Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item A proposal for a correlation to calculate pressure drop in reticulated porous media with the help of numerical investigation of pressure drop in ideal & randomized reticulated structures(Elsevier Ltd, 2021) Rambabu, S.; Kartik Sriram, K.; Chamarthy, S.; Parthasarathy, P.; Velamati, V.This paper presents a numerical investigation to estimate pressure drop in fluid flow through reticulated ideal and randomized porous structures. The 3D open-cell foam geometries are constructed using an in-house code along with the use of visualization tool kit (VTK) libraries. In this study, the ideal and randomized Kelvin structures with different porosities and pore densities are generated. These structures have been used to perform direct pore level simulations (DPLS) with the aid of a commercial CFD software. The simulation results are used to acquire the pressure drop across the structures. The pressure drop variation with respect to pore density, porosity, specific surface area, and randomization are analyzed and a pressure drop correlation for reticulated structures with new values of viscous and inertial coefficients is proposed. The validity of the proposed correlation is compared against the experimental and numerical data of the real structures that are available in the literature. © 2021 Elsevier LtdItem Various trade-off scenarios in thermo-hydrodynamic performance of metal foams due to variations in their thickness and structural conditions(MDPI, 2021) Trilok, G.; Gnanasekaran, N.; Mobedi, M.The long standing issue of increased heat transfer, always accompanied by increased pressure drop using metal foams, is addressed in the present work. Heat transfer and pressure drop, both of various magnitudes, can be observed in respect to various flow and heat transfer influencing aspects of considered metal foams. In this regard, for the first time, orderly varying pore density (characterized by visible pores per inch, i.e., PPI) and porosity (characterized by ratio of void volume to total volume) along with varied thickness are considered to comprehensively analyze variation in the trade-off scenario between flow resistance minimization and heat transfer augmentation behavior of metal foams with the help of numerical simulations and TOPSIS (Technique for Order of Preference by Similarity to Ideal Solution) which is a multi-criteria decision-making tool to address the considered multi-objective problem. A numerical domain of vertical channel is modelled with zone of metal foam porous media at the channel center by invoking LTNE and Darcy–Forchheimer models. Metal foams of four thickness ratios are considered (1, 0.75, 0.5 and 0.25), along with varied pore density (5, 10, 15, 20 and 25 PPI), each at various porosity conditions of 0.8, 0.85, 0.9 and 0.95 porosity. Numerically obtained pressure and temperature field data are critically analyzed for various trade-off scenarios exhibited under the abovementioned variable conditions. A type of metal foam based on its morphological (pore density and porosity) and configurational (thickness) aspects, which can participate in a desired trade-off scenario between flow resistance and heat transfer, is illustrated. © 2021 by the authors. Licensee MDPI, Basel, Switzerland.Item Numerical assessment of thermal characteristics of metal foams of orderly varied pore density and porosity under different convection regimes(Elsevier Masson s.r.l., 2022) Trilok, G.; Kumar, K.K.; Gnanasekaran, N.; Mobedi, M.The present study is done to analyze heat transfer and fluid flow in a channel with orderly varied pore density and porosity combination of foam samples. Darcy Forchheimer flow and LTNE thermal models are considered to estimate heat transfer characteristics. Considering the effect of orderly varied combinations of the dual structural properties, forced convection over a range of flow velocities and natural convection phenomenon are studied numerically in the channel housing porous samples. Two limiting solutions for Nusselt number (Nu) i.e., Nun (for natural convection) and Nuf (for forced convection) for Ri→∞ and Ri→0 respectively, as a function of independent variable Richardson number (Ri) with structural properties pore density and porosity are obtained with the help of local thermal non-equilibrium (LTNE) thermal model and Darcy-Forchheimer flow model. Further these asymptotic solutions are blended using technique illustrated in the literature in order to obtain solution for Nusselt number for mixed convection (Num). Correlations for Nusselt number as a function of combination of porosity and pore density are obtained emphasizing on the varied significance of these parameters in different convection regime. The present study not only emphasizes on effect of combination of structural properties of metal foams on heat transfer characteristics, but also illustrates a technique that enables to arrive at suitable correlation for an intermediate phenomenon existing between two other extremes, with zero computational cost. Effect of pore density on heat transfer characteristics at a given porosity, is found to be not much influencing in natural convection dominant regime. However, in mixed and forced convection dominant scenario it is illustrated that, effect of variation in pore density and porosity plays a significant role in expressing distinguishable heat transfer characteristics, along with other well-known independent parameters such as porosity and Reynolds number. © 2021 Elsevier Masson SASItem Correlations and Numerical Modeling of Stacked Woven Wire-Mesh Porous Media for Heat Exchange Applications(MDPI, 2022) Trilok, G.; Srinivas, K.E.S.; Harikrishnan, D.; Gnanasekaran, N.; Mobedi, M.Metal foams have gained attention due to their heat transfer augmenting capabilities. In the literature, correlations describing relations among their morphological characteristics have successfully been established and well discussed. However, collective expressions that categorize stacked wire mesh based on their morphology and thermo-hydraulic expressions required for numerical modeling are less explored in the literature. In the present study, cross relations among the morphological characteristics of stacked wire-mesh were arrived at based on mesh-size, wire diameter and stacking type, which are essential for describing the medium and determining key input parameters required for numerical modeling. Furthermore, correlation for specific surface area, a vital parameter that plays a major role in interstitial heat transfer, is provided. With the arrived correlations, properties of stacked wire-mesh samples of orderly varied mesh-size and porosity are obtained for various stacking scenarios, and corresponding thermo-hydraulic parameters appearing in the governing equations are evaluated. A vertical channel housing the categorized wire-mesh porous media is numerically modeled to analyze thermal and flow characteristics of such a medium. The proposed correlations can be used in confidence to evaluate thermo-hydraulic parameters appearing in governing equations in order to numerically model various samples of stacked wire-mesh types of porous media in a variety of heat transfer applications. © 2022 by the authors. Licensee MDPI, Basel, Switzerland.Item Multi-Objective Optimization of Hybrid Heat Sinks with Phase Change Materials(Taylor and Francis Ltd., 2024) Nedumaran, M.S.; Trilok, G.; Gnanasekaran, N.; Hooman, K.A passive method with phase change material (PCM) is an appropriate technique in electronic cooling. But, due to its poor thermal conductivity, many enhancers are employed to reduce the thermal resistance offered by the PCM. A partial filling strategy to reduce the cost and weight of foams with fins is used in this study. A hybrid heat sink with a combination of fins placed at the sidewalls of the enclosure and foams filled at certain heights such as 10, 20, and 30 mm is considered in this present work. A two-dimensional numerical model with n-eicosane as PCM is developed in ANSYS Fluent 19. A multi-objective optimization is carried out using a reliable multi criteria decision making approach. Different weightage is distributed to the objective functions in this method depending on the choice of the user. The pore size and density vary for various filling heights, and 60 cases are investigated for both charging and discharging cycles. The pore size of 0.8-0.95 and pore density of 5-25 pores per inch with a broad range is considered. From the discussions, guidelines for selecting a preferable pore size and pore density can be determined based on the filling height and applied weightage. © 2023 Taylor & Francis Group, LLC.