Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
17 results
Search Results
Item Natural Convection Through High Porosity Metal Foams—A Numerical Study(Springer Science and Business Media Deutschland GmbH, 2021) Kotresha, B.; Jadhav, P.H.; Gnanasekaran, N.Numerical analysis of natural convection through highly porous metal foams attached to the aluminium plates is performed in this study. A heater sandwiched between two aluminium plates attached with aluminium metal foams of different pores per inch (PPI) is considered for the present analysis. Initially, experiments are carried out for aluminium plate-heater assembly for different heat inputs. In the numerical investigation, the aluminium plates are attached with metal foams on either side for further analysis. A well-known Darcy extended Forchheimer flow and LTNE thermal models are considered for the metal foam in the computations. The natural convection is modelled using Boussinesq approximation. Initially, the numerical result for the plate without metal foam is validated with the experimental results for different heat inputs. The results show that the Nusselt number decreases with the increase of metal foam pore density (PPI) and increases with the increase in Rayleigh number. © 2021, The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.Item Numerical investigations of free and forced convection with various features using mesoscopic Lattice Boltzmann method(Elsevier Ltd, 2022) Bhatt, T.; Arumuga Perumal, D.; Anbalagan, A.This paper is concerned with the free and forced convection of heat transfer characteristics by Lattice Boltzmann method (LBM). The LBM is used as the alternative method for the prediction of fluid flow and heat transfer characteristics for the past few years. The fluid flow equation was combined with energy equation in order to get the temperature field in the flow. In natural convection problem, the motion of the fluid inside a cavity domain is considered. The motion takes place because of change in density and due to the gravitational force. The problem of natural convection and forced convection is solved using internal energy density distribution function model for Rayleigh number ranging from 103 to 106. And for the forced convection problem the Reynolds number is varied. In all the problems streamline patterns are plotted, where the intricate details of the flow such as primary and secondary vortices are captured. Thus, it is shown that Lattice Boltzmann Method can be used to solve fluid flow and heat transfer characteristics. © 2022Item Effect of boundary conditions and convection on thermally induced motion of beams subjected to internal heating(2007) Malik, P.; Kadoli, R.; Ganesan, N.Numerical exercises are presented on the thermally induced motion of internally heated beams under various heat transfer and structural boundary conditions. The dynamic displacement and dynamic thermal moment of the beam are analyzed taking into consideration that the temperature gradient is independent as well as dependent on the beam displacement. The effect of length to thickness ratio of the beam on the thermally induced vibration is also investigated. The type of boundary conditions has its influence on the magnitude of dynamic displacement and dynamic thermal moment. A sustained thermally induced motion is observed with progress of time when the temperature gradient being evaluated is dependent on the forced convection generated due to beam motion. A finite element method (FEM) is used to solve the structural equation of motion as well as the heat transfer equation. © Springer-Verlag 2007.Item Transient analysis of subcritical/supercritical carbon dioxide based natural circulation loops with end heat exchangers: Numerical studies(Elsevier Ltd, 2014) Yadav, A.K.; Ram Gopal, M.; Bhattacharyya, S.Transient analysis of carbon dioxide based natural circulation loop (NCL) with end heat exchangers has been carried out. Subcritical and supercritical phases of CO2 are considered with operating pressures in the range of 50-100 bar for an operating temperature range of 323 K to 363 K. Studies are carried out for various loop tilt angles, different initial conditions, and different water mass flow rates. Results: are obtained for various inlet temperatures of water in the hot heat exchanger while keeping the inlet temperature of cooling water in the cold heat exchanger fixed. Effect of tilting the loop in XY and YZ planes on transient as well as steady state behaviour of loop are also studied. Validation of simulation results against experimental and numerical results reported in the literature in terms of modified Grashof number (Grm) and Reynolds number (Re) show good agreement. © 2014 Elsevier Ltd. All rights reserved.Item Effect of tilt angle on subcritical/supercritical carbon dioxide-based natural circulation loop with isothermal source and sink\(American Society of Mechanical Engineers (ASME) infocentral@asme.org, 2016) Yadav, A.K.; Ram Gopal, M.R.; Bhattacharyya, S.In recent years, a growing popularity of carbon dioxide (CO2) as a secondary fluid has been witnessed in both forced as well as in natural circulation loops (NCLs). This may be attributed to the favorable thermophysical properties of CO2 in addition to the environmental benignity of the fluid. However, an extensive literature review shows that studies on CO2-based NCLs are very limited. Also, most of the studies on NCLs do not consider the three-dimensional variation of the field variables. In the present work, threedimensional computational fluid dynamics (CFD) models of a NCL with isothermal source and sink have been developed to study the effect of tilt angle in different planes. Studies have been carried out employing subcritical (liquid and vapor) as well as supercritical phase of CO2 as loop fluid at different operating pressures and temperatures. Results are obtained for a range of tilt angles of the loop, and a significant effect is observed on heat transfer, mass flow rate, and stability of the loop. It was also found that changing the orientation of the loop could be an elegant and effective solution to the flow instability problem of NCLs.Item Optimum Operating Conditions for Subcritical/Supercritical Fluid-Based Natural Circulation Loops(American Society of Mechanical Engineers (ASME) infocentral@asme.org, 2016) Yadav, A.K.; Bhattacharyya, S.; Ram Gopal, M.R.Natural circulation loop (NCL) is simple and reliable due to the absence of moving components and is preferred in applications where safety is of foremost concern, such as nuclear power plants and high-pressure thermal power plants. In the present study, optimum operating conditions based on the maximum heat transfer rate in NCLs have been obtained for subcritical as well as supercritical fluids. In recent years, there is a growing interest in the use of carbon dioxide (CO2) as loop fluid in NCLs for a variety of heat transfer applications due to its excellent thermophysical environmentally benign properties. In the present study, three-dimensional (3D) computational fluid dynamics (CFD) analysis of a CO2-based NCL with isothermal source and sink has been carried out. Results show that the heat transfer rate is much higher in the case of supercritical phase (if operated near pseudocritical region) than the subcritical phase. In the subcritical option, higher heat transfer rate is obtained in the case of liquid operated near saturation condition. Correlations for optimum operating condition are obtained for a supercritical CO2-based NCL in terms of reduced temperature and reduced pressure so that they can be employed for a wide variety of fluids operating in supercritical region. Correlations are also validated with different loop fluids. These results are expected to help design superior optimal NCLs for critical applications. © 2016 by ASME.Item Transient analysis of subcritical/supercritical carbon dioxide based natural circulation loop with end heat exchangers: experimental study(Springer Verlag service@springer.de, 2017) Yadav, A.K.; Ramgopal, M.; Bhattacharyya, S.Carbon dioxide (CO2) based natural circulation loops (NCLs) has gained attention due to its compactness with higher heat transfer rate. In the present study, experimental investigations have been carried out to capture the transient behaviour of a CO2 based NCL operating under subcritical as well as supercritical conditions. Water is used as the external fluid in cold and hot heat exchangers. Results are obtained for various inlet temperatures (323–353 K) of water in the hot heat exchanger and a fixed inlet temperature (305 K) of cooling water in the cold heat exchanger. Effect of loop operating pressure (50–90 bar) on system performance is also investigated. Effect of loop tilt in two different planes (XY and YZ) is also studied in terms of transient as well as steady state behaviour of the loop. Results show that the time required to attain steady state decreases as operating pressure of the loop increases. It is also observed that the change in temperature of loop fluid (CO2) across hot or cold heat exchanger decreases as operating pressure increases. © 2017, Springer-Verlag Berlin Heidelberg.Item A combined ANN-GA and experimental based technique for the estimation of the unknown heat flux for a conjugate heat transfer problem(Springer Verlag service@springer.de, 2018) Kumar, M.K.; Vishweshwara, P.S.; Gnanasekaran, N.; Balaji, C.The major objectives in the design of thermal systems are obtaining the information about thermophysical, transport and boundary properties. The main purpose of this paper is to estimate the unknown heat flux at the surface of a solid body. A constant area mild steel fin is considered and the base is subjected to constant heat flux. During heating, natural convection heat transfer occurs from the fin to ambient. The direct solution, which is the forward problem, is developed as a conjugate heat transfer problem from the fin and the steady state temperature distribution is recorded for any assumed heat flux. In order to model the natural convection heat transfer from the fin, an extended domain is created near the fin geometry and air is specified as a fluid medium and Navier Stokes equation is solved by incorporating the Boussinesq approximation. The computational time involved in executing the forward model is then reduced by developing a neural network (NN) between heat flux values and temperatures based on back propagation algorithm. The conjugate heat transfer NN model is now coupled with Genetic algorithm (GA) for the solution of the inverse problem. Initially, GA is applied to the pure surrogate data, the results are then used as input to the Levenberg- Marquardt method and such hybridization is proven to result in accurate estimation of the unknown heat flux. The hybrid method is then applied for the experimental temperature to estimate the unknown heat flux. A satisfactory agreement between the estimated and actual heat flux is achieved by incorporating the hybrid method. © 2018, Springer-Verlag GmbH Germany, part of Springer Nature.Item Study of adiabatic obstacles on natural convection in a square cavity using lattice boltzmann method(American Society of Mechanical Engineers (ASME) infocentral@asme.org, 2019) Karki, P.; Yadav, A.K.; Arumuga Perumal, D.A.This study involves the effect of adiabatic obstacles on twodimensional natural convection in a square enclosure using lattice Boltzmann method (LBM). The enclosure embodies squareshaped adiabatic obstacles with one, two, and four in number. The single obstacle in cavity is centrally placed, whereas for other two configurations, a different arrangement has been made such that the core fluid zone is not hampered. The four boundaries of the cavity considered here consist of two adiabatic horizontal walls and two differentially heated vertical walls. The current study covers the range of Rayleigh number (10 3 ? Ra ? 10 6 ) and a fixed Prandtl number of 0.71 for all cases. The effect of size of obstacle is studied in detail for single obstacle. It is found that the average heat transfer along the hot wall increases with the increase in size of obstacle until it reaches an optimum value and then with further increase in size, the heat transfer rate deteriorates. Study is carried out to delineate the comparison between the presences of obstacle in and out of the conduction dominant zone in the cavity. The number of obstacles (two and four) outside of this core zone shows that heat transfer decreases despite the obstacle being adiabatic in nature. © 2019 by ASME.Item Comparative computational appraisal of supercritical CO2-based natural circulation loop: effect of heat-exchanger and isothermal wall(Springer Science and Business Media B.V., 2020) Thimmaiah, S.; Wahidi, T.; Yadav, A.; Mahalingam, A.Natural circulation loop (NCL) is a geometrically simple heat transfer device in which fluid flow occurs due to density gradient of loop fluid, induced by the temperature difference between the source and the sink. NCL has an inherent problem of instability caused by the combined effect of buoyancy, friction and inertia forces at varying operating conditions, and hence it requires an elegant solution of instability. The primary objective of the present work is to do a comparative study on the dynamic performance between two different configurations of NCL based on supercritical CO2, i.e. (i) NCL with isothermal heater and a cold heat-exchanger (ISO-CHX), and (ii) NCL with hot and cold heat-exchangers (HHX-CHX). To explore these NCLs, two-dimensional transient computational fluid dynamics studies have been carried out on the stability of supercritical CO2-based natural circulation loop. Results are obtained for different operating pressures and temperatures in the form of mass flow rate and velocity variation with respect to time. Results show the higher instabilities in both side heat-exchanger loop than an isothermal heater with heat-exchanger loop. At a lower rate of heat input at source in the HHX-CHX loop, the mass flow is bidirectional, whereas it is unidirectional in the ISO-CHX loop at all level of heat input. It is also observed that as pressure increases, flow instability also increases. Obtained results are validated with the published experimental and numerical data and found in good agreement. © 2020, Akadémiai Kiadó, Budapest, Hungary.