Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item Elevated temperatures erosion wear behavior of HVOF sprayed WC-Co-Cr/Mo coatings on Ti6Al4V substrate(Elsevier B.V., 2023) Behera, N.; Medabalimi, S.; Ramesh, M.R.The present research aims to investigate the effect of different impact angles and temperatures on volumetric erosion loss of WC-Co-Cr coating containing 10 wt% Mo. The composite coating was developed using High-Velocity Oxy Fuel (HVOF) process on a titanium substrate (Ti-31). A solid particle erosion behavior of the coatings is carried out at different impact angles (30°, 60°, and 90°) and temperatures (200 °C, 400 °C,600 °C, and 800 °C). The volumetric erosion loss of the coated samples was measured using an air jet erosion tester at high temperatures using Al2O3 as an erodent. The XRD, SEM/EDS, porosity, density, microhardness, bond strength, and scratch tests characterized the as-sprayed coatings. The 3D optical profilometer was employed to evaluate the volumetric erosion loss and the mode of erosion. The scratch resistance of WC-Co-Cr coating is better than WC-Co-Cr/Mo coating. The WC-Co-Cr coating shows a brittle mode of erosion up to 600 °C and a ductile mode of erosion at 800 °C. In contrast, the WC-Co-Cr/Mo coating shows a brittle mode of erosion at 200 °C and a mixed mode of erosion at 400 °C to 800 °C. The volumetric erosion loss of WC-Co-Cr is less than WC-Co-Cr/Mo for all temperatures and impact angles. The formation of oxide phases on the coating surfaces demonstrates erosion resistance at high temperatures. The results of volumetric erosion loss measured by the weight loss method correlate well with a non-contact type 3D optical profilometer. © 2023 Elsevier B.V.Item Effect of Impact Angles and Temperatures on the Solid Particle Erosion Behavior of HVOF Sprayed WC-Co/NiCr/Mo and Cr3C2-CoNiCrAlY Coatings(Springer, 2023) Behera, N.; Medabalimi, S.; Ramesh, M.R.Extreme erosion wear from elevated temperature caused by the impact of entrained solid particles in the fluid stream primarily affects aerospace components and marine parts. This work focuses on increasing the base material erosion resistance by applying thermally sprayed carbide-based coatings. A high-temperature Solid particle erosion behavior of WC-Co/NiCr/Mo and Cr3C2-CoNiCrAlY coatings deposited by the HVOF process on a titanium-31 was evaluated using an air-jet erosion tester. The erosion test was conducted utilizing alumina erodent of grit size 35-50 µm. The effects of impact angles (30°, 60°, and 90°) and temperatures (200-800 °C) on the erosion performance of two coatings are compared. The feedstock powder and as-sprayed coatings were characterized for micro-structure phase composition, porosity, density, micro-hardness, and adhesion strength. SEM/EDS and a 3D optical profilometer were used to examine eroded samples further to determine the erosion mode. The Cr3C2-CoNiCrAlY coating shows a brittle mode behavior of erosion at 200-400 °C and ductile mode behavior of erosion at 600-800 °C. In contrast, the WC-Co/NiCr/Mo coating shows brittle mode behavior of erosion at 200-400 °C and 600-800 °C, a mixed mode behavior of erosion. The erosion loss in volume of Cr3C2-CoNiCrAlY is lower than WC-Co/NiCr/Mo for all temperatures and impact angles. The development of carbide and oxide phases on the eroded surfaces demonstrates increasing erosion resistance at high temperatures. The optical profilometer measures the volumetric erosion loss, compares it with the weight loss method, and finds consistency between them. © 2023, ASM International.Item An investigation on tribological performance in HVOF sprayed of Amdry1371 and Amdry 1371/WC-Co coatings on Ti6Al4V(Elsevier B.V., 2024) Behera, N.; Srihari, M.; Sharma, Y.K.; Ramesh, M.R.This study investigates the effect of 30 wt% WC addition into Mo-based coating on the microstructure and dry sliding wear performance at elevated temperatures. A ball-on disk tribometer assessed coating wear and friction behavior at room temperature (RT), 300, and 600 °C with loads of 10 and 20 N. The wear rate and mechanism were assessed using SEM-EDX and an optical profilometer. The coating characteristics included density, porosity, surface roughness, microstructure, and microhardness. The bond strength of Amdry1371 and Amdry1371/30%WC-Co coatings is analyzed using the scratch test. During the scratch test, both coatings show cohesive failure at 30-50 N and cohesive along with adhesive failure at 70 N loads. Compared to Amdry1371 coating, Amdry1371/30%WC-Co coating has greater microhardness and bond strength. The wear rate and friction coefficients of Amdry1371 and Amdry1371/30%WC-Co coatings increase with temperatures up to 300 °C and decrease at 600 °C. Wear debris is generated when contact surfaces fracture under the applied load, acting as a third body in the sliding process. This phenomenon, observable from room temperature to 300 °C, increases wear rate and friction coefficients. Protective oxide phases formed on worn surfaces like MoO3, NiMO4, CoWO4, Cr3O8, and WO3 film at 600 °C. This glaze layer is present on worn surfaces, significantly reducing friction coefficients and the wear rate of coatings. Amdry1371/30%WC-Co coating exhibits superior wear resistance and lower friction coefficients than Amdry1371 coating due to MoO3 and WO3. At RT, the dominant abrasive wear mechanism shifts to oxidative wear at 600 °C for both coatings. © 2024 Elsevier B.V.Item Effect of molybdenum on high-temperature tribological performance in HVOF sprayed of WC-based coatings on superni-76(SAGE Publications Ltd, 2025) Behera, N.; Sarmah, P.; Chandramouli, T.V.; Ramesh, M.R.This study examines the effects of Mo on the high-temperature wear and friction behavior of HVOF-sprayed 70%WC-Co/25%Mo/5%C and 70%WC-CrC-Ni/30%Mo coatings on Superni-76. The ball-on-disc tribometer wear tests were conducted at different temperatures (300°C and 600°C) and loads (10 and 30?N) against counter body Al2O3 ball. Microstructures and phase formation were investigated using SEM/EDS and XRD. The characterization of coating microhardness, surface roughness, and coating density was examined. The 70%WC-Co/25%Mo/5%C coating showed lower surface roughness and higher microhardness values than the 70%WC-CrC-Ni/30%Mo coating. The wear rate of the substrate increases with an increase in temperature, whereas 70%WC-Co/25%Mo/5%C and 70%WC-CrC-Ni/30%Mo coatings decrease with temperature from 300°C to 600°C. The coefficient of friction of substrate and coating decreases with increasing temperatures. The worn surfaces of 70%WC-Co/25%Mo/5%C and 70%WC-CrC-Ni/30%Mo coating contain oxide phases (WO3, Cr2O5) and lubrication phases (M0.2W0.8O3, CoMoO4, and MoO3) at 600°C. These oxide phases reduced the coating wear rate and coefficient of friction at 600°C. The 70%WC-Co/25%Mo/5%C coating showed improved resistance to wear and lower friction coefficient than the substrate and 70%WC-CrC-Ni/30%Mo coating. At temperatures of 300°C, the main abrasive wear mechanism changes to oxidative wear when the temperature reaches 600°C for both coatings. © The Author(s) 2025.Item Surface enhancement of SS304 for high-temperature wear resistance using laser cladded Mo-alloyed stellite 6 coatings(Elsevier B.V., 2025) Aprameya, C.R.; Joladarashi, S.; Ramesh, M.R.Severe wear often limits the high-temperature durability of SS304 components, necessitating the development of surface-engineered solutions. In this investigation, Mo-reinforced Stellite 6 claddings were developed using Laser Directed Energy Deposition (L-DED) to provide enhanced surface protection. Claddings with (3, 6, and 9 wt%) Mo reinforcement enhanced hardness by 2.9, 3.1, and 3.3 times, respectively, compared to the SS304 substrate. This improvement is attributed to Mo-induced solid solution strengthening and the formation of hard intermetallic phases. Dry sliding wear tests were conducted at RT and 600 °C under (10 and 20 N) loads. Wear characterisation of the clads was performed using OM, XRD, FE-SEM, EDX, and Raman spectroscopy. At RT, claddings primarily exhibited abrasive wear with minor plastic deformation. However, at 600 °C, the wear mechanism evolved into a combination of severe adhesive, oxidative, abrasive, and plastic deformation modes, with oxidative wear governing the tribological behavior. Stellite 6 with 9 wt% Mo clads exhibited better tribological performance than the other two variants, owing to the development of oxide glaze layers of Cr2O3, NiO, CoO2, and Co3O4. Enhanced performance of the claddings is attributed to solid solution strengthening, Cr-rich carbide formation, increased dislocation density, and the L-DED technology enabling refined microstructure and strong metallurgical bonding. These findings highlight the potential for further advancements in Mo-reinforced Stellite 6 L-DED claddings for high-temperature wear applications. © 2025 Elsevier B.V.