroding surface orientation (with respect to the scan and build directions) on the corrosion behavior were examined. In all cases, results were compared with those obtained on samples with the same compositions, but manufactured using conventional means. The experimental results show that, for the particular set of experimental conditions employed in this study, SLM in general improves the corrosion resistances of Al-12 wt.% Si and stainless steel alloys and degrades the corrosion resistance of the maraging steel, in comparison to the respective corrosion resistances of their conventionally manufactured counterparts. These results are discussed in terms of microstructural refinement and porosity that are common to the SLM alloys. © 2018 Acta Materialia Inc.Item Microstructure and tribological behavior of plasma sprayed NiCrAlY/WC-Co/cenosphere/solid lubricants composite coatings(Elsevier B.V., 2018) Doddamani, M.; Mathapati, M.; Ramesh, M.R.Present investigation deal with NiCrAlY/WC-Co/Cenosphere/MoS2/CaF2, NiCrAlY/WC-Co/Cenosphere/MoS2/CaSO4 and NiCrAlY/WC-Co/Cenosphere coatings deposited on MDN 321 steel using atmospheric plasma spraying. Tribological properties of MDN 321 steel and coatings are evaluated from room temperature (RT) to 600 °C under dry lubrication conditions using a pin on disc high-temperature tribometer. Scanning Electron Microscopy (SEM), X-ray diffraction (XRD) and Energy Dispersive Spectroscopy (EDS) are used to characterize the coatings. Presence of cenospheres in these coatings might effectively reduce wear acting as localized regions accumulating wear debris. The result shows that wear rate of all the coatings are lower as compared to MDN 321 substrate at all the test conditions. NiCrAlY/WC-Co/Cenosphere/MoS2/CaF2 and NiCrAlY/WC-Co/Cenosphere/MoS/CaSO4 coatings registered lower friction coefficient as compared to NiCrAlY/WC-Co/Cenosphere coating and MDN 321 substrate. Characterization of the NiCrAlY/WC-Co/Cenosphere/MoS2/CaF2 and NiCrAlY/WC-Co/Cenosphere/MoS2/CaSO4 coatings worn out surface suggests that MoS2 provides lubrication at 200 °C and formation of CaMoO4, MoO3 through tribo chemistry reaction at higher temperature provides lubrication at 600 °C. SEM micrograph of worn surface demonstrates that the main wear mechanism is plowing and delamination. © 2018 Elsevier B.V.