Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
17 results
Search Results
Item An experimental investigation to determine the properties of fly ash based geopolymers as per indian standards(Springer, 2019) Saha, S.; C, C.Production of ordinary Portland cement requires huge quantity of natural resources and also releases huge quantity of carbon dioxide into the atmosphere. Research efforts have been continuing to establish geopolymer as an alternative cementitious material for the replacement of ordinary Portland cement. This paper presents the study to find out the properties of fly ash based geopolymer paste and 28 days compressive strength of geopolymer mortar. Standard consistency, setting time of geopolymer paste has been determined using vicat’s apparatus (according to Indian Standards), which is followed for cement paste, varying the concentration of sodium hydroxide solution from 6 to 16 M. Results indicate higher standard consistency, more time required for setting for fly ash based geopolymer than that of cement paste. Compressive strength of the geopolymer paste and mortar 17 specimens increases with the increase of the concentration of sodium hydroxide solution and decrease beyond 14 M. © 2019, Springer Nature Singapore Pte Ltd.Item Characterization of Mechanical and Microstructural Properties of FA and GGBS-Based Geopolymer Mortar Cured in Ambient Condition(Springer, 2021) Prasanna, K.M.; Tamboli, S.; Das, B.B.Fly ash-based geopolymer mortars require heat curing to achieve its properties, which limits its practical application at ambient conditions. The present study was aimed to accomplish the need for application of fly ash-based geopolymers for practical viability without any heat curing by inclusion of ground-granulated blast furnace slag (GGBS). The results revealed that inclusion of GGBS as a partial replacement to fly ash (FA) in geopolymer mortar, which is cured in ambient curing condition, can be able to achieve required setting time and compressive strength. Amalgamation of GGBS with class FA as binder in geopolymerization lend a hand to attain compressive strength as well as setting time which is analogous to ordinary Portland cement (OPC). Microstructural properties were studied using scanning electron microscopy. © 2021, Springer Nature Singapore Pte Ltd.Item Soil Stabilization Using Spent Coffee Residue with Geopolymerization Technique(Springer Science and Business Media Deutschland GmbH, 2024) Lalfakzual; I Talkeri, H.T.; Raghuram, K.C.; Chiranjeevi, K.Spent coffee residue contains a significant amount of biodegradable material and is extremely organic. This study aims to assess the feasibility of blending the soil with spent coffee residue and industrial by-products such as fly ash and slag through a sustainable approach using the geopolymerization technique. Geopolymerization was induced using fly ash (FA) and slag as precursors with sodium hydroxide and sodium silicate as alkaline activators. Modified compaction was investigated to determine the optimum moisture content and bearing strength of the mixes produced. The Taguchi's L-9 orthogonal array served as the foundation for the formulation of all nine geopolymer mixes created herein. In an initial calibration phase, the durability and unconfined compressive strength (UCS) characteristics of a set of nine mixes were utilized for performance evaluation. On the basis of these findings, strength and durability prediction equations were developed. In the prediction phase, the accuracy of the developed model is evaluated with actual test results from trials on the nine mixes. Partial replacement of slag by 20 and 30% with the desired sodium oxide content range between 3 and 5% complied with the standard for subgrade material. Test results indicate stabilized coffee residue might be used as subgrade material rather than being dumped in landfills. © The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd. 2024.Item Enhancement of the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag(Elsevier Ltd, 2017) Saha, S.; C, C.Research efforts have been made continuously to establish fly ash based geopolymer as an alternative binder material for the production of fresh concrete because production of Ordinary Portland Cement degrades the environment by huge emissions of carbon-di-oxide and also by consuming lot of natural resources. But most of the study reveals, fly ash based geopolymer paste needs more time to get set when it is cured at ambient temperature. As a result, it is quite impractical to use fly ash based geopolymer paste as an alternative to Ordinary Portland Cement in faster construction. In this study, an effort has been made to enhance the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag at various percentage levels. Microstructure of the geopolymer paste is studied using Scanning Electron Microscopy. Result of this investigation shows that significant improvement on setting time and compressive strength can be obtained by adding ground granulated blast furnace slag in the mixes. © 2017 Elsevier LtdItem Determination of optimized geopolymerization factors on the properties of pelletized fly ash aggregates(Elsevier Ltd, 2018) Shivaprasad, K.N.; Das, B.B.This research investigates the effect of geopolymerization factors on the pelletization in the production of artificial fly ash aggregates. The proportion of pelletized fly ash aggregate mixes was designed through Taguchi's L9 orthogonal array. The properties of the aggregates produced from the optimal mixes were characterized according to the standard specifications. The effect of geopolymerization factors such as Na2O content, water content, and curing regime on the properties of the pelletized fly ash geopolymer aggregates was determined through response indices at the age of 14, 28 and 56 days. In addition, Grey relation based analysis was performed to identify the most critical parameter for optimization among three geopolymerization factors selected in this investigation, for the production of pelletized fly ash geopolymer aggregates. It is observed from the response indices and Grey relation results that the impact value of the aggregates and crushing strength of individual pellets is governed by heat curing and high water content at the age of 14 and 28 days. However, at the age of 56 days these response indices are significantly governed by the solution curing and high water content. It was also noted that the minimum Na2O content of 3.5–4.5% is adequate for the production of pelletized fly ash aggregates. © 2017 Elsevier LtdItem Influence of fineness of fly ash on compressive strength and microstructure of bottom ash admixed geopolymer mortar(Associated Cement Companies Ltd., 2018) Shivaprasad, K.N.; Das, B.B.; Renjith, R.Investigations were conducted to find out the suitability of bottom ash as a possible replacement to fine aggregates in geopolymer mortar. Experimental work was done to study the influence of fineness of fly ash (with three levels of Blaine's fineness, 2043 cm2/g, 2602 cm2/g and 3113 cm2/g on compressive strength and microstructure development of fly ash based geopolymer mortar with natural river sand and bottom ash as fine aggregates. three different water to solids ratios of 0.246, 0.349, and 0.443 were chosen for this study and the curing of the specimens was at ambient temperature (28 ± 3°c). compressive strength development for all eighteen mortar mixes was measured at 7, 14, 28 and 56 days. Further, the effect of fineness of fly ash on degree of polymerization, microstructure and properties of geopolymers was studied using Fourier transform Infrared Spectroscopy (FtIR) and Scanning Electron Microscopy (SEM). It was observed from the compressive strength of the geopolymer mortar that the degree of polymerization is gradual for both types of mortar. there is a continuous increase in the development of compressive strength noticed till the age of 56 days for both types of mortar, sand as well as bottom ash admixed. However, the increment of compressive strength for bottom ash found to be significantly less as compared to natural sand. Improvement in compressive strength due to fineness of fly ash were characterised by SEM and FtIR and it is revealed that with increase in fineness levels, the microstructure significantly enhanced the characteristics of geopolymer mortar. © 2018 Associated Cement Companies Ltd.. All rights reserved.Item Investigation on the potential use of recycled fine aggregate to produce geopolymer mortar mix(ASTM International, 2019) Saha, S.; C, C.The utilization of construction and demolition waste (C&DW) partially or fully for various purposes in construction industries is one of the most significant solutions to overcome the scarcity of raw materials and disturbances of the environmental system. On the other hand, geopolymer is being tried to be established as an alternative sustainable binder material for ordinary portland cement. In the present study, with the thought of promoting of sustainability, an attempt has been made to use concrete wastes as recycled fine aggregate (RFA) partially to produce fly ash (FA)-based geopolymer mortar. The workability, water absorption, compressive strength at 3, 7, 28, and 56 days, volume change behavior, and chloride permeability of the produced FA-based geopolymer mortar were determined. The effects of RFA, the ratio of alkali liquid (AL) to FA, and different curing regimes on these properties of mortar mix also discussed. The morphology and microstructures of the samples taken from the mortar mix, which were observed having the highest strength under different curing regimes, were studied using scanning electron microscopy (SEM). The experimental results indicate lower workability, higher water absorption capacity, and higher drying shrinkage of geopolymer mortar mix that has more RFA content in the mix, but the compressive strength of the geopolymer mortar mix started decreasing after a certain percentage of RFA content in the mix. Utilization of that certain percentage of RFA will help us to minimize the consumption of natural fine aggregates and reduce the disturbances generated by unorganized dumping of C&DW. © 2019 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.Item Volume change characteristics of eco-friendly mortar mixes produced with geopolymeric binder and recycled fine aggregate(ASTM International, 2020) Saha, S.; Shaik, N.; C, C.The production of geopolymer mortar using recycled fine aggregate (RFA) generated from concrete waste has significant potential to be a sustainable construction material. In this article, the volume change properties of the produced geopolymer mortar mixes are studied in terms of drying shrinkage up to the age of 180 days and reported as the percentage increase with respect to the shrinkage value of 3 days. The influence of RFA content, alkaline liquid (AL) in terms of the concentration of sodium hydroxide (SH) solution, the ratio of sodium silicate (SS) solution to SH solution, and the ratio of AL to fly ash (FA) were investigated on the drying shrinkage properties of the geopolymer mortar mixes. All the cast specimens were cured at 80°C for 24 hours. Higher drying shrinkage values were observed for the mortar mixes produced with higher RFA content, AL/FA, SS/SH ratio, and lower concentration of SH solution. Scanning electron microscope images were studied for the samples taken from the geopolymer mixes showing lower drying shrinkage values to understand the microstructure. © 2019 by ASTM International.Item Performance of eco-friendly mortar mixes against aggressive environments(Techno-Press info@techno-press.com, 2020) Saha, S.; C, C.; Gupta, P.Past research efforts already established geopolymer as an environment-friendly alternative binder system for ordinary Portland cement (OPC) and recycled aggregate is also one of the promising alternative for natural aggregates. In this study, an effort was made to produce eco-friendly mortar mixes using geopolymer as binder and recycled fine aggregate (RFA) partially and study the resistance ability of these mortar mixes against the aggressive environments. To form the geopolymer binder, 70% fly ash, 30% ground granulated blast furnace slag (GGBS) and alkaline solution comprising of sodium silicate solution and 14M sodium hydroxide solution with a ratio of 1.5 were used. The ratio of alkaline liquid to binder (AL/B) was also considered as 0.4 and 0.6. In order to determine the resistance ability against aggressive environmental conditions, acid attack test, sulphate attack test and rapid chloride permeability test were conducted. Change in mass, change in compressive strength of the specimens after the immersion in acid/sulphate solution for a period of 28, 56, 90 and 120 days has been presented and discussed in this study. Results indicated that the incorporation of RFA leads to the reduction in compressive strength. Even though strength reduction was observed, eco-friendly mortar mixes containing geopolymer as binder and RFA as fine aggregate performed better when it was produced with AL/B ratio of 0.6. © 2020 Techno-Press, Ltd.Item Strength and shrinkage properties of heat-cured fly ash-based geopolymer mortars containing fine recycled concrete aggregate(ASTM International, 2020) Saha, S.; C, C.Geopolymer has obtained significant importance as an alternative eco-friendly binder material for ordinary portland cement (OPC) as it can be produced from the reaction between the industrial by-product materials rich in alumina, silica, and alkaline solutions. Therefore, usage of geopolymer effectively in the construction industry will help to reduce the consumption of a huge quantity of natural resources for the energy processes required for the production of OPC. It is also one of important solution to control carbon dioxides emission by the usage of OPC. On the other hand, using construction and demolition waste (C&DW) as the source of recycled aggregates in construction industry helps to reduce the huge consumption of natural aggregates and protect the environment from the disturbances caused by the unorganized dumping of C&DW. In this study, an attempt has been madeto produce fly ash (FA)-based geopolymer mortar mixes using C&DW effectively as fine aggregates partially. The effects of recycled fine aggregates (RFA), the ratio of alkaline liquid (AL) to FA, and duration of heat curing on the properties of the produced geo-polymer mortar mixes have been discussed in this article. To determine the influence of RFA on the strength and volume change behavior of mixes, natural fine aggregates were replaced by RFA at 0, 10, 20, 30, 40, and 50 % by mass. The AL/FA ratio was adopted as 0.4 and 0.6. Higher compressive strength was observed for most of the mortar mixes having RFA up to 20 %, and higher drying shrinkage value was found for the mixes with higher RFA content. Scanning electron microscopy (SEM) images were also studied for knowledge about the signature of the formed structures in the mortar mixes, which were observed having higher strength. © © 2019 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.