Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
12 results
Search Results
Item Processing of cenosphere/HDPE syntactic foams using an industrial scale polymer injection molding machine(Elsevier Ltd, 2016) Bharath Kumar, B.R.; Doddamani, M.R.; Zeltmann, S.E.; Gupta, N.; Ramesh, M.R.; Ramakrishna, S.Rapid production of high quality components is the key to cost reduction in industrial applications. The present work is the first attempt of manufacturing syntactic foams, hollow particle filled lightweight composites, using an industrial scale injection molding machine. High density polyethylene (HDPE) is used as the matrix material and fly ash cenospheres are used as the filler. Development of syntactic foams with cenospheres serves dual purpose of beneficial utilization of industrial waste fly ash and reduction in the cost of the component. The pressure and temperature used in the injection molding process are optimized to minimize fracture of cenospheres and obtain complete mixing of cenospheres with HDPE. The optimized parameters are used for manufacturing syntactic foams with 20, 40 and 60 wt.% cenospheres. With increasing cenosphere content, density and strength reduce and modulus increases. Surface modification of constituents results in rise in strength with increasing filler content. A theoretical model based on a differential scheme is used to estimate the properties of cenospheres by conducting parametric studies because of inherent difficulties in direct measurement of cenosphere properties. The potential for using the optimized injection molding process is demonstrated by casting several industrial components. © 2015 Elsevier Ltd.Item Prediction of strain rate sensitivity of high density polyethylene using integral transform of dynamic mechanical analysis data(Elsevier Ltd, 2016) Zeltmann, S.E.; Bharath Kumar, B.R.; Doddamani, M.R.; Gupta, N.Recent interest in understanding the effect of strain rate on mechanical properties has motivated this study to develop a correlation between frequency domain dynamic mechanical analysis (DMA) results and elastic modulus values that are obtained from a separate set of elaborate tensile tests conducted over a wide range of strain rates. Using the time-temperature superposition principle and the integral relations of viscoelasticity, the DMA results are converted into a time-domain relaxation function in order to predict the strain-rate dependent modulus. The transformation technique is validated with experimental results for high density polyethylene (HDPE) resin and is found to be accurate over a wide range of strain rates. Cross correlation between DMA results and tensile test results over a wide range of strain rates can help in substantially reducing the requirement for tests that are needed to characterize the material behavior with respect to strain rates, temperature and loading frequency. © 2016 Elsevier LtdItem Neutron radiation shielding properties of polymer incorporated self compacting concrete mixes(Elsevier Ltd, 2017) Malkapur, S.M.; Divakar, L.; Narasimhan, M.C.; Karkera, N.B.; Goverdhan, P.; Sathian, V.; Prasad, N.K.In this work, the neutron radiation shielding characteristics of a class of novel polymer-incorporated self-compacting concrete (PISCC) mixes are evaluated. Pulverized high density polyethylene (HDPE) material was used, at three different reference volumes, as a partial replacement to river sand in conventional concrete mixes. By such partial replacement of sand with polymer, additional hydrogen contents are incorporated in these concrete mixes and their effect on the neutron radiation shielding properties are studied. It has been observed from the initial set of experiments that there is a definite trend of reductions in the neutron flux and dose transmission factor values in these PISCC mixes vis-à-vis ordinary concrete mix. Also, the fact that quite similar enhanced shielding results are recorded even when reprocessed HDPE material is used in lieu of the virgin HDPE attracts further attention. © 2017 Elsevier LtdItem Fresh and hardened properties of polymer incorporated self compacting concrete mixes for neutron radiation shielding(Elsevier Ltd, 2017) Malkapur, S.M.; Divakar, L.; Narasimhan, M.C.; Karkera, N.B.; Goverdhan, P.; Sathian, V.; Prasad, N.K.Several works in the past have reported that the hydrogen content in the hydrated concrete plays an important role in shielding the neutron radiation; higher the hydrogen content, better is the neutron radiation shielding. In this study, pulverised high density polyethylene (HDPE) material is used as an additional source of hydrogen within concrete to develop a novel class of Polymer-Incorporated Self-Compacting Concrete (PISCC) mixes for enhanced neutron radiation shielding. The HDPE material was incorporated as a partial replacement to river sand. It is found that the PISCC mixes have satisfactory fresh and hardened properties and enhanced neutron radiation shielding properties. © 2017 Elsevier LtdItem Additive Manufacturing of Syntactic Foams: Part 2: Specimen Printing and Mechanical Property Characterization(Minerals, Metals and Materials Society 184 Thorn Hill Road Warrendale PA 15086, 2018) Singh, A.K.; Saltonstall, B.; Patil, B.; Hoffmann, N.; Doddamani, M.; Gupta, N.High-density polyethylene (HDPE) and its fly ash cenosphere-filled syntactic foam filaments have been recently developed. These filaments are used for three-dimensional (3D) printing using a commercial printer. The developed syntactic foam filament (HDPE40) contains 40 wt.% cenospheres in the HDPE matrix. Printing parameters for HDPE and HDPE40 were optimized for use in widely available commercial printers, and specimens were three-dimensionally (3D) printed for tensile testing at strain rate of 10?3 s?1. Process optimization resulted in smooth operation of the 3D printer without nozzle clogging or cenosphere fracture during the printing process. Characterization results revealed that the tensile modulus values of 3D-printed HDPE and HDPE40 specimens were higher than those of injection-molded specimens, while the tensile strength was comparable, but the fracture strain and density were lower. © 2018, The Minerals, Metals & Materials Society.Item Additive Manufacturing of Syntactic Foams: Part 1: Development, Properties, and Recycling Potential of Filaments(Minerals, Metals and Materials Society 184 Thorn Hill Road Warrendale PA 15086, 2018) Singh, A.K.; Patil, B.; Hoffmann, N.; Saltonstall, B.; Doddamani, M.; Gupta, N.This work focuses on developing filaments of high-density polyethylene (HDPE) and their hollow particle-filled syntactic foams for commercial three-dimensional (3D) printers based on fused filament fabrication technology. Hollow fly-ash cenospheres were blended by 40 wt.% in a HDPE matrix to produce syntactic foam (HDPE40) filaments. Further, the recycling potential was studied by pelletizing the filaments again to extrude twice (2×) and three times (3×). The filaments were tensile tested at 10?4 s?1, 10?3 s?1, and 10?2 s?1 strain rates. HDPE40 filaments show an increasing trend in modulus and strength with the strain rate. Higher density and modulus were noticed for 2× filaments compared to 1× filaments because of the crushing of some cenospheres in the extrusion cycle. However, 2× and 3× filament densities are nearly the same, showing potential for recycling them. The filaments show better properties than the same materials processed by conventional injection molding. Micro-CT scans show a uniform dispersion of cenospheres in all filaments. © 2018, The Minerals, Metals & Materials Society.Item Eco-friendly lightweight filament synthesis and mechanical characterization of additively manufactured closed cell foams(Elsevier Ltd, 2019) Patil, B.; Bharath Kumar, B.R.; Bontha, S.; Balla, V.K.; Powar, S.; Hemanth Kumar, V.H.; Suresha, S.N.; Doddamani, M.Environmentally pollutant fly ash cenospheres (hollow microballoons) are utilized with most widely consumed, relatively expensive high density polyethylene (HDPE) for developing lightweight eco-friendly filament for 3D printing of closed cell foams. Cenospheres (20, 40 and 60 by volume %) are blended with HDPE and subsequently extruded in filament to be used for 3D printing. Cenosphere/HDPE blends are studied for melt flow index (MFI) and rheological properties. MFI decreases with cenospheres addition. Complex viscosity, storage and loss modulus increase with filler loading. DSC results on the filament and printed samples reveal increasing crystallization temperature and decreasing crystallinity % with no appreciable change in peak melting temperature. Cooling rate variations exhibit crystallinity differences between the filament and the prints. CTE decreases with increasing cenosphere content resulting in lower thermal stresses and under diffusion of raster leading to non-warped prints. Micrography on freeze fractured filament and prints show cenospheres uniform distribution in HDPE. Intact cenospheres lower the foam density making it lightweight. Tensile tests are carried out on filaments and printed samples while flexural properties are investigated for 3D prints. Cenospheres addition resulted in improved tensile modulus and decreased filament strength. Tensile and flexural modulus of printed foams increases with filler content. Results are also compared with injection molded samples. Printed foams registered comparable tensile strength. Specific tensile modulus is noted to be increased with cenospheres loading implying weight saving potential of 3D printed foams. Property map reveals printed foams advantage over other fillers and HDPE composites synthesized through injection and compression molding. © 2019 Elsevier LtdItem Compressive behavior of fly ash based 3D printed syntactic foam composite(Elsevier B.V., 2019) Patil, B.; Bharath Kumar, B.R.; Doddamani, M.Syntactic foams are widely used in damage tolerance and low-density applications. In present work compressive behavior of 3D printed three-phase syntactic foams under quasi-static strain rates (0.001, 0.01 and 0.1 s?1) are investigated. Extruded filaments of High density polyethylene (HDPE) with environmentally pollutant fly ash cenospheres (0, 20, 40 and 60 vol%) are used for 3D printing. Micrography reveal that syntactic foam filament and 3D printed samples are three phase systems comprising matrix, cenosphere and porosity. Matrix porosity of about 7% makes these foams lightweight and suitable for buoyant applications. The compressive properties are extracted from the stress-strain plots. It is observed that modulus and specific modulus increases with strain rate and cenosphere content. Specific compressive strength increases with strain rate and decrease with cenosphere content. © 2019 Elsevier B.V.Item Performance of Footing on Clay Bed Reinforced with Coir Cell Networks(American Society of Civil Engineers (ASCE) onlinejls@asce.org 1801 Alexander Bell DriveGEO Reston VA 20191 Alabama, 2020) Kolathayar, S.; Narasimhan, S.; Kamaludeen, R.; Sitharam, T.G.Geocells are three-dimensional polymeric hexagonal pockets that provide lateral confinement to the soil, thereby increasing the bearing capacity of the soil bed. This paper briefly reviews past studies on geocell reinforcement of soil and presents a new product, cells made out of natural coir fiber, as an alternative to commercially available high-density polyethylene (HDPE) geocells. A series of model plate load tests were conducted on unreinforced soil and on soil reinforced with coir geocells to understand the soil reinforcement mechanism. It was observed that with the introduction of coir geocells, the load-bearing capacity of the soil bed increased up to three times and a significant reduction in the settlement was observed in the underlying weak soil bed. The study also presents a comparative performance evaluation of the natural coir cell-reinforced soil with conventional HDPE geocell-reinforced soil. Further, this paper analytically demonstrates the influence of the lateral resistance effect and vertical load dispersion effect incorporated by coir cells in strengthening the soil bed. © 2020 American Society of Civil Engineers.Item Mechanical behaviour of additively manufactured bioactive glass/high density polyethylene composites(Elsevier Ltd, 2020) Jeyachandran, P.; Bontha, S.; Bodhak, S.; Balla, V.K.; Kundu, B.; Doddamani, M.Bioactive glass (BAG) is a well-known biomaterial that can form a strong bond with hard and soft tissues and can also aid in bone regeneration. In this study, BAG is added to a polymer to induce bioactivity and to realize fused filament fabrication (FFF) based printing of polymer composites for potential orthopaedic implant applications. BAG (5, 10, and 20 wt%) is melt compounded with high density polyethylene (HDPE) and subsequently extruded into feedstock filament for FFF-printing. Tensile tests on developed filaments reveal that they are stiff enough to resist forces exerted during the printing process. Micrography of printed HDPE/BAG reveals perfect diffusion of raster interface indicating proper selection of printing parameters. Micrography of freeze fractured prints shows the homogeneous distribution and good dispersion of filler across the matrix. The tensile, flexural, and compressive modulus of FFF-printed HDPE/BAG parts increases with filler addition. BAG addition to the HDPE matrix enhances flexural and compressive strength. The tensile and flexural behaviour of FFF-prints is comparable to injection molded counterparts. Property maps exhibit the merits of present study over the existing literature pertaining to desired bone properties and polymer composites used in biomedical applications. It is envisioned that the development of HDPE/BAG composites for FFF-printing can lead to possible orthopaedic implants and scaffolds to mimic the bone properties in customised anatomical sites or injuries. © 2020 Elsevier Ltd