Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
10 results
Search Results
Item Boiling of saturated water on grooved surface(Serbian Society of Heat Transfer Engineers, 2019) Sathyabhama, A.The flow patterns and pool boiling heat transfer performance of rectangular grooved surface immersed in saturated water were experimentally investigated. The effect of the aspect ratio (groove depth/fin thickness) on boiling performance was examined. The test surfaces were manufactured on a copper block with a base diameter of 19 mm with four fin thickness (0.5 mm, 1mm, 1.5 mm and 2 mm) and three groove depths (1.0 mm, 2.0 mm and 3.0 mm). All experiments were performed in the saturated state at atmospheric pressure. A plain surface was used as the reference standard and compared with the grooved surfaces. The photographic images showed different boiling flow patterns among the test surfaces at various heat fluxes. The test results indicated that closer and more number of grooves yielded a greater flow resistance against the bubble/vapor lift-off along the groove wall. At higher heat flux, numerous vapor mushrooms periodically appeared from the perimeter of the grooves. The developed correlation for Nusselt number predicts the experimental data with MAE of 7.42%. © 2018 Serbian Society of Heat Transfer Engineers.Item Numerical simulation of buckling and asymmetric behavior of flexible filament using temporal second-order immersed boundary method(Emerald Publishing, 2020) Kanchan, M.; Maniyeri, R.Purpose: The purpose of this paper is to perform two-dimensional numerical simulation involving fluid-structure interaction of flexible filament. The filament is tethered to the bottom of a rectangular channel with oscillating fluid flow inlet conditions at low Reynolds number. The simulations are performed using a temporal second-order finite volume-based immersed boundary method (IBM). Further, to understand the relation between different aspect ratios i.e. ratio of filament length to channel height (Len/H) and fixed channel geometry ratio, i.e. ratio of channel height to channel length (H/Lc) on mixing and pumping capabilities. Design/methodology/approach: The discretization of governing continuity and Navier–Stokes equation is done by finite-volume method on a staggered Cartesian grid. SIMPLE algorithm is used to solve fluid velocity and pressure terms. Two cases of oscillatory flow conditions are used with the flexible filament tethered at the center of bottom channel wall. The first case is sinusoidal oscillatory flow with phase shift (SOFPS) and second case is sinusoidal oscillatory flow without phase shift (SOF). The simulation results are validated with filament dynamics studies of previous researchers. Further, parametric analysis is carried to study the effect of filament length (aspect ratio), filament bending rigidity and Reynolds number on the complex deformation and behavior of flexible filament interacting with nearby oscillating fluid motion. Findings: It is found that selection of right filament length and bending rigidity is crucial for fluid mixing scenarios. The phase shift in fluid motion is also found to critically effect filament displacement dynamics, especially for rigid filaments. Aspect ratio, suitable for mixing applications is dependent on channel geometry ratio. Symmetric deformation is observed for filaments subjected to SOFPS condition irrespective of bending rigidity, whereas medium and low rigidity filaments placed in SOF condition show severe asymmetric behavior. Two key findings of this study are: symmetric filament conformity without appreciable bending produces sweeping motion in fluid flow, which is highly suited for mixing application; and asymmetric behavior shown by the filament depicts antiplectic metachronism commonly found in beating cilia. As a result, it is possible to pin point the type of fluid motion governing fluid mixing and fluid pumping. The developed computational model can, thus, successfully demonstrate filament-fluid interaction for a wide variety of similar problems. Originality/value: The present study uses a temporal second-order finite volume-based IBM to examine flexible filament dynamics for various applications such as fluid mixing. Also, it highlights the relationship between channel geometry ratio and filament aspect ratio and its effect on filament sweep patterns. The study further reports the effect of filament displacement dynamics with or without phase shift for inlet oscillating fluid flow condition. © 2019, Emerald Publishing Limited.Item Numerical and experimental investigation of modified V-shaped turbine blades for hydrokinetic energy generation(Elsevier Ltd, 2021) Shashikumar, S.; Madav, V.The Savonius rotor is one of the simple and cost-effective vertical axis drag type devices for hydropower generation. The main drawback of the Savonius hydrokinetic turbine is its low performance due to negative torque developed by returning blade profile. In this paper, the performance of modified V-shaped rotor blades with different V-angles ranging from 90° to 40°, by maintaining fixed edge length, arc radius and aspect ratio of 0.7 is investigated. The numerical analysis is carried out to estimate the optimum V-angle by maintaining 70 mm depth of water with an inlet velocity of 0.3090 m/s. The numerical study revealed that, for 80° V-angle rotor blade profile, the maximum coefficient of power was found to be 0.2279 at a tip speed ratio of 0.9. This optimum V-angle model was used for experimental analysis to study the effect of aspect ratio ranging from 0.7 to 1.75 using top, middle and bottom plates by maintaining 140 mm depth of water and inlet velocity of 0.513 m/s. The rotor blade with two endplates and one middle plate with an aspect ratio of 1.75 has shown a significant increase of performance by 86.13% at a tip speed ratio of 0.86 as compared to turbine blade with two endplates. © 2021 Elsevier LtdItem T-HISTORY ANALYSIS OF ASPECT RATIO EFFECT ON SUBCOOLING AND SOLIDIFICATION BEHAVIOUR OF PHASE CHANGE MATERIAL IN VERTICAL GLASS TUBES(Serbian Society of Heat Transfer Engineers, 2022) Rudra, M.B.V.; Gumtapure, V.The study deals with the effect of the tube aspect ratio on subcooling and the solidification behaviour of phase change material using the T-history method and is compared with the differential scanning calorimetry analysis. Three tubes of different aspect ratios, l/d, and a constant length of 178 mm are chosen for this study. Infrared contour depicts that the inner surface of the glass tube and phase change materia initiate heterogeneous nucleation. The differential scanning calorimetry heat flow graph indicates a higher degree of subcooling than T-history method. The study of aspect ratio with and without insulation shows that the mean value of degree of subcooling is less in the insulated tube than non-insulated tube due to reduced cooling rate. The effect of the high aspect ratio is to increase the degree of subcooling due to increased cooling rate and, however, decrease the sensible heat discharge time to reach the plateau, tplt. © 2022 Society of Thermal Engineers of Serbia. All Rights Reserved.Item Performance analysis of novel V-shaped turbine blade profile by three-dimensional numerical investigations with varying overlap ratios for hydropower application(Elsevier Ltd, 2022) Shashikumar, C.M.; Madav, V.In the present paper, three-dimensional numerical simulations were carried out to examine the influence of the overlap ratio between the two straight edges on the advancing and returning blades of the novel V-shaped rotor blade profiles using the sliding mesh technique. The performance parameters were computed with respect to the tip speed ratio. The findings show that the coefficient of torque and power for the novel V-shaped turbine blade is maximum for the zero-overlap ratio compared to the turbine blade, with an overlap ratio ranging from 0.05 to 0.3. The blade profiles' flow field was visualized at different angular positions, and various significant zones developed during the turbine blade rotation were captured and analyzed. The new overlapping jet developed between the two straight edges of the advancing and returning blade profiles as the overlap ratio varies from 0.05 to 0.3. Therefore, the turbine's performance is reduced due to the development of an overlap jet as it travels parallel to the straight edges of the blade profile and does not impact the rear side of the returning blade profile. © 2022 Elsevier LtdItem Buckling and free vibrations behaviour through differential quadrature method for foamed composites(Elsevier B.V., 2023) Duryodhana, D.; Waddar, S.; Bonthu, D.; Jeyaraj, P.; Powar, S.; Doddamani, M.The current work focuses on predicting the buckling and free vibration frequencies (fn) of cenosphere reinforced epoxy based syntactic foam beam under varying loads. Critical buckling loads (Ncr) and fn are predicted using the differential quadrature method (DQM). Ncr and fn have been calculated for beams of varying cenosphere volume fractions subjected to axial load under clamped-clamped (CC), clamped-simply (CS), simply-simply (SS), and clamped-free (CF) boundary conditions (BC′s). Upon increasing the cenosphere volume fraction, Ncr and fn of syntactic foam composites increases. These numerical outcomes are compared with the theoretical values evaluated through the Euler-Bernoulli hypothesis and further compared with experimental outcomes. Results are observed to be in precise agreement. The results of the DQM numerical analysis are given out for the different BC′s, aspect ratios, cenosphere volume fractions, and varying loads. It is perceived that depending on the BC′s, the type of axial varying loads and aspect ratios has a substantial effect on the Ncr and fn behaviour of the syntactic foam beams. A comparative study of the obtained results showed that the beam subjected to parabolic load under CC boundary conditions exhibited a higher buckling load. © 2023 The AuthorsItem Experimental investigation on flow boiling characteristics of the ethanol–water mixture in conventional channels(Springer Science and Business Media Deutschland GmbH, 2023) Krishnegowda, M.; Sathyabhama, S.The flow boiling heat transfer characteristics of the ethanol–water mixture (25%/75% by volume) and its pure constituents was experimentally investigated in conventional channels. The experiments were conducted for different ranges of mass flux, heat flux, subcooled inlet temperature and two different aspect ratios (AR). Flow patterns recorded by high-speed camera indicated that the bubble waiting and the growth period are minimum for the mixture and maximum for the ethanol, resulting in a higher heat transfer coefficient (HTC) for the mixture and lower HTC for ethanol in both the channels. For all the working fluids, high HTC was observed for the channel of AR = 1.25 in the forced convective region, whereas in the subcooled boiling region, high HTC was observed for the AR = 0.2 channel. The average subcooled HTC obtained for the 25% ethanol–water mixture was 15.75% and 38.85% higher than that of water and ethanol respectively for the AR = 0.2 channel. However, it was 18.11% and 41.2% higher than that of water and ethanol for the AR = 1.25 channel. © 2022, The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.Item Extensive analysis of PCM-based heat sink with different fin arrangements under varying load conditions and variable aspect ratio(Elsevier Ltd, 2023) Nedumaran, M.S.; Gnanasekaran, N.; Hooman, K.The present study compares a modified variable height fin heat sink with the conventional constant height fin heat sink. The two heat sinks are filled with an equal volume of PCM (n-eicosane) and a fin volume fraction of 8 %. The experiments are performed for constant loads and also different power surge conditions. The pulsed heat loads are applied for two scenarios: 1. Constant load 4 W - power surge and constant load 4 W - power surge - 1800 s no-load condition, and 2. Power surge (50 s, 100 s, and 150 s) - no-load conditions of 1800 s. During experiments, the proposed variable height fin heat sinks possess better thermal performance for all load scenarios. Further, a 3D computational model is developed using ANSYS Fluent 19 to assess not only the effect of fin arrangement for different aspect ratios but also the impact of fin shape. The enclosure aspect ratio employed for the given study ranges from 0.3 to 0.8 for both the heat sinks. Regarding the fin structure in a heat sink, four types of fin shapes are adopted: square, circular, diamond, and triangular. The contour images of temperature and the liquid fraction are shown for the charging process. For the discharging process, the time required for the heat sinks to completely solidify the PCM is discussed. From the outcomes, variable height fin heat sinks provide enhanced melting/solidification for all the aspect ratios and fin shapes considered. As the aspect ratio increases, the time difference between the heat sink for the completion of the discharging cycle is reduced. Moreover, the triangular shaped fin shows a higher enhancement percentage of 2.29 % and 1.43 % during melting and 6.25 % and 12.5 % during solidification for both the heat sinks, respectively. © 2023 The Author(s)Item Effect of RIBS/FINS and Aspect Ratio on Flow Boiling Characteristics in Conventional Channels(American Society of Mechanical Engineers (ASME), 2024) Madan, K.; Sathyabhama, A.In this work, experiments are conducted with conventional rectangular channels of two different aspect ratios (AR =w/d) for the horizontal boiling flow conditions at atmospheric pressure. Distilled water was used as the working substance. The heat transfer coefficients (HTC) were measured for mass fluxes and heat fluxes ranging from 85.94 kg/m2-s to 343.77 kg/m2-s and 10 kW/m2 to 100 kW/m2, respectively, and at inlet subcooled temperatures of 303 K, 313 K, and 323 K. Visualization of the boiling phenomenon was done using a high-speed camera for the two channels under similar conditions. The results show that the AR has a dominant effect on the HTC. At low heat flux values, higher HTC was noticed for the channel of higher AR (AR=1.25) whereas, at high heat flux conditions, the HTC is higher for the channel of lower AR (AR =0.2). With an increase in inlet subcooled temperature, the HTC decreased for both channels due to increased thermal boundary layer thickness and reduced bubble formation. Further, the channel of AR=1.25 with ribs/fins performed better than the smooth channel due to the high bubble nucleation rate. © 2023 by ASME.Item Local buckling strength enhancement due to non-slender flanges in web perforated plain channel columns(Elsevier Ltd, 2025) Francis, R.; Shabhari, A.; Jeyapragasam, V.V.K.; Chandrasekar, D.Cold-formed steel columns are the primary compression members in housing and industrial storage racks, with discrete holes or closely spaced web perforations. The element slenderness and web perforations influence the local buckling capacity. This study examines the local buckling capacity of slender web plain channel cross-sections with non-slender or slender flanges in the presence of web perforations. Fourteen plain channel stub column tests were conducted on two cross-section aspect ratios, two perforation shapes, with three perforation orientations. Further, a comprehensive parametric study was conducted using validated Finite Element models. The local buckling strength of unperforated and web-perforated cold-formed plain channel columns is evaluated using the Direct Strength Method (DSM) and Modified Direct Strength Method (MDSM). The increase in local buckling strength due to non-slender flanges becomes significant, depending on the aspect ratio and non-dimensional local buckling slenderness ratio of the plain channel cross-section. This research provides the scope to expand the applicability of DSM and MDSM design strength predictions from cold-formed steel design to general thin-walled steel sections, where the welded thin-walled steel sections can have different element thicknesses. As the element thickness plays a crucial role in element slenderness and inter-element interaction, the local buckling capacity prediction available for uniform cross-section thickness can be unduly conservative. This study highlights the significance of element slenderness and effective area reduction due to perforation shape and orientation in the local buckling strength of cold-formed plain channel sections. © 2025 Institution of Structural Engineers. Published by Elsevier Ltd. All rights are reserved, including those for text and data mining, AI training, and similar technologies.