Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
50 results
Search Results
Item Coconut coir pith, available in abundance especially in tropical countries, was studied as a substrate for the production of cellulase[1,4(1,3;1,4)???D?glucan 4?glucanohydrolase, EC 3.2.1.4] and ??D?glucosidase(??D?glucoside glucohydrolase, EC 3.2.1.21) in solid state fermentation. The effects of fermentation time, nutrient level, substrate particle size and inoculum size have been examined for optimal production of these enzymes by the fungal strain Aspergillus niger NCIM 1005. The highest filter paper activity (FPA) of 4.11 IU g?1, carboxyl methyl cellulose (CMCase) activity of 15·55 IU g?1 and cellobiase activity of 9·31 IU g?1 were obtained after 7 to 8 days of fermentation. Reese and Mandel's mineral solution in the substrate to mineral solution ratio of 1:10 (w/v) supported high cellulase and cellobiase activities. An inoculum size of 20–50% (v/v) based on the volume of mineral medium and substrate average particle size of 375 ?m were optimum for enzyme production. Copyright © 1994 SCI(Production of cellulases from coconut coir pith in solid state fermentation) Muniswaran, P.K.A.; Selvakumar, P.; Charyulu, N.C.L.N.1994Item Stimulus response experiments are conducted in four different rectangular columns having two and three spout cells. A pink-coloured polymer material is used as bed material with ambient air as the spouting fluid. A pulse input of dark blue colour polymer material is used as the stimulus, when the column is operating under steady flow conditions, and the response measured. A mathematical model 'plug flow-mixed flow in series' is used to fit the experimental data and the model parameters are evaluated.(Can Soc for Chem Eng, Mixing behaviour of solids in multiple spouted beds) Saidutta, M.B.; Murthy, D.V.R.2000Item Effect of media characteristics on performance of upflow aerobic biofilters(2008) Srinikethan, G.; Shrihari, S.; Pradeepan, V.S.Laboratory studies were conducted to assess the influence of media related factors such as porosity, pore size, particle size and specific surface area on the performance of upflow aerobic biofilters (ABFs). Three simple models of 8 litre capacity upflow submerged ABFs packed with support media of size 40 mm, 20 mm and 10 mm respectively were installed. The hydraulic retention time (HRT) was maintained as 12 hours. The study was carried out for a period of 90 days. The reactor performance indicated that the aerobic biofilter (ABF-3), associated with media of lowest porosity, pore size, particle size and highest specific surface area, demonstrating the highest BOD and COD removal efficiency of 93.32 % and 85.01 % respectively.Item Optimum size of granite filter media for the maximum treatment of domestic sewage in upflow anaerobic biofilters(2008) Srinikethan, G.; Shrihari, S.; Pradeepan, V.S.Laboratory studies were conducted to assess the influence of media related factors such as particle size, porosity, pore size and specific surface area on performance of upflow anaerobic biofilters (AnBFs). Three simple models of 8 litres capacity upflow anaerobic biofilters (AnBFs) packed with support media granite of size 40 mm, 20 mm and 10 mm respectively were installed. The experimental anaerobic biofilters (AnBFs) were made of PVC tubes. The hydraulic retention time (HRT) was maintained as 12 hours. The study was carried out for a period of 90 days. The waste treatment performance indicates that the anaerobic biofilter (AnBF-2) packed with granite media of moderate particle size of 20mm demonstrated the highest BOD and COD removal 91.02 % and 82.01 % respectively. Copyright © Enviromedia.Item Phase transformation, structural evolution and mechanical property of nanostructured FeAl as a result of mechanical alloying(2009) Rajath Hegde, M.M.R.; Surendranathan, A.O.Objective of the work was to synthesize nanostructured FeAl alloy powder by mechanical alloying (MEA). The work concentrated on synthesis, characterization, structural and mechanical properties of the alloy. Nanostructured FeAl intermetallics were prepared directly by MEA in a high energy rate ball mill. Milling was performed under toluene solution to avoid contamination from the milling media and atmosphere. Mixtures of elemental Fe and Al were progressively transformed into a partially disordered solid solution with an average composition of Fe-50 at % Al. Phase transformation, structural changes, morphology, particle size measurement and chemical composition during MEA were investigated by X-ray diffraction (XRD), Scanning electron microscopy (SEM) and Energy dispersive X-ray spectroscopy (EDS) respectively. Vickers micro hardness (VMH) indentation tests were performed on the powders. XRD and SEM studies revealed the alloying of elemental powders as well as transition to nanostructured alloy, crystallite size of 18 nm was obtained after 28 hours of milling. Expansion/contraction in lattice parameter accompanied by reduction in crystallite size occurs during transition to nanostructured alloy. Longer milling duration introduces ordering in the alloyed powders as proved by the presence of superlattice reflection. Elemental and alloyed phase coexist while hardness increased during MEA. © 2009 Allerton Press, Inc.Item Particle deposition in human respiratory system: Deposition of concentrated hygroscopic aerosols(2009) Varghese, S.K.; Gangamma, S.In the nearly saturated human respiratory tract, the presence of water-soluble substances in the inhaled aerosols can cause change in the size distribution of the particles. This consequently alters the lung deposition profiles of the inhaled airborne particles. Similarly, the presence of high concentration of hygroscopic aerosols also affects the water vapor and temperature profiles in the respiratory tract. A model is presented to analyze these effects in human respiratory system. The model solves simultaneously the heat and mass transfer equations to determine the size evolution of respirable particles and gas-phase properties within human respiratory tract. First, the model predictions for nonhygroscopic aerosols are compared with experimental results. The model results are compared with experimental results of sodium chloride particles. The model reproduces the major features of the experimental data. The water vapor profile is significantly modified only when a high concentration of particles is present. The model is used to study the effect of equilibrium assumptions on particle deposition. Simulations show that an infinite dilution solution assumption to calculate the saturation equilibrium over droplet could induce errors in estimating particle growth. This error is significant in the case of particles of size greater than 1 ?m and at number concentrations higher than 105/cm3. © 2009 Informa UK Ltd.Item Synthesis and characterization of temperature sensitive P-NIPAM macro/micro hydrogels(Elsevier B.V., 2011) JagadeeshBabu, P.E.; Suresh Kumar, R.; Maheswari, B.A thermo responsive macro porous poly(N-isopropylacrylamide) hydrogel was synthesized using free radical polymerization. The reaction was optimized by varying the reaction temperature, monomer, cross-linker and initiator based on the strength and swelling characteristics of the hydrogel. The morphology of the macro hydrogel was observed using scanning electron microscope (SEM). The swelling behavior of the macro hydrogel was performed gravimetrically and found that the gel synthesized at 36 °C had maximum deswelling ratio of 34.5 (-). These optimized values were further used to synthesis micro hydrogels using water-oil (w/o) emulsion technique. The morphology of the micro hydrogels were observed through SEM. Effect of water-oil ratio and stirrer speed on the mean particle size of the micro hydrogels were studied. Micro hydrogels synthesized at 1:1.5. w/o ratio and at 800. rpm had perfect spherical shape and had least particle mean diameter of 0.74 ?m, with SD of 0.5. Dye release kinetics with respect to temperature and time were studied using methylene blue solution. The release kinetic studies of micro hydrogel showed higher sustained release for 56. h compared to the macro hydrogel. © 2011 Elsevier B.V.Item Stability of horizontal oil well - A Jointed Rock model approach(2011) Anantharamu, A.; Singh, T.N.; Venkat Reddy, D.Advancement in technology has paved different ways for the extraction of oil. Drilling of wells, production and injection of fluids results in the alteration of pre-existing stress field in a reservoir. The current study is undertaken to analyze the stability of horizontal oil wells with the change in radius of the well, Poisson's ratio, saturation density, permeability and also to find stress distribution around horizontal oil wells drilled in different reservoir conditions, stress distribution before and after production and also to assess the effect of stress distribution on the stability. The knowledge of stress distribution and its redistribution with change in reservoir conditions can help in selecting well locations and orientations for maximum sweep in reservoirs. Displacement of the particles gives the direction of fracture propagation. As the particle size increases, fracture propagation increases. The stability analysis has been done using Jointed Rock method of Numerical Modeling. Numerical models are mathematical models that use numerical time-stepping procedure to obtain the models behavior over time. The results of the model are shown to agree qualitatively with field observations. The extent of stress distribution is dependent on radius of the well, pore pressure in the reservoir, fracture density of the reservoir and drilling direction. Horizontal wells drilled in highly fractured reservoirs will be less stable. In case of anisotropy, since the stability is very less we must reduce the radius of the well in order to increase the FOS and hence the stability. © 2011 CAFET-INNOVA TECHNICAL SOCIETY.Item