Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
14 results
Search Results
Item Synthesis, characterization and desalination study of composite NF membranes of novel Poly[(4-aminophenyl)sulfonyl]butanediamide (PASB) and methyalated Poly[(4-aminophenyl)sulfonyl]butanediamide (mPASB) with Polysulfone (PSf)(2013) Padaki, M.; Isloor, A.M.; Kumar, R.; A.F., A.F.; Matsuura, T.In the present investigation, Poly [(4-aminophenyl)sulfonyl]butanediamide (PASB) and methylated Poly[(4-aminophenyl)sulfonyl] butanediamide (mPASB) polymers were synthesized, using succinyl chloride and substituted 4-amino-1-benzenesulphonamide. Polysulfone composite membranes were prepared by blending these novel polymers by Diffusion Induced Phase Separation (DIPS) method. The performance of the membrane was studied in terms of salt rejection, water flux and molecular weight cutoff. The prepared membranes were hydrophilic in nature, which was confirmed by water uptake studies and contact angle measurement. All the membranes showed 1000. Da molecular weight cutoff. A maximum NaCl rejection of 52% was observed in some of the membranes. The effect of feed NaCl concentration on the NaCl rejection was also studied. The resistance of the membranes in a wide pH range was studied by water uptake measurement. Antifouling properties of the membranes were also performed using Bovine Serum Albumin (BSA) solution. © 2012 Elsevier B.V.Item Synthesis and characterization of novel water soluble derivative of Chitosan as an additive for polysulfone ultrafiltration membrane(2013) Kumar, R.; Isloor, A.M.; A.F., A.F.; Matsuura, T.A novel water soluble Chitosan derivative N-propylphosphonic Chitosan (NPPCS) having a terminal phosphonic acid group was synthesized by reacting Chitosan with Hydroxybenzotriazole (HOBt) and propylphosphonic anhydride (T3P)® via one pot reaction. The novel derivative was characterized by 1H NMR, Attenuated Total Reflectance Infra Red (ATR-IR) spectroscopy and XRD. Due to insolubility of NPPCS in organic solvents, a new process was demonstrated for blending of NPPCS with Polysulfone. The proper blending of NPPCS with Polysulfone was confirmed by ATR-IR spectroscopy. The improved hydrophilicity of PSf/NPPCS membranes was confirmed by contact angle measurement. The permeation studies showed increased flux of PSf/NPPCS membranes as compared to the pristine Polysulfone membrane. The antifouling property of PSf/NPPCS membrane was determined by Bovine Serum Albumin (BSA) protein rejection studies. The membranes showed the enhanced antifouling property as compared to pristine Polysulfone membranes with a maximum of 74% flux recovery ratio (FRR) value. © 2013 Elsevier B.V.Item Role of N-vinyl-2-pyrrolidinone on the thermoresponsive behavior of PNIPAm hydrogel and its release kinetics using dye and vitamin-B12 as model drug(2014) Maheswari, B.; JagadeeshBabu, P.E.; Agarwal, M.Temperature-sensitive hydrogels hold great promise in biological applications as they can respond to changes in physiological temperature to produce a desired effect like controlled drug delivery. In this study, a series of poly(N-isopropylacrylamide-co-N-vinyl-2-pyrrolidinone) thermosensitive hydrogels were synthesized by radical copolymerization of NIPAm with 1-vinyl-2-pyrrolidinone (NVP). By altering the initial NIPAm/NVP mole ratios, copolymers were synthesized to have their own distinctive lower critical solution temperature which was established using differential scanning calorimetry. The swelling behavior of the hydrogel was analyzed gravimetrically and it was observed that reswelling rate increases with increasing NVP mole ratio. Further characterizations of the hydrogels were performed using Fourier transform infrared spectroscopy and scanning electron microscopy. Release kinetics with respect to temperature was studied using methylene blue dye solution and vitamin B12. Kinetic modeling of the release profile revealed that the release mechanism is a non-Fickian diffusion mechanism. These results suggested that this material has potential application as intelligent drug carriers. The quantities of residual monomers in the PIV4 hydrogel were determined by HPLC method, and the results show almost complete conversion. © 2013 Taylor & Francis.Item Preparation, characterization and the effect of PANI coated TiO2 nanocomposites on the performance of polysulfone ultrafiltration membranes(Royal Society of Chemistry, 2015) Pereira, V.R.; Isloor, A.M.; Ahmed, A.A.; A.F., A.F.Polysulfone ultrafiltration (UF) membranes with PANI-TiO2 (polyaniline-titania) nanocomposites and PEG 1000 (Polyethylene Glycol 1000) as additives were prepared by the phase inversion method. PANI-TiO2 nanocomposites were synthesized by coating TiO2 nanotubes with PANI via chemical oxidative polymerization. The synthesized PANI-TiO2 nanocomposite was characterized by Fourier Transform Infrared Spectroscopy (FTIR), X-ray diffraction (XRD) and Transmission Electron Microscope (TEM) analysis. PANI-TiO2 nanocomposites with varying concentrations (0-1.5 wt%) were dispersed in the polysulfone membrane matrix with N-methyl-2-pyrrolidone (NMP) as solvent along with PEG 1000 as the pore former. The effect of addition of PANI-TiO2 nanocomposites with different concentrations (0-1.5 wt%) on the membrane structure, performance, hydrophilicity and the antifouling nature of the membranes was analyzed. PANI-TiO2 nanocomposite membranes showed better hydrophilicity, improved permeability, enhanced porosity, water uptake and good antifouling ability when compared with neat polysulfone membranes. The performance of the membranes improved with the increase in the addition of the PANI-TiO2 nanocomposite. However, the membrane performance decreased slightly at 1.5 wt% addition of PANI-TiO2 due to the agglomeration of PANI-TiO2 at higher concentration. The well performed membranes were also subjected to heavy metal ion rejection. The membranes showed a rejection of 83.75% and 73.41% during the polymer enhanced ultrafiltration (PEUF) process and a rejection of 68% and 53.78% during the UF process for Pb2+ and Cd2+ respectively. © The Royal Society of Chemistry and the Centre National de la Recherche Scientifique 2015.Item Probing the morphology and anti-organic fouling behaviour of a polyetherimide membrane modified with hydrophilic organic acids as additives(Royal Society of Chemistry, 2015) Hebbar, R.S.; Isloor, A.M.; A.F., A.F.; Shilton, S.J.; AlObaid, A.; Fun, H.-K.A facile approach for the preparation of an organic antifouling polymer membrane has been developed using low molecular weight organic acids as additives. The presence of these additives in the membrane was analysed by FTIR spectroscopy. The properties of the modified membranes were investigated in terms of contact angle, water uptake capacity, SEM and AFM analysis. These additives exerted a strong impact on the rheological properties of the casting solution, thereby altering the membrane morphology, surface roughness, water flux and the hydrophilicity of the membranes, as compared to those of the pristine polyetherimide (PEI) membrane. The organic antifouling properties of the modified membrane were analysed by filtering both bovine serum albumin (BSA) and humic acid solutions. The results showed that the additives exhibited a remarkable improvement in the antifouling properties (FRR of 72%) and a humic acid rejection of up to 86%. These outcomes offer new insights into the use of cheaper and readily available organic acids as additives, compared to the traditional, synthetic polymer materials as additives in membrane preparation. ©2015 The Royal Society of Chemistry and the Centre National de la Recherche Scientifique.Item Favorable influence of mPIAM on PSf blend membranes for ion rejection(Elsevier B.V., 2017) Jyothi, M.S.; Soontarapa, K.; Padaki, M.; Balakrishna, R.G.; Isloor, A.M.The study reports the use of a novel membrane for heavy metal removal and salt rejection. Poly isobutylene alt maleic anhydride (PIAM) modified by sulfanilic acid is blended with polysulfone (PSf) in different concentrations. This induces surface charge and hydrophillicity in the otherwise hydrophobic PSf membranes. The so modified polymers and their blends are characterized by spectroscopic and microscopic techniques. Blend membranes show drastically enhanced performance with respect to water flux, water uptake and ion exchange capacity. SEM micrographs indicate the hydrophilic domains, –SO3H groups in the polymer to have formed cavities during phase inversion process, thus enhancing permeability. 100% rejection of PEG 2000 and 59% of NaCl rejection substantiated the nature of the membrane to be nanofiltration (NF) type. The prepared membranes were further evaluated for Cr (VI) removal, with removal efficiency reaching above 92%. The electronic coupling that occurs between SO3H? and Na+ and the electrostatic interaction between metal ions and the charge on membrane facilitates NaCl and Cr (VI) rejection respectively. The study gains significance in use of such modified PIAM as blend material with any other polymer to enhance the native properties of the blend membrane. © 2017 Elsevier B.V.Item Fabrication of a novel hollow fiber membrane decorated with functionalized Fe2O3 nanoparticles: Towards sustainable water treatment and biofouling control(Royal Society of Chemistry, 2017) Hebbar, R.S.; Isloor, A.M.; Kulal, K.; Abdullah, M.S.; A.F., A.F.The development of sustainable, surface-functionalized hollow fiber membranes with advanced nanomaterials has enabled the tailoring and targeted control of their physicochemical properties. This provides the material with improved features of hydrophilicity and permeability, excellent selectivity, and superior antifouling and antimicrobial activity. We explored a new strategy using well dispersed functionalized Fe2O3 nanoparticles to fabricate a polyetherimide nanocomposite hollow fiber membrane with enhanced surface and anti-biofouling properties. To confirm the membrane modification, a series of characterizations such as contact angle, surface energy, water uptake capacity, porosity, zeta potential, and morphological analysis were performed. The permeation experiment indicated superior hydrodynamic permeability and antifouling properties with more than 95% rejection of BSA protein molecules after inclusion of a 1.5 wt% additive dosage. Moreover, the nanocomposite membrane exhibited a relatively higher normalized flux and rejection up to 94% during the filtration of hazardous natural organic matter (NOM) with differing parameters such as the feed solution pH and ionic strength. The presence of modified Fe2O3 nanoparticles in the membrane significantly inhibits the growth of bacteria and other microorganisms on the membrane surface, resulting in an enhanced anti-biofouling property. In particular, the demonstrated method illustrates a fast, facile strategy for the functionalization of Fe2O3 nanoparticles to improve the membrane properties and anti-biofouling activity, giving them great potential for effective and sustainable water treatment applications. © 2017 The Royal Society of Chemistry and the Centre National de la Recherche Scientifique.Item Improvement in performance of polysulfone membranes through the incorporation of chitosan-(3-phenyl-1h-pyrazole-4-carbaldehyde)(Cogent OA info@CogentOA.com, 2017) Balakrishna Prabhu, K.; Saidutta, M.B.; Isloor, A.M.; Hebbar, R.S.Pure polysulfone membranes are known to exhibit poor permeability, and high fouling. This study was conducted to explore the possibility of improving the permeation characteristics of polysulfone membranes by using a chitosan derivative as an additive. Polysulfone membranes blended with chitosan derivative 3-phenyl-1H-pyrazole-4-carbaldehyde (ChD) were prepared by the method of wet coagulation. The hydroxyl, amine and the imine functional groups present in the ChD evidently increased the hydrophilicity of the surface of the blended membranes which was confirmed by contact angle measurements. The contact angle of the blended membrane having 2 wt.% ChD was 62 ± 1 as compared to 70 ± 1 of neat polysulfone membrane. The SEM analysis of the blended membranes revealed a highly porous structure with a very thin surface skin layer, finger like projections in the sub-layer with a macro void structure at the base. The blended membranes also showed significant improvement in pure water flux of 351 L m?2 h?1 at 0.8 MPa trans membrane pressure (TMP) as compared to 24 L m?2 h?1 of neat polysulfone membrane at the same TMP. The anti-fouling test using bovine serum albumin exhibited improved anti-fouling characteristic of blended membranes with a maximum flux recovery ratio (FRR) of 57%. The heavy metal rejection study revealed that membrane P-1 showed maximum 36 and 29% rejection for Pb and Cu respectively. © 2017 The Author(s). This open access article is distributed under a Creative Commons Attribution (CC-BY) 4.0 license.Item Use of cellulose acetate/polyphenylsulfone derivatives to fabricate ultrafiltration hollow fiber membranes for the removal of arsenic from drinking water(Elsevier B.V., 2019) Kumar, M.; Todeti, S.; Isloor, A.M.; Gnani Peer Mohamed, G.P.S.; Siddique, I.; Ismail, N.I.; A.F., A.F.; Asiri, A.M.Cellulose acetate (CA) and cellulose acetate phthalate (CAP) were used as additives (1 wt%, 3 wt%, and 5 wt%) to prepare polyphenylsulfone (PPSU) hollow fiber membranes. Prepared hollow fiber membranes were characterized by surface morphology using scanning electron microscopy (SEM), surface roughness by atomic force microscopy (AFM), the surface charge of the membrane was analyzed by zeta potential measurement, hydrophilicity by contact angle measurement and the functional groups by fourier transform infrared spectroscopy (FTIR). Fouling resistant nature of the prepared hollow fiber membranes was evaluated by bovine serum albumin (BSA) and molecular weight cutoff was investigated using polyethylene glycol (PEG). By total organic carbon (TOC), the percentage rejection of PEG was found to be 14,489 Da. It was found that the hollow fiber membrane prepared by the addition of 5 wt% of CAP in PPSU confirmed increased arsenic removal from water as compared to hollow fiber membrane prepared by 5 wt% of CA in PPSU. The removal percentages of arsenic with CA-5 and CAP-5 hollow fiber membrane was 34% and 41% with arsenic removal permeability was 44.42 L/m2h bar and 40.11 L/m2h bar respectively. The increased pure water permeability for CA-5 and CAP-5 hollow fiber membrane was 61.47 L/m2h bar and 69.60 L/m2 h bar, respectively. © 2019 Elsevier B.V.Item Degradation, wettability and surface characteristics of laser surface modified Mg–Zn–Gd–Nd alloy(Springer, 2020) K.r, R.; Bontha, S.; M.r, R.; Das, M.; Balla, V.K.This work evaluates the effects of laser surface modification on Mg–Zn–Gd–Nd alloy which is a potential biodegradable material for temporary bone implant applications. The laser surface melted (LSM) samples were investigated for microstructure, wettability, surface hardness and in vitro degradation. The microstructural study was carried out using scanning and transmission electron microscopes (SEM, TEM) and the phases present were analyzed using X-ray diffraction. The in vitro degradation behaviour was assessed in hank’s balanced salt solution (HBSS) by immersion corrosion technique and the effect of LSM process parameters on the wettability was analyzed through contact angle measurements. The microstructural examination showed remarkable grain refinement as well as uniform redistribution of intermetallic phases throughout the matrix after LSM. These microstructural changes increased the hardness of LSM samples with an increase in energy density. The wetting behaviour of processed samples showed hydrophilic nature when processed at lower (12.5 and 17.5 J/mm2) and intermediate energy density (22.5 and 25 J/mm2), which can potentially improve cell-materials interaction. The corrosion rate of as cast Mg–Zn–Gd–Nd alloy decreased by ~83% due to LSM. [Figure not available: see fulltext.]. © 2020, Springer Science+Business Media, LLC, part of Springer Nature.