Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
11 results
Search Results
Item Solar light induced photocatalytic degradation of Reactive Blue 220 (RB-220) dye with highly efficient Ag@TiO2 core-shell nanoparticles: A comparison with UV photocatalysis(2014) Khanna, A.; Shetty K, K.Ag core-TiO2 shell (Ag@TiO2) structured nanoparticles with Ag to TiO2 molar ratio of 1:1.7 were synthesized using one pot synthesis method and post calcination was carried out at 450°C for 3h to convert it from amorphous to crystalline form. The Ag core and TiO2 shell formation was confirmed by TEM and AFM. The particle size analysis revealed the average size of Ag@TiO2 as approximately around 30nm. EDS spectra showed the presence of O, Ag, and Ti elements. The improvement in optical properties was proved by DRS which showed significant red shift by Ag core in visible region. Ag@TiO2 exhibited better photocatalytic activity as compared to Degussa P25-TiO2, synthesized TiO2, and the Ag doped TiO2 photocatalysts under UV and solar light irradiation for degradation of Reactive Blue 220 (RB-220) dye. Higher rate of photocatalysis of RB-220 with Ag@TiO2 was obtained under solar light irradiation as compared to UV light irradiation, confirming the capability of the catalyst to absorb both UV and visible light. The kinetics of degradation of dye was found to follow modified Langmuir Hinshelwood (L-H) kinetic model. Ag@TiO2 can be recycled without much decline in the efficacy. Ag@TiO2 has been found to be the effective photocatalyst for degradation of water contaminated with azo dyes under both UV and solar light irradiations. © 2013 Elsevier Ltd.Item Optimizing the position of insulating materials in flat roofs exposed to sunshine to gain minimum heat into buildings under periodic heat transfer conditions(Springer Verlag service@springer.de, 2016) Saboor, S.; Ashok Babu, A.B.P.S.Building roofs are responsible for the huge heat gain in buildings. In the present work, an analysis of the influence of insulation location inside a flat roof exposed directly to the sun’s radiation was performed to reduce heat gain in buildings. The unsteady thermal response parameters of the building roof such as admittance, transmittance, decrement factor, and time lags have been investigated by solving a one-dimensional diffusion equation under convective periodic boundary conditions. Theoretical results of four types of walls were compared with the experimental results available in literature. The results reveal that the roof with insulation placed at the outer side and at the center plane of the roof is the most energy efficient from the lower decrement factor point of view and the roof with insulation placed at the center plane and the inner side of the roof is the best from the highest time lag point of view among the seven studied configurations. The composite roof with expanded polystyrene insulation located at the outer side and at the center plane of the roof is found to be the best roof from the lowest decrement factor (0.130) point of view, and the composite roof with resin-bonded mineral wool insulation located at the center plane and at the inner side of the roof is found to be energy efficient from the highest time lag point (9.33 h) of view among the seven configurations with five different insulation materials studied. The optimum fabric energy storage thicknesses of reinforced cement concrete, expanded polystyrene, foam glass, rock wool, rice husk, resin-bonded mineral wool, and cement plaster were computed. From the results, it is concluded that rock wool has the least optimum fabric energy storage thickness (0.114 m) among the seven studied building roof materials. © 2015, Springer-Verlag Berlin Heidelberg.Item Solar photocatalytically active, engineered silver nanoparticle synthesis using aqueous extract of mesocarp of Cocos nucifera (Red Spicata Dwarf)(Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2017) Sumi, M.B.; Devadiga, A.; Shetty K, V.K.; Saidutta, M.B.Silver nanoparticles synthesised using aqueous extract of Cocos nucifera (CN) mesocarp were evaluated for their photocatalytic activity under solar irradiation. The silver nanoparticles were synthesised by a green method of harnessing bioactive phytocomponents from the mesocarp of Cocos nucifera. Large-scale application of this process necessitates the manoeuvering of the process parameters for increasing the conversion of silver ions to nanoparticles. Process parameters influencing the morphological characteristics of silver nanoparticles such as precursor salt concentration and pH of the synthesis mixture were studied. The crystalline nanoparticles were characterised using UV-vis spectroscopy, XRD, FTIR, SEM and EDX analysis. CN extract and 5 mM silver nitrate solution at a ratio of 1:4 (v/v) in the synthesis mixture was found to be the optimum. Alkaline initial pH of the synthesis mixture was found to favour the synthesis of smaller sized monodispersed silver nanoparticles. Solar energy was harnessed for the photocatalytic degradation of Malachite green dye using silver nanoparticles obtained through the green synthesis method. Overall process aims at utilisation of naturally available resource for the synthesis of silver nanoparticles as well as the degradation of dyes using these nanoparticles, making it useful in the treatment of wastewater. © 2016 The Author(s). Published by Informa UK Limited, trading as Taylor & Francis Group.Item Photocatalytic water disinfection under solar irradiation by Ag@TiO2 core-shell structured nanoparticles(Elsevier Ltd, 2017) Sreeja, S.; Shetty K, V.K.The Ag core-TiO2 shell structured (Ag@TiO2) nanoparticles were found to be efficient in the disinfection of water under solar light irradiation both in free and immobilized form. Complete disinfection of 40 ? 108 CFU/mL Escherchia coli cells was achieved in 15 min by solar photocatalysis with 0.4 g/L Ag@TiO2 catalyst loading. Ag@TiO2 nanoparticles were found to be superior to TiO2 nanoparticles in solar disinfection. Photocatalysis rate was found to increase with increase in catalyst loading and with decrease in cell concentration. Ag@TiO2 nanoparticles showed their efficacy in the degradation of endotoxin, a harmful disinfection byproduct. Kinetics of solar disinfection with Ag@TiO2 nanoparticles followed Chick's law. The kinetics of endotoxin degradation followed zero order kinetics at high concentrations of endotoxin. However at lower concentrations, rate followed a nth order model with n = 6.99. A lower rate of photocatalytic disinfection with Ag@TiO2 nanoparticles immobilized on cellulose acetate as compared to that in their free form was observed, owing to diffusional and light penetration limitations. The re-growth of cells after photocatalytic disinfection was below the detectable limits, thus proving the potential of the process to produce safe drinking water. Ag@TiO2 nanoparticles can find potential application in solar water disinfection and the process which harnesses the solar energy may prove to be energy efficient and economical, thus can be easily adopted for large scale applications and portable drinking water treatment units for domestic applications. © 2017 Elsevier LtdItem Visible light-induced photocatalytic degradation of Reactive Blue-19 over highly efficient polyaniline-TiO2 nanocomposite: a comparative study with solar and UV photocatalysis(Springer Verlag service@springer.de, 2018) Kalikeri, S.; Kamath, N.; Gadgil, D.J.; Shetty K, V.Polyaniline-TiO2 (PANI-TiO2) nanocomposite was prepared by in situ polymerisation method. X-ray diffractogram (XRD) showed the formation of PANI-TiO2 nanocomposite with the average crystallite size of 46 nm containing anatase TiO2. The PANI-TiO2 nanocomposite consisted of short-chained fibrous structure of PANI with spherical TiO2 nanoparticles dispersed at the tips and edge of the fibres. The average hydrodynamic diameter of the nanocomposite was 99.5 nm. The band gap energy was 2.1 eV which showed its ability to absorb light in the visible range. The nanocomposite exhibited better visible light-mediated photocatalytic activity than TiO2 (Degussa P25) in terms of degradation of Reactive Blue (RB-19) dye. The photocatalysis was favoured under initial acidic pH, and complete degradation of 50 mg/L dye could be achieved at optimum catalyst loading of 1 g/L. The kinetics of degradation followed the Langmuir-Hinshelhood model. PANI-TiO2 nanocomposite showed almost similar photocatalytic activity under UV and visible light as well as in the solar light which comprises of radiation in both UV and visible light range. Chemical oxygen demand removal of 86% could also be achieved under visible light, confirming that simultaneous mineralization of the dye occurred during photocatalysis. PANI-TiO2 nanocomposites are promising photocatalysts for the treatment of industrial wastewater containing RB-19 dye. © 2017, Springer-Verlag GmbH Germany, part of Springer Nature.Item Solar light-driven photocatalysis using mixed-phase bismuth ferrite (BiFeO3/Bi25FeO40) nanoparticles for remediation of dye-contaminated water: kinetics and comparison with artificial UV and visible light-mediated photocatalysis(Springer Verlag service@springer.de, 2018) Kalikeri, S.; Shetty K, V.Mixed-phase bismuth ferrite (BFO) nanoparticles were prepared by co-precipitation method using potassium hydroxide as the precipitant. X-ray diffractogram (XRD) of the particles showed the formation of mixed-phase BFO nanoparticles containing BiFeO3/Bi25FeO40 phases with the crystallite size of 70 nm. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed the formation of quasi-spherical particles. The BFO nanoparticles were uniform sized with narrow size range and with the average hydrodynamic diameter of 76 nm. The band gap energy of 2.2 eV showed its ability to absorb light even in the visible range. Water contaminated with Acid Yellow (AY-17) and Reactive Blue (RB-19) dye was treated by photocatalysis under UV, visible, and solar light irradiation using the BFO nanoparticles. The BFO nanoparticles showed maximum photocatalytical activity under solar light as compared to UV and visible irradiations, and photocatalysis was favored under acidic pH. Complete degradation of AY-17 dyes and around 95% degradation of RB-19 could be achieved under solar light at pH 5. The kinetics of degradation followed the Langmuir–Hinshelhood kinetic model showing that the heterogeneous photocatalysis is adsorption controlled. The findings of this work prove the synthesized BFO nanoparticles as promising photocatalysts for the treatment of dye-contaminated industrial wastewater. © 2018, Springer-Verlag GmbH Germany, part of Springer Nature.Item Solar assisted photocatalytic degradation of organic pollutants in the presence of biogenic fluorescent ZnS nanocolloids(Elsevier Ltd, 2019) Uddandarao, P.; Hingnekar, T.A.; Mohan Balakrishnan, R.M.; Rene, E.R.The main aim of this study was to ascertain the photocatalytic degradation of organic pollutants present in aqueous phase using fluorescent biogenic ZnS nanocolloids produced from an endophytic fungus Aspergillus flavus. The degradation studies were carried out using different organic pollutants such as methyl violet (MV), 2,4-dichlorophenoxyacetic acid (2,4-D) and paracetamol (PARA) for 120 min, 270 min and 240 min, respectively, at pH varying from 3.0 to 11.0. The results from this study indicate that the degradation efficiency of ZnS nanocolloids for MV, 2,4-D and PARA were 87%, 33% and 51%, respectively, at the optimum concentration of 100 mg/L of the tested organic pollutants. At different time intervals, the samples were analyzed for their chemical oxygen demand (COD) and total organic carbon (TOC) contents. The reduction of COD and TOC were 78% and 74% for MV at 120 min; 55.5% and 57.2% for 2,4-D at 270 min and 47.6% and 44.5% for PARA at 240 min, respectively. The degradation pathway was determined based on the mass spectrum and the intermediates formed; in addition, the interaction between organic pollutants and nanocolloids was also elucidated based on atomic force microscopy (AFM) and fluorescence spectrum. © 2019 Elsevier LtdItem Auto-combustion synthesis of narrow band-gap bismuth ferrite nanoparticles for solar photocatalysis to remediate azo dye containing water(Springer Science and Business Media Deutschland GmbH, 2021) Kalikeri, S.; Shetty K, V.Narrow band gap of ferrites makes it a good photocatalyst, and it plays very prominent role in the level of degradation of organic dyes by photocatalysis. In the current study, bismuth ferrite (BFO) nanoparticles were synthesized by auto-combustion technique. The synthesized BFO particles have the average crystallite size of 33 nm and band gap energy of 1.9 eV. As revealed by microscopic images, uniform, distinct, and hexahedral shaped BFO nanoparticles of 42.7 nm are formed. The BFO nanoparticles exhibited visible and solar light-mediated photocatalytic activity in degrading Acid Yellow-17. The optimum pH and catalyst loading were found to be pH 5 and 0.2 g/L respectively. Around complete degradation under solar and 95% degradation under visible light could be achieved within 135 min of irradiation. Around 85% and 83% chemical oxygen demand (COD) removal could also be achieved under solar and visible light respectively. The degradation followed first-order kinetics in terms of COD removal. The BFO nanoparticles are promising as solar light active catalysts for wastewater treatment. © 2020, Springer-Verlag GmbH Germany, part of Springer Nature.Item Polymer-based immobilized Fe2O3–TiO2/PVP catalyst preparation method and the degradation of triclosan in treated greywater effluent by solar photocatalysis(Academic Press, 2021) Pragada, S.C.; Thalla, A.K.The present study involves a novel protocol to develop a ternary composite catalyst for an effective post-treatment technique for greywater. The ternary film of Fe2O3–TiO2/polyvinyl pyrrolidine (PVP) is coated on a glass tube using spray coating with annealing at 320 °C. The structure, thermal, microstructure, and surface properties of the coated film are characterized by X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Field Emission Scanning Electron Microscopy (FESEM), and Thermo Gravimetric Analysis (TGA). The scratch hardness of photocatalysts at different Fe2O3/TiO2 compositions is investigated based on the width measurement of scratch using FESEM analysis. Results show that at an optimum coating of 5% of Fe2O3/TiO2 composition catalytic film, the maximum scratch hardness (7.984 GPa) is obtained. Also, the photocatalyst has the highest cohesive bond strength and wearing resistance. The degradation of triclosan (TCS) in treated greywater, discharged from the anaerobic-aerobic treatment system, is investigated at a lab-scale using a solar photocatalytic reactor. The response surface analysis has been performed from the different sets of experimental trials for various optimal parameters. It is observed that the TCS degradation efficiency of 83.27% has resulted under optimum conditions. © 2021 Elsevier LtdItem Thermal performance assessment of a cylindrical box solar cooker fitted with decahedron outer reflector(SAGE Publications Inc., 2023) Anilkumar, B.C.; Maniyeri, R.; Anish, S.One of the important issues humankind globally faces in recent years is the scarcity of non-renewable energy resources. Solar energy is considered safe and renewable, which can fulfil the demand and supply chain requirements. Solar box cookers (SBCs) are popular in domestic cooking due to their ease of use and handling. The prime objective of the present work is to develop and test the performance of a cylindrical SBC fitted with decahedron-shaped reflector (CSBC-FDR). The CSBC is designed using minimum entropy generation (MEG) method. Through experiments, we observed that absorber plate attains peak temperature of about 138°C–150°C with the aid of decahedron reflector. The first figure of merit (F1) is found to be 0.13, indicating better optical efficiency and low heat loss coefficient for the SBC. The second figure of merit (F2) is obtained as 0.39, which indicates good heat exchange efficiency (F') and less heat capacity for cooker's interior. The average energy efficiency, exergy efficiency, and standardized cooking power values are 21.93%, 3.04%, and 25.28W, respectively. These results show that the present CSBC-FDR is able to cook food in a shorter period with better efficiency. The experimental and numerical values of overall heat loss coefficient of the developed SBC are in close agreement. The experimentally assessed performance parameters reveal superior performance of the present cylindrical SBC in comparison with many conventional rectangular and trapezoidal box solar cookers. © The Author(s) 2021.