Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
14 results
Search Results
Item Novel one-pot green synthesis of graphene in aqueous medium under microwave irradiation using a regenerative catalyst and the study of its electrochemical properties(Royal Society of Chemistry, 2015) Subramanya, B.; Bhat, D.In this work we report an economic, eco-friendly, high yielding and facile one-pot method for the large scale synthesis of few layer graphene (FLG) nanosheets directly from graphite in aqueous medium using a regenerative catalyst, sodium tungstate. This method is fast and makes use of environmental friendly chemicals and microwave radiation. The as-synthesized FLG nanosheets are characterized by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) surface area analysis. Raman analysis indicates that the as-synthesized graphene is bilayered with a smaller domain size of 3.9 nm which is responsible for a higher specific surface area of FLG nanosheets (1103.62 m2 g-1). Moreover, XPS analysis of FLG nanosheets shows a high C:O ratio (?9.6) which is the best among the graphene prepared from green chemicals. The electrochemical performance of as-synthesized FLG nanosheets is analysed by cyclic voltammetry (CV), chronopotentiometry and electrochemical impedance spectroscopy (EIS) in neat 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIMBF4) electrolyte. The superior capacitive performance with large capacitance (219 F g-1), high energy density (83.56 W h kg-1) and excellent cyclability (3000 cycles) exhibited by these graphene nanosheets make them an excellent candidate for supercapacitor material. © The Royal Society of Chemistry and the Centre National de la Recherche Scientifique 2015.Item Energy storage and management in supercapacitors for application in piezoelectric energy harvesting systems(Sphinx Knowledge House info@sphinxsai.com, 2015) Sripad, S.; Kumar, S.; Jain, A.Electrical double layer capacitors (supercapacitors) were fabricated using activated carbon as the active material and polyvinylidine fluoride (PVDF) as a binder with a suitable conductive additive (MWCNTs) together in an optimized ratio. The supercapacitor cells were assembled using an aqueous solution of 0.5M Na2SO4 as the electrolyte. These cells had an average capacitance of 1.7F each as measured by the constant current charging method. The two electrode symmetric cell had a specific capacitance of 23.05 F/g. The fabrication methodology has been discussed as well as the potential applications of the supercapacitor in piezoelectric element based energy harvesting systems have been elucidated. © 2015, International Journal of ChemTech Research. All rights reserved.Item Effects of electric potential, NaCl, pH and distance between electrodes on efficiency of electrolysis in landfill leachate treatment(Taylor and Francis Inc. 325 Chestnut St, Suite 800 Philadelphia PA 19106, 2017) Erabee, I.K.; Ahsan, A.; Jose, B.; Arunkumar, T.; Sathyamurthy, R.; Idrus, S.; Daud, N.N.N.This study investigated the effects of different parameters on the removal efficiencies of organic and inorganic pollutants in landfill leachate treatment by electrolysis. Different parameters were considered such as the electric potential (e.g., 24, 40 and 60 V), hydraulic retention time (HRT) (e.g., 40, 60, 80, 100 and 120 min), sodium chloride (NaCl) concentration (e.g., 1, 3, 5 and 7%), pH (e.g., 3, 7 and 9), electrodes materials [e.g., aluminum (Al) and iron (Fe)] and distance between electrodes (e.g., 1, 2 and 3 cm). The best operational condition of electrolysis was then recommended. The electric potential of 60 V with HRT of 120 min at 5% of NaCl solution using Al as anode and Fe as cathode (kept at a distance of 3 cm) was the most efficient condition which increased the removal efficiencies of various parameters such as turbidity, salinity, total suspended solids (TSS), total dissolved solids (TDS), biochemical oxygen demand (BOD), chemical oxygen demand (COD) and heavy metals (e.g., Zn and Mn). The higher removal percentages of many parameters, especially COD (94%) and Mn (93%) indicated that the electrolysis is an efficient technique for multi-pollutants (e.g., organic, inorganic and heavy metals) removal from the landfill leachate. © 2017 Taylor & Francis Group, LLC.Item Enhancing photovoltaic performance of DSSCs sensitized with Ru-II complexes by D-?-A configured carbazole based co-sensitizers(Royal Society of Chemistry, 2018) Naik, P.; Elmorsy, M.R.; Su, R.; El-Shafei, A.; Vasudeva Adhikari, A.Herein, we report the photovoltaic performance studies of four D-?-A configured carbazole based co-sensitizers, P1-4, in DSSCs sensitized with Ru-II complexes, i.e.NCSU-10/N3. The organic co-sensitizers (P1-4) comprise carbazole as a donor scaffold, a phenylene ring as a ?-spacer and electron withdrawing functional groups, viz. cyanoacetic acid (P1), rhodanine-3-acetic acid (P1-2), barbituric acid (P3), and thiobarbituric acid (P4) as acceptor/anchoring units. From the results, it is evident that the device fabricated using co-sensitizer P1 carrying cyanoacetic acid, at the concentration of 0.2 mM NCSU-10, exhibited an enhanced photon conversion efficiency (PCE) of 9.19% with a JSC of 21.20 mA cm-2, VOC of 0.658 V and FF of 65.85%, while P3 containing barbituric acid displayed a PCE of 8.75% with a JSC of 22.23 mA cm-2, VOC of 0.671 V and FF of 58.64%, whereas NCSU-10 (0.2 mM) alone displayed a PCE of 8.28% with a JSC of 20.38 mA cm-2, VOC of 0.665 V and FF of 61.09%, but the dyes P2 carrying rhodanine-3-acetic acid and P4 containing thiobarbituric acid showed considerably lower performance. The co-sensitized devices of N3 with P1-4 displayed inferior photovoltaic performance compared to N3 itself, probably due to inefficient suppression of back current. The observed results have thrown new light upon the selection of appropriate and matchable co-sensitizers for improving photovoltaic performance of Ru-II based sensitizers. © 2018 The Royal Society of Chemistry and the Centre National de la Recherche Scientifique.Item An Integrated Approach of CNT Front-end Amplifier towards Spikes Monitoring for Neuro-prosthetic Diagnosis(SpringerOpen, 2018) Kumar, S.; Kim, B.-S.; Song, H.The future neuro-prosthetic devices would be required spikes data monitoring through sub-nanoscale transistors that enables to neuroscientists and clinicals for scalable, wireless and implantable applications. This research investigates the spikes monitoring through integrated CNT front-end amplifier for neuro-prosthetic diagnosis. The proposed carbon nanotube-based architecture consists of front-end amplifier (FEA), integrate fire neuron and pseudo resistor technique that observed high electrical performance through neural activity. A pseudo resistor technique ensures large input impedance for integrated FEA by compensating the input leakage current. While carbon nanotube based FEA provides low-voltage operation with directly impacts on the power consumption and also give detector size that demonstrates fidelity of the neural signals. The observed neural activity shows amplitude of spiking in terms of action potential up to 80 ?V while local field potentials up to 40 mV by using proposed architecture. This fully integrated architecture is implemented in Analog cadence virtuoso using design kit of CNT process. The fabricated chip consumes less power consumption of 2 ?W under the supply voltage of 0.7 V. The experimental and simulated results of the integrated FEA achieves 60 G? of input impedance and input referred noise of 8.5 nv/Hzover the wide bandwidth. Moreover, measured gain of the amplifier achieves 75 dB midband from range of 1 KHz to 35 KHz. The proposed research provides refreshing neural recording data through nanotube integrated circuit and which could be beneficial for the next generation neuroscientists. © 2018, The Korean BioChip Society and Springer-Verlag GmbH Germany, part of Springer Nature.Item High-Performance Graphene FET Integrated Front-End Amplifier Using Pseudo-resistor Technique for Neuro-prosthetic Diagnosis(SpringerOpen, 2022) Naik, J.D.; Gorre, P.; Akuri, N.G.; Kumar, S.; Al-Shidaifat, A.D.; Song, H.A complex analysis of spike monitoring in neuro-prosthetic diagnosis demands a high-speed sub-nanoscale transistors with an advanced device technologies. This work reports the high performance of Graphene field-effect transistor (GFET) based front-end amplifier (FEA) design for the neuro-prosthetic application. The 9 nm Graphene FET device is optimized by characterization of transconductance and drain current towards high sensitivity and small factor. The proposed GFET-based FEA with pseudo-resistor technique demonstrates very high-input impedance in Tera-ohms that nullify the input leakage current. Here, gain-bandwidth product and noise optimization of GFET FEA enhances the overall gain with negligible noise. The proposed design operates at low voltage, further reduces the power consumption, and achieves less chip area in sub-nano size so it could be more suitable for implantable devices. The GFET-based FEA architecture achieves an action potential spike of 1.4 µV while the local field potentials spike of 1.8 mV. The proposed architecture is implemented in Advanced Design System using the design kit of the GFET process. Power consumption of 3.14 µW is observed with a supply voltage of 0.9 V. The simulated and experimental results of the proposed design achieve an input impedance of 2 TΩ with excellent noise performance over a wideband of 13.85 MHz. The proposed work demonstrates better neural activity sensing when compared to the state-of-the-artwork, which could be highly beneficial for future neuroscientists. © 2022, The Korean BioChip Society.Item Smart distribution network voltage estimation using PMU technology considering zero injection constraints(Public Library of Science, 2024) Tangi, S.; Gaonkar, D.N.; Nuvvula, R.S.S.; P Kumar, P.P.; Çolak, I.; Tazay, A.F.; Mosaad, M.I.To properly control the network of the power system and ensure its protection, Phasor measurement units (PMUs) must be used to monitor the network's operation. PMUs can provide synchronized real-time measurements. These measurements can be used for state estimation, fault detection and diagnosis, and other grid control applications. Conventional state estimation methods use weighting factors to balance the different types of measurements, and zero injection measurements can lead to large weighting factors that can introduce computational errors. The offered methods are designed to ensure that these zero injection criteria can be strictly satisfied while calculating the voltage profile and observability of the various distribution networks without sacrificing computing efficiency. The proposed method's viability is assessed using standard IEEE distribution networks. MATLAB coding is used to simulate the case analyses. Overall, the study provides a valuable contribution to the field of power distribution system monitoring and control by simplifying the process of determining the optimal locations for PMUs in a distribution network and assessing the impact of ZI buses on the voltage profile of the system. ©: © 2024 Tangi et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.Item Molecular surface-dependent light harvesting and photo charge separation in plant-derived carbon quantum dots for visible-light-driven OH radical generation for remediation of aromatic hydrocarbon pollutants and real wastewater(Academic Press Inc., 2024) Meena, S.; Sethi, M.; Saini, S.; Kumar, K.; Saini, P.; Meena, S.; Kashyap, S.; Yadav, M.; Meena, M.L.; Dandia, A.; Nirmal, N.K.; Parewa, V.Despite the growing emphasis on eco-friendly nanomaterials as energy harvesters, scientists are actively searching for metal-free photocatalysts to be used in environmental remediation strategies. Developing renewable resource-based carbon quantum dots (CQDs) as the sole photocatalyst to harvest visible light for efficient pollutant degradation is crucial yet challenging, particularly for addressing the escalating issue of water deterioration. Moreover, the photocatalytic decomposition of H2O2 under visible light irradiation remains an arduous task. Based on this, we designed two types of CQDs, C-CQDs (carboxylic-rich) and A-CQDs (amine-rich) with distinct molecular surfaces. Owing to the higher amount of upward band bending induced by amine-rich molecular surface, A-CQDs efficiently harvest the visible light and prevent recombination kinetics resulting in prolonged lifetimes (25 ps), and augmented charge carrier density (35.7 × 1018) of photoexcited charge carriers. A-CQDs enabled rapid visible-light-driven photolysis of H2O2 (k = 0.058 min−1) and produced higher quantity of •OH radicals (0.158 μmol/sec) for the mineralization of petroleum waste, BETX (i.e. Benzene, Ethylbenzene, Toluene and Xylene) (k = 0.017–0.026 min−1) and real textile wastewater (k = 0.026 min−1). To assess comparative toxicities of both remediated and non-remediated real wastewater samples in a time and dose depended manner, Drosophila melanogaster was used as a model organism. The findings unequivocally demonstrate the potential of remediated wastewater for watering urban forestry. © 2024 Elsevier Inc.Item A DFT study of the adsorption behavior and sensing properties of CO gas on monolayer MoSe2 in CO2-rich environment(Springer Science and Business Media Deutschland GmbH, 2024) Vinturaj, V.; Yadav, A.K.; Singh, R.; Garg, V.; Bhardwaj, R.; Ajith, K.M.; Pandey, S.K.Context: Carbon monoxide, also known as the “silent killer,” is a colorless, odorless, tasteless, and non-irritable gas that, when inhaled, enters the bloodstream and lungs, binds with the hemoglobin, and blocks oxygen from reaching tissues and cells. In this work, the monolayer MoSe2-based CO gas sensors were designed using density functional theory calculation with several dopants including Al, Au, Pd, Ni, Cu, and P. Here, Cu and P were found to be the best dopants, with adsorption energies of −0.67 eV (Cu) and −0.54 eV (P) and recovery times of 1.66 s and 13.8 ms respectively. Cu conductivity for CO adsorption was found to be 2.74 times that of CO2 adsorption in the 1.0–2.26 eV range. P displayed the highest selectivity, followed by Pd and Ni. The dopants, Pd and Ni, were found suitable for building CO gas scavengers due to their high recovery times of 9.76 × 1020 s and 2.47 × 1011 s. Similarly, the adsorption of CO2 on doped monolayer MoSe2 was also investigated. In this study, it is found that monolayer MoSe2 could be employed to create high-performance CO sensors in a CO2-rich environment. Method: The electrical characteristics of all doped MoSe2 monolayers are obtained using a DFT calculation with the PBE-GGA method from the Quantum ESPRESSO package. The self-consistent field (SCF) computations were performed using a 7 × 7 × 1 k-point grid and a norm-conserving pseudo potential (NCPP) file. To determine electrical conductivity, the semi-classical version of Boltzmann transport theory, implemented in the Boltz Trap code, was used. © The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature 2024.Item A Molecular-Level Exploration of Dopant-Free Pyrazine-Derived Hole Transport Materials: Investigation of Interfacial Interaction in Perovskite Photovoltaics(John Wiley and Sons Inc, 2025) Sheshachala, A.; Keremane, K.S.; Bhat, V.G.; Karunakar Shankar, S.; Asuo, I.M.; Doumon, N.Y.; Poudel, B.; Udayakumar, U.The development of innovative core structures and peripheral groups for organic hole-transporting materials (HTMs) continues to be a focal point in enhancing the performance of perovskite solar cells (PVSCs). This study reports the design and synthesis of dopant-free pyrazine-based HTMs. PS1 features a D–A–D type structure with pyrazine as the acceptor and 4,4?-dimethoxy triphenylamine (4,4?-OMe-TPA) as the donor, while PS2 adopts a D–?–A–?–D configuration with an additional thiophene unit as ?-spacer along with 4,4?-OMe-TPA as donor. Both compounds are synthesized through a simple two-step synthetic procedure. These HTMs are subjected to structural, photophysical, electrochemical, theoretical, and photoelectrochemical studies with an emphasis on evaluation of structure–property relationships. Theoretical studies are conducted to explore the electronic distribution, optimized molecular structure, and frontier molecular orbitals. Their performance in PVSCs is systematically evaluated without adding dopants. PS2 exhibits superior photoluminescence quenching compared to PS1, indicating more efficient charge transfer from the perovskite layer. Notably, PS2 achieves a power conversion efficiency (PCE) of 11.9%, surpassing the performance of PS1 (PCE of 10.15%). These findings highlight the potential of adjusting the electron-deficient core and ?-bridge units as an effective strategy to optimize the properties of HTMs and improve their performance in PVSC applications. © 2025 Wiley-VCH GmbH.