Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Has files: NoSubject: search.filters.subject.Slot antennas

Search Results

Now showing 1 - 10 of 23
  • No Thumbnail Available
    Item
    A tri-band slot antenna loaded with split ring resonators
    (John Wiley and Sons Inc. P.O.Box 18667 Newark NJ 07191-8667, 2017) Paul, P.M.; Kandasamy, K.; Sharawi, M.S.
    A compact tri-band slot antenna with independent tuning capability of its resonant frequencies is proposed in this article. A microstrip line fed square slot is loaded with split ring resonators (SRR) to obtain multiband characteristics. The slot is designed to resonate at 2.6 GHz. Two SRRs with single and multiple splits are loaded with the slot, which provide additional resonances at 4.3 and 4.7 GHz, respectively. Parametric analysis of the antenna shows that its resonance frequencies are controlled independently. The proposed antenna is fabricated on an FR4 substrate with a size of 60 × 60 × 1.56 mm2. The proposed design offers stable omnidirectional patterns and >3.8 dBi at all the resonating frequency bands. © 2017 Wiley Periodicals, Inc.
  • No Thumbnail Available
    Item
    A Zero Index Based Meta-Lens Loaded Wideband Directive Antenna Combined with Reactive Impedance Surface
    (Institute of Electrical and Electronics Engineers Inc., 2018) Majumder, B.; Kandasamy, K.; Ray, K.P.
    In this paper, an aperture efficient wideband high-gain patch antenna is designed using a novel multilayer-based metamaterial structure combined with a reactive impedance surface (RIS)-backed patch antenna. The metamaterial unit cell is a two-layer structure which is stacked one after other to form the overall unit cell. The microscopic behavior of the proposed unit cell has been investigated. This unit cell gives low refractive index over a wide bandwidth with a negligible loss. An RIS-backed patch antenna has been designed in the required frequency band to feed the multilayer zero-index metamaterial medium. The introduction of this surface is to provide unidirectional radiation over a wideband in the zero refractive index region. The proposed antenna gives a 14% fractional bandwidth over the $C$ - and $X$ -bands. The proposed antenna enhances the peak gain of the conventional patch antenna by an amount of 8.5 dB at 8 GHz. Finally, the antenna has been fabricated and its performance is verified experimentally. © 2013 IEEE.
  • No Thumbnail Available
    Item
    A triband circularly polarized strip and SRR-loaded slot antenna
    (Institute of Electrical and Electronics Engineers Inc., 2018) Paul, P.M.; Kandasamy, K.; Sharawi, M.S.
    In this communication, a simple and compact multiband circularly polarized (CP) slot antenna loaded with metallic strips and a split-ring resonator (SRR) is proposed. The multiband operation is obtained via exciting the SRR and copper strips by the microstrip-fed square slot antenna. The SRR resonates at 1.83 GHz, while the strips and the slot antenna provide resonances at 2.5 and 3.1 GHz. Resonant modes of loaded SRR and strips combined with the fundamental mode of the slot produce CP waves at the resonance frequencies of the proposed antenna. The proposed antenna allows for independent tuning of different bands via the use of the tilted strips and the SRR. Also, the sense of polarization at the resonance frequencies can be controlled by changing the orientation of the strips and the SRR with respect to the slot. The proposed antenna is fabricated on an FR-4 substrate of dimension 50 × 50 × 1.56 mm3. Antenna performances in terms of 10 dB return loss bandwidth, 3 dB axial ratio bandwidth, gain, and efficiency are validated experimentally and are in a good agreement with the simulated results. © 2018 IEEE.
  • No Thumbnail Available
    Item
    Dispersion-Engineered Transmission Line Loaded Slot Antenna for UWB Applications
    (Institute of Electrical and Electronics Engineers Inc., 2019) Paul, P.M.; Kandasamy, K.; Sharawi, M.S.; Majumder, B.
    A transmission line (TL) loaded, compact, ultrawideband (UWB) square slot antenna is proposed in this letter. The square slot is a microstrip line fed and loaded with an array of periodically perturbed TLs to achieve a UWB response from 2.1 to 11.5 GHz. The slot is designed to resonate at 2.6 GHz. The TLs are dispersion engineered to resonate at several frequencies so as to provide a wideband response. Loading of the engineered TLs on the square slot produced multiple resonances without affecting the fundamental mode of the slot antenna. The proposed antenna design is analyzed using dispersion relations and equivalent circuits. The proposed antenna is fabricated on an RT/Duroid 5880 substrate with a size of 50 × 50 × 1.52 mm3. The antenna performance metrics, such as impedance bandwidth, gain, and efficiency, are experimentally verified. Good agreement is obtained between simulated and measured results. © 2018 IEEE.
  • No Thumbnail Available
    Item
    Reconfigurable Wide Bandwidth Using Novel Extraction Technique of Slotted Monopole Antenna with RF CNT Network
    (Springer New York LLC barbara.b.bertram@gsk.com, 2019) Kumar, S.; Song, H.; Kanuajia, B.K.
    This work first moment focuses on the concept of reconfigurable wide bandwidth using novel extraction technique of slotted monopole antenna with RF carbon nanotube (CNT) network. The entire approach is folded into four different designs. The first design proposes a monopole antenna where asymmetric flower type corners and mushroom shape encloses by T-slot is cut on the patch. This new shaped antenna covers wide impedance bandwidth of about 14.5 GHz within range from 21.5 to 36 GHz. The proposed antenna observed that lower bands are excited with new resonating modes by inserting T-slot upon mushroom shape while higher bands are effected due to asymmetric flower type corners on the patch. A wide range of gain from 16.3 to 20.5 dB with maximum axial ratio bandwidth of 2.8% is also succeed. Measured and simulation results for proposed antenna shows good agreement with each other. In second design, a novel extraction technique is used for equivalent model of slotted monopole antenna which shows promising agreement with the original geometry. Thirdly, introduces RF CNT equivalent model which demonstrates its ability to resonant at wideband within range of 12.4–25.1 GHz with 68% of fractional impedance bandwidth. Finally, RF equivalent model of slotted monopole antenna is integrated with CNT for the proper operation. The fabrication of integration network scenario proves notability of reconfiguration in aspect of wide bandwidth with the compactness. A frequency switchable notability dominant some excited additional resonant modes using proper impedance matching between proposed antenna and RF CNT. This proposed work is fascinating to our integration network which fully covered K-band and almost for Ka-band application. © 2018, Springer Science+Business Media, LLC, part of Springer Nature.
  • No Thumbnail Available
    Item
    Investigation of CMOS Based Integration Approach Using DAI Technique for Next Generation Wireless Networks
    (Springer New York LLC barbara.b.bertram@gsk.com, 2019) Roy, G.M.; Kanuajia, B.K.; Dwari, S.; Kumar, S.; Song, H.
    This research work investigates a CMOS based low noise amplifier (LNA) using differential active inductor with eight-shaped patch antenna for next generation wireless communication. The proposed work conceded into three different phases. The first phase proposes LNA architecture which includes multistage cascode amplifier with a gate inductor gain peaking technique. The ground approach for this architecture employs active inductor technique that includes two stages of differential amplifier. The proposed novel technique leads to give incremental in inductance by using of common mode feedback resistor and lowers the undesirable parasitic resistance effect. Additionally, this technique offers gain enhanced noise cancellation and achieves a frequency band of around 5.7 GHz. The proposed architecture includes single stage differential AI and enhances the bandwidth up to 6.8 GHz with peak gain of 21 dB at 7.8 GHz. The noise figure and stability factor are achieved which is reasonably good at 1 dB. The proposed architecture is design and optimized on advanced design RF simulator using 0.045 µm CMOS process technology. While in second phase, a narrow band eight-shaped patch antenna is designed which provides operating band range from 5.8 to 6.5 GHz with 6.2 GHz resonating frequency. Highest peak gain of 15 dB and maximum radiation power of 42.5 dBm is succeed by proposed antenna. The final phase provides integration strategy of LNA with antenna and achieves desired gain of nearly 21 dB with minimum NF of 1.2–1.5 dB in the same band. © 2018, Springer Science+Business Media, LLC, part of Springer Nature.
  • No Thumbnail Available
    Item
    A High-Gain Circularly Polarized Antenna Using Zero-Index Metamaterial
    (Institute of Electrical and Electronics Engineers Inc., 2019) Tharehalli Rajanna, P.K.T.; Rudramuni, K.; Kandasamy, K.
    In this letter, a novel high-gain circularly polarized (CP) antenna based on the zero-index metamaterial (ZIM) is presented. A square ring with two asymmetrical splits is used as a unit cell to achieve high gain and circular polarization. The 9 × 9 periodic array unit cells act as an aperture efficient focusing metasurface lens and polarization converter for a primary source antenna. The focusing effect of the ZIM enhances the gain of the microstrip patch antenna placed above it by an amount of 5-6 dB. Also, the ZIM converts the linearly polarized wave emitted by the patch antenna into circularly polarized waves. The circular polarization is achieved by optimizing the two split gaps on the ring of the unit cell, which gives two orthogonal polarizations with the required phase. The proposed design is fabricated and verified experimentally. The prototype has measured impedance bandwidth from 7.04 to 7.68 GHz. The 3 dB axial ratio is achieved from 7.11 to 7.56 GHz, with a peak gain of 12.31 dBic at 7.45 GHz. The gain of around 11.5 dBic is achieved over the entire CP bandwidth with a good cross-polarization level. © 2002-2011 IEEE.
  • No Thumbnail Available
    Item
    Compact triband circularly polarized planar slot antenna loaded with split ring resonators
    (John Wiley and Sons Inc. P.O.Box 18667 Newark NJ 07191-8667, 2019) Tharehalli Rajanna, P.K.T.; Rudramuni, K.; Kandasamy, K.
    In this article, a coplanar waveguide (CPW) fed triband circularly polarized (CP) planar slot antenna loaded with split ring resonators (SRRs) is presented. The truncated slot antenna resonates at 4.15 GHz, which gives two orthogonal degenerate modes to produce circular polarization at the first band. The second and third band resonances are achieved at 4.77 GHz and 5.1 GHz respectively due to the loading of SRRs on the slot antenna. The electric fields produced by the single and multiple split gaps in each ring of SRR1 and SRR2 produce CP at the second and third band. All three bands are tuned independently to achieve optimized axial ratio bandwidth. The antenna is fabricated and verified experimentally. The measured results give impedance bandwidth of 64.54% and axial ratio bandwidths of 11.76%, 1.9%, and 3.87% at first, second, and third band, respectively. © 2019 Wiley Periodicals, Inc.
  • No Thumbnail Available
    Item
    A corner expanded slot antenna loaded with copper strips for dual-band circular polarization characteristics
    (John Wiley and Sons Inc. P.O.Box 18667 Newark NJ 07191-8667, 2020) Paul, P.M.; Kandasamy, K.; Sharawi, M.S.
    In this article, the design and implementation of a dual-band circularly polarized (CP) microstrip line fed square slot antenna with compact size is proposed. The proposed CP antenna consists of a square slot antenna with a pair of symmetric rectangular extensions on opposite corners and loaded with an array of inclined and truncated rectangular copper strips. The square slot with diagonal extensions resonates at 2.24 to 2.62 GHz with a 3 dB axial ratio (AR) bandwidth of 15.7%. Besides, loading it with an array of inclined and truncated rectangular copper strips helps produce a resonance at higher band with CP. The higher band operates between 3.26 and 5.18 GHz and centered at 4.52 GHz, with a 3 dB AR bandwidth of 45.5%. The polarization sense and resonant frequency of the proposed antenna can be independently tuned depending on the position and dimensions of the slot and strips, respectively. The proposed antenna is fabricated and measured in terms of impedance bandwidth, axial ratio bandwidth, peak gain, and radiation efficiency. Good agreement between the simulations and measurements of the prototype is obtained. © 2019 Wiley Periodicals, Inc.
  • No Thumbnail Available
    Item
    A novel chaotic modulation approach of packaged antenna for secured wireless medical sensor network in E-healthcare applications
    (John Wiley and Sons Inc. P.O.Box 18667 Newark NJ 07191-8667, 2020) Jayawickrama, C.; Kumar, S.; Chakrabartty, S.; Song, H.
    This article first time reports the chaotic modulation approach toward RF signal processing for secured wireless medical sensor network (WMSN) in E-healthcare applications. A Lorenz based chaotic modulation approach is implemented which provides lowest bit error rate (BER). The definite analytical expressions for BER in a differential chaos-shift keying (DCSK) modulation scheme is derived and it predicted good correlation between simulated and theoretical. It is observed that proposed Lorenz chaos-based DCSK modulation scheme is a potential candidate to provide high security in the patient data for WMSN. An off-body UWB slotted antenna is designed which could avoid limitation of short-range distance like implanted ones. The entire work includes numerical, simulated and experimental data in three phases. In first phase, Lorenz chaotic oscillator with electronics compatibility is executed which acts as data acquisition unit and demonstrates two-dimensional and three-dimensional chaos attractors. While in the second phase, analysis of BER achieves value of less than 10?4 by providing pseudorandom bit sequence at 5 Gb/s. A chaos modulated envelope using Lorenz based DCSK modulation is obtained by delay element ?. Finally, the third phase is designed on-wafer off-body antenna and demonstrates 3.1 to 10.6 GHz UWB toward RF signal processing in E-healthcare applications. © 2019 Wiley Periodicals, Inc.