Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
12 results
Search Results
Item Removal of acutely hazardous pharmaceuticals from water using multi-template imprinted polymer adsorbent(Ecomed Publishers susanne.kuehbandner@hjr-verlag.de, 2014) Venkatesh, A.; Chopra, N.; Krupadam, R.J.Molecularly imprinted polymer adsorbent has been prepared to remove a group of recalcitrant and acutely hazardous (p-type) chemicals from water and wastewaters. The polymer adsorbent exhibited twofold higher adsorption capacity than the commercially used polystyrene divinylbenzene resin (XAD) and powdered activated carbon adsorbents. Higher adsorption capacity of the polymer adsorbent was explained on the basis of high specific surface area formed during molecular imprinting process. Freundlich isotherms drawn showed that the adsorption of p-type chemicals onto polymer adsorbent was kinetically faster than the other reference adsorbents. Matrix effect on adsorption of p-type chemicals was minimal, and also polymer adsorbent was amenable to regeneration by washing with water/methanol (3:1, v/v) solution. The polymer adsorbent was unaltered in its adsorption capacity up to 10 cycles of adsorption and desorption, which will be more desirable in cost reduction of treatment compared with single-time-use activated carbon. © 2014 Springer-Verlag Berlin Heidelberg.Item Conversion of waste polypropylene to liquid fuel using acid-activated kaolin(SAGE Publications Ltd, 2014) Panda, A.K.; Singh, R.K.Waste polypropylene was subjected to thermal degradation in the presence of kaolin and acid-treated kaolin, with different catalyst-to-plastics ratios, in a semi-batch reactor at a temperature range of 400-550°C to obtain optimized process conditions for the production of liquid fuels. The effects of process temperature, catalyst and feed composition on yield and quality of the oil were determined. For a thermal decomposition reaction at up to 450°C, the major product is volatile oil; and the major products at a higher temperature (475-550°C) are either viscous liquid or wax. The highest yield of condensed fraction in the thermal reaction is 82.85% by weight at 500°C. Use of kaolin and acid-treated kaolin as a catalyst decreased the reaction time and increased the yield of liquid fraction. The major product of catalysed degradation at all temperatures is highly volatile liquid oil. The maximum oil yield using kaolin and acidtreated kaolin is 87.5% and 92%, respectively, at 500°C. The oil obtained was characterized using GC-MS for its composition and different fuel properties by IS methods. © The Author(s) 2014.Item Photocatalytic degradation of phenol using Ag core-TiO2 shell (Ag@TiO2) nanoparticles under UV light irradiation(Springer Verlag service@springer.de, 2016) Shet, A.; Shetty K, K.V.Ag@TiO2 nanoparticles were synthesized by one pot synthesis method with postcalcination. These nanoparticles were tested for their photocatalytic efficacies in degradation of phenol both in free and immobilized forms under UV light irradiation through batch experiments. Ag@TiO2 nanoparticles were found to be the effective photocatalysts for degradation of phenol. The effects of factors such as pH, initial phenol concentration, and catalyst loading on phenol degradation were evaluated, and these factors were found to influence the process efficiency. The optimum values of these factors were determined to maximize the phenol degradation. The efficacy of the nanoparticles immobilized on cellulose acetate film was inferior to that of free nanoparticles in UV photocatalysis due to light penetration problem and diffusional limitations. The performance of fluidized bed photocatalytic reactor operated under batch with recycle mode was evaluated for UV photocatalysis with immobilized Ag@TiO2 nanoparticles. In the fluidized bed reactor, the percentage degradation of phenol was found to increase with the increase in catalyst loading. © 2015, Springer-Verlag Berlin Heidelberg.Item Artificial neural network based modeling to evaluate methane yield from biogas in a laboratory-scale anaerobic bioreactor(Elsevier Ltd, 2016) Nair, V.V.; Dhar, H.; Kumar, S.; Thalla, A.K.; Mukherjee, S.; Wong, J.W.C.The performance of a laboratory-scale anaerobic bioreactor was investigated in the present study to determine methane (CH4) content in biogas yield from digestion of organic fraction of municipal solid waste (OFMSW). OFMSW consists of food waste, vegetable waste and yard trimming. An organic loading between 40 and 120 kg VS/m3 was applied in different runs of the bioreactor. The study was aimed to focus on the effects of various factors, such as pH, moisture content (MC), total volatile solids (TVS), volatile fatty acids (VFAs), and CH4 fraction on biogas production. OFMSW witnessed high CH4 yield as 346.65 L CH4/kg VS added. A target of 60–70% of CH4 fraction in biogas was set as an optimized condition. The experimental results were statistically optimized by application of ANN model using free forward back propagation in MATLAB environment. © 2016 Elsevier LtdItem Fenton's treatment of actual agriculture runoff water containing herbicides(IWA Publishing 12 Caxton Street London SW1H 0QS, 2017) Sangami, S.; Manu, B.This research was to study the efficiency of the Fenton's treatment process for the removal of three herbicides, namely 2,4-dichlorophenoxy acetic acid (2,4-D), ametryn and dicamba from the sugarcane field runoff water. The treatment process was designed with the Taguchi approach by varying the four factors such as H 2 O 2 /COD (1-3.5), H 2 O 2 /Fe 2+ (5-50), pH (2-5) and reaction time (30-240 min) as independent variables. Influence of these parameters on chemical oxygen demand (COD), ametryn, dicamba and 2,4-D removal efficiencies (dependent variables) were investigated by performing signal to noise ratio and other statistical analysis. The optimum conditions were found to be H 2 O 2 /COD: 2.125, H 2 O 2 /Fe 2+ : 27.5, pH: 3.5 and reaction time of 135 min for removal efficiencies of 100% for ametryn, 95.42% for dicamba, 88.2% for 2,4-D and with 75% of overall COD removal efficiencies. However, the percentage contribution of H 2 O 2 /COD ratio was observed to be significant among all four independent variables and were 44.16%, 67.57%, 51.85% and 50.66% for %COD, ametryn, dicamba and 2,4-D removal efficiencies, respectively. The maximum removal of herbicides was observed with the H 2 O 2 dosage of 5.44 mM and Fe 2+ dosage of 0.12 mM at pH 3.5. © IWA Publishing 2017 W.Item Effects of electric potential, NaCl, pH and distance between electrodes on efficiency of electrolysis in landfill leachate treatment(Taylor and Francis Inc. 325 Chestnut St, Suite 800 Philadelphia PA 19106, 2017) Erabee, I.K.; Ahsan, A.; Jose, B.; Arunkumar, T.; Sathyamurthy, R.; Idrus, S.; Daud, N.N.N.This study investigated the effects of different parameters on the removal efficiencies of organic and inorganic pollutants in landfill leachate treatment by electrolysis. Different parameters were considered such as the electric potential (e.g., 24, 40 and 60 V), hydraulic retention time (HRT) (e.g., 40, 60, 80, 100 and 120 min), sodium chloride (NaCl) concentration (e.g., 1, 3, 5 and 7%), pH (e.g., 3, 7 and 9), electrodes materials [e.g., aluminum (Al) and iron (Fe)] and distance between electrodes (e.g., 1, 2 and 3 cm). The best operational condition of electrolysis was then recommended. The electric potential of 60 V with HRT of 120 min at 5% of NaCl solution using Al as anode and Fe as cathode (kept at a distance of 3 cm) was the most efficient condition which increased the removal efficiencies of various parameters such as turbidity, salinity, total suspended solids (TSS), total dissolved solids (TDS), biochemical oxygen demand (BOD), chemical oxygen demand (COD) and heavy metals (e.g., Zn and Mn). The higher removal percentages of many parameters, especially COD (94%) and Mn (93%) indicated that the electrolysis is an efficient technique for multi-pollutants (e.g., organic, inorganic and heavy metals) removal from the landfill leachate. © 2017 Taylor & Francis Group, LLC.Item Performance, emission, and combustion characteristics of twin-cylinder common rail diesel engine fuelled with butanol-diesel blends(Springer Verlag service@springer.de, 2017) Lamani, V.T.; Yadav, A.K.; Gottekere, K.N.Nitrogen oxides and smoke are the substantial emissions for the diesel engines. Fuels comprising high-level oxygen content can have low smoke emission due to better oxidation of soot. The objective of the paper is to assess the potential to employ oxygenated fuel, i.e., n-butanol and its blends with the neat diesel from 0 to 30% by volume. The experimental and computational fluid dynamic (CFD) simulation is carried out to estimate the performance, combustion, and exhaust emission characteristics of n-butanol-diesel blends for various injection timings (9°, 12°, 15°, and 18°) using modern twin-cylinder, four-stroke, common rail direct injection (CRDI) engine. Experimental results reveal the increase in brake thermal efficiency (BTE) by ~ 4.5, 6, and 8% for butanol-diesel blends of 10% (Bu10), 20% (Bu20), and 30% (Bu30), respectively, compared to neat diesel (Bu0). Maximum BTE for Bu0 is 38.4%, which is obtained at 12° BTDC; however, for Bu10, Bu20 and Bu30 are 40.19, 40.9, and 41.7%, which are obtained at 15° BTDC, respectively. Higher flame speed of n-butanol-diesel blends burn a large amount of fuel in the premixed phase, which improves the combustion as well as emission characteristics. CFD and experimental results are compared and validated for all fuel blends for in-cylinder pressure and nitrogen oxides (NOx), and found to be in good agreement. Both experimental and simulation results witnessed in reduction of smoke opacity, NOx, and carbon monoxide emissions with the increasing n-butanol percentage in diesel fuel. © 2017, Springer-Verlag GmbH Germany.Item Solar light-driven photocatalysis using mixed-phase bismuth ferrite (BiFeO3/Bi25FeO40) nanoparticles for remediation of dye-contaminated water: kinetics and comparison with artificial UV and visible light-mediated photocatalysis(Springer Verlag service@springer.de, 2018) Kalikeri, S.; Shetty K, V.Mixed-phase bismuth ferrite (BFO) nanoparticles were prepared by co-precipitation method using potassium hydroxide as the precipitant. X-ray diffractogram (XRD) of the particles showed the formation of mixed-phase BFO nanoparticles containing BiFeO3/Bi25FeO40 phases with the crystallite size of 70 nm. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed the formation of quasi-spherical particles. The BFO nanoparticles were uniform sized with narrow size range and with the average hydrodynamic diameter of 76 nm. The band gap energy of 2.2 eV showed its ability to absorb light even in the visible range. Water contaminated with Acid Yellow (AY-17) and Reactive Blue (RB-19) dye was treated by photocatalysis under UV, visible, and solar light irradiation using the BFO nanoparticles. The BFO nanoparticles showed maximum photocatalytical activity under solar light as compared to UV and visible irradiations, and photocatalysis was favored under acidic pH. Complete degradation of AY-17 dyes and around 95% degradation of RB-19 could be achieved under solar light at pH 5. The kinetics of degradation followed the Langmuir–Hinshelhood kinetic model showing that the heterogeneous photocatalysis is adsorption controlled. The findings of this work prove the synthesized BFO nanoparticles as promising photocatalysts for the treatment of dye-contaminated industrial wastewater. © 2018, Springer-Verlag GmbH Germany, part of Springer Nature.Item Experimental study of methyl tert-butyl ether as an oxygenated additive in diesel and Calophyllum inophyllum methyl ester blended fuel in CI engine(Springer Verlag service@springer.de, 2018) Bragadeshwaran, A.; Kasianantham, N.; Ballusamy, S.; Tarun, K.R.; Arumuga Perumal, D.A.; Kaisan, M.U.This work presents the effect of the ternary oxygenated additive on diesel biodiesel blended fuel to evaluate the engine characteristics. The Calophyllum inophyllum trees being abundant in India can lessen the dependence on petroleum imports to a specific extent. Methyl tertiary butyl ether is used as an oxygenated additive for the ternary blends preparation as 5–20% by volume. Seven blends of neat baseline diesel, biodiesel (Calophyllum inophyllum Methyl Ester), a blend of diesel (50%)-biodiesel (50%), a blend of diesel (50%)-biodiesel-methyl tert-butyl ether (5, 10, 15, and 20%) are prepared which are tested on a single cylinder, constant speed diesel engine. The experimental results were revealed that the replacement of biodiesel by MTBE has shown a slight reduction in brake thermal efficiency with a slight increase in brake-specific fuel consumption. Further, the MTBE addition in ternary blends reduced the unburned hydrocarbon, CO, and NOx by 63.9, 6.4, and 3.37% respectively. In addition, the carbon dioxide emission is almost similar to diesel fuel at a higher addition of MTBE with diesel-biodiesel blend. In the combustion point of view, the addition of 5% MTBE resulted in 3.49 and 5.1% reduction of peak pressure and heat release rate are observed as compared to diesel fuel. Critical analysis in combustion aspects is also carried out and it is witnessed with prolonged ignition delay during MTBE addition with diesel-biodiesel blends. © 2018, Springer-Verlag GmbH Germany, part of Springer Nature.Item Kinetic and equilibrium modeling of biosorption of nickel (II) and cadmium (II) on brewery sludge(IWA Publishing 12 Caxton Street London SW1H 0QS, 2019) Kulkarni, R.M.; Shetty K, K.; Srinikethan, G.In the current study, utilization of industrial waste brewery sludge for the biosorption of nickel (II) and cadmium (II) has been explored. The suitable conditions for the effective removal of Ni (II) and Cd (II) from aqueous solutions were examined. The kinetic evaluation showed that the biosorption process using the sludge followed pseudo-second order kinetics. In the presence of a metal co-ion, competitive and preferential biosorption was observed. The Langmuir model and Freundlich model were able to describe the sorption equilibrium for biosorption of Ni (II) and Cd (II) ions in single and dual metal systems. The effects of co-ion concentrations onto mono-component isotherm parameters (Langmuir and Freundlich) were studied and the inhibitory effect of co-ion concentration was observed. The effective reusability of biomass was assessed by three cycles of sorption-desorption. The sludge, owing to its high biosorption intensity and large availability from the local supply, is a better biosorbent for the treatment of Ni (II) and Cd (II) contaminated water. © IWA Publishing 2019 Water Science & Technology.