Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
49 results
Search Results
Item Static analysis of functionally graded beams using higher order shear deformation theory(2008) Kadoli, R.; Akhtar, K.; Ganesan, N.Displacement field based on higher order shear deformation theory is implemented to study the static behavior of functionally graded metal-ceramic (FGM) beams under ambient temperature. FGM beams with variation of volume fraction of metal or ceramic based on power law exponent are considered. Using the principle of stationary potential energy, the finite element form of static equilibrium equation for FGM beam is presented. Two stiffness matrices are thus derived so that one among them will reflect the influence of rotation of the normal and the other shear rotation. Numerical results on the transverse deflection, axial and shear stresses in a moderately thick FGM beam under uniform distributed load for clamped-clamped and simply supported boundary conditions are discussed in depth. The effect of power law exponent for various combination of metal-ceramic FGM beam on the deflection and stresses are also commented. The studies reveal that, depending on whether the loading is on the ceramic rich face or metal rich face of the beam, the static deflection and the static stresses in the beam do not remain the same. © 2007 Elsevier Inc. All rights reserved.Item Comparative analysis of steady state heat transfer in a TBC and functionally graded air cooled gas turbine blade(2010) Coomar, N.; Kadoli, R.Internal cooling passages and thermal barrier coatings (TBCs) are presently used to control metal temperatures in gas turbine blades. Functionally graded materials (FGMs), which are typically mixtures of ceramic and metal, have been proposed for use in turbine blades because they possess smooth property gradients thereby rendering them more durable under thermal loads. In the present work, a functionally graded model of an air-cooled turbine blade with airfoil geometry conforming to the NACA0012 is developed which is then used in a finite element algorithm to obtain a non-linear steady state solution to the heat equation for the blade under convection and radiation boundary conditions. The effects of external gas temperature, coolant temperature, surface emissivity changes and different average ceramic/metal content of the blade on the temperature distributions are examined. Simulations are also carried out to compare cooling effectiveness of functionally graded blades with that of blades having TBC. The results highlight the effect of including radiation in the simulation and also indicate that external gas temperature influences the blade heat transfer more strongly. It is also seen that graded blades with about 70% ceramic content can deliver better cooling effectiveness than conventional blades with TBC. © 2010 Indian Academy of Sciences.Item Behavior of sandwich beams with functionally graded rubber core in three point bending(2011) Doddamani, M.R.; Kulkarni, S.M.; KishoreThe three-point bending behavior of sandwich beams made up of jute epoxy skins and piecewise linear functionally graded (FG) rubber core reinforced with fly ash filler is investigated. This work studies the influence of the parameters such as weight fraction of fly ash, core to thickness ratio, and orientation of jute on specific bending modulus and strength. The load displacement response of the sandwich is traced to evaluate the specific modulus and strength. FG core samples are prepared by using conventional casting technique and sandwich by hand layup. Presence of gradation is quantified experimentally. Results of bending test indicate that specific modulus and strength are primarily governed by filler content and core to sandwich thickness ratio. FG sandwiches with different gradation configurations (uniform, linear, and piecewise linear) are modeled using finite element analysis (ANSYS 5.4) to evaluate specific strength which is subsequently compared with the experimental results and the best gradation configuration is presented. © 2011 Society of Plastics Engineers.Item Instrumented ballistic performance of jute/epoxy sandwich with functionally graded rubber core(Inderscience Publishers, 2012) Doddamani, M.R.; Kulkarni, S.M.The qualitative analysis of instrumented ballistic impact for jute-epoxy sandwiches with fly ash reinforced functionally graded (FG) flexible, compliant rubber core is presented. An attempt is made to study the influence of fly ash weight fraction, jute orientation and core to total thickness (C/H) of sandwich on ballistic performance. Experiments are designed based upon L9 orthogonal array. Analysis of variance (ANOVA) is performed on recorded data to investigate the influence of parameters on ballistic response. An optimal parameter combination is determined leading to higher energy absorption and lower energy required for skin pullout by the bullet. A correlation derived from the results of Taguchi experimental design is proposed as a predictive equation for estimation of energy absorption of sandwiches. Furthermore, for arresting bullet optimum stack thickness of sandwich configuration is presented. Finally, the potential benefits for using such materials as a replacement for sand bags in guarding posts is highlighted. Copyright © 2012 Inderscience Enterprises Ltd.Item Response of fly ash-reinforced functionally graded rubber composites subjected to mechanical loading(2012) Doddamani, M.R.; Kulkarni, S.M.A novel approach to estimate the Young's modulus of a functionally graded rubber composite (FGRC) from the damping ratio is demonstrated with the examples of unreinforced and fly ash-reinforced materials. FGRC coupons were prepared using the conventional casting technique. The occurrence of gradation in the specimens was attributed to the variable density of particles present in the fly ash, settling at different depths. The technique of free vibrations was used for experimentation. The damping response of the FGRC specimens was studied. The results obtained from the experiments showed that, with growing filler weight fraction, the Young's modulus of the composite increased. The empirical model developed to predict the magnitude of the modulus turned out to be in good agreement with experimental data. © 2012 Springer Science+Business Media, Inc.Item Compressive properties of sandwiches with functionally graded rubber core and jute-epoxy skins(2013) Doddamani, M.R.; Kulkarni, S.The compressive behaviour of a new class of sandwich composite made up of jute fiber reinforced epoxy skins and piece-wise linear fly ash reinforced functionally graded (FG) rubber core is investigated in flat-wise mode. FG samples are prepared using conventional casting techniéue. Presence of gradation is éuantified physically by weight method. This paper addresses the effect of weight fraction of fly ash, core to thickness ratio (C/H) and orientation of jute on specific compressive modulus and strength. In each trial five replicates are tested with lower amount of fly ash below the upper skin of sandwich (rubber-up). Results of experimentation are subjected to statistical analysis of variance (ANOVA) to find the influential factor governing the compressive behaviour. Furthermore piece-wise linear gradation is modeled in finite element and strength values are compared with experimental results. Sandwich sample with fly ash content of 40%, C/H of 0.4 and orientations of 30?/60? registered better performance. Specific strength is observed to increase upto 30% filler content followed by stabilization. Finite element results for strength match very well with experimental ones.Item Compressive and flexural properties of functionally graded fly ash cenosphere-epoxy resin syntactic foams(John Wiley and Sons Inc, 2015) Doddamani, M.; Kishore; Shunmugasamy, V.C.; Gupta, N.; Vijayakumar, H.B.The present study focuses on developing functionally graded syntactic foams (FGSFs) based on a layered co-curing technique. The FGSFs were characterized for compressive and flexural properties and compared with plain syntactic foams. The results showed that the specific compressive modulus was 3-67% higher in FGSFs compared to plain syntactic foams. FGSF exhibited 5-34% and 34-87% higher specific modulus and strength, respectively in flexural mode. The microscopic examinations of comparative responses of the filler and matrix to deformation suggest that the failure is dominated by the matrix. The gradient in the composition of syntactic foams helps in effectively distributing the stress throughout the microstructure and results in improved mechanical performance of syntactic foams. From the microscopy studies, it is evident that, the failure mechanism in the FGSF under flexural loading is governed by a crack that initiated on the tensile side of the specimen and propagated through the thickness to cause complete fracture. The microscopic observations further clearly demonstrate the existence of seamless interfaces between the layers and a clear difference in the cenosphere concentration across the interface, affirming the gradation in the prepared samples. The results show that appropriate compositions of FGSFs can be selected to develop materials with improved mechanical performance. © 2014 Society of Plastics Engineers.Item Static studies of stepped functionally graded magneto-electro-elastic beam subjected to different thermal loads(Elsevier Ltd, 2017) Mahesh, M.; Kattimani, S.C.In this article, a three dimensional finite element (FE) formulation for a multilayered magneto-electro-elastic (MEE) beam in thermal environment is presented. The equilibrium equations of the system are attained using the principle of total potential energy and linear coupled constitutive equations of MEE material. The corresponding FE equations are derived and the numerical evaluation of stepped functionally graded (SFG) MEE beam is carried out. The influence of various in-plane and through thickness temperature distributions on the direct quantities (displacements and potentials) and derived quantities (stresses, electric displacement and magnetic flux density), across the thickness of SFG-MEE cantilever beam is analyzed. In addition, an attempt has been made to investigate the effect of stacking sequence, thermo-magnetic and thermo-electric coupling on the direct quantities of the SFG-MEE beam. Further, a comparative study is made to evaluate the variations of displacements, potentials, electric displacements, magnetic flux density and stresses at different regions of the beam. It is expected that the results presented in this article may be useful in the design and analysis of MEE smart structures and sensor applications. © 2016 Elsevier LtdItem Thermal induced motion of functionally graded beams subjected to surface heating(Ain Shams University, 2018) Malik, P.; Kadoli, R.Thin beam of the functionally graded (FG) type subjected to a step heat input on one surface and insulated or exposed to convective heat loss on the opposite surface is under consideration for the evaluation of thermal induced motion. The dynamic displacement and dynamic thermal moment of the beam are analysed when the temperature gradient is independent of the beam displacement. The power law index dictates the metal–ceramic distribution across thickness of the beam and its effect on the thermal vibration of the beam is examined. The article discusses, in depth, the influence of various factors such as length to thickness ratio of beam, heat transfer boundary conditions, physical boundary conditions, and metal–ceramic combination on the thermal oscillations of FG beam. It is found that attenuation of the amplitude of static thermal deflection and superimposed thermal oscillations is a strong function of the metal–ceramic combination for the FG beam. © 2015 Faculty of Engineering, Ain Shams UniversityItem Influence of coupled fields on free vibration and static behavior of functionally graded magneto-electro-thermo-elastic plate(SAGE Publications Ltd info@sagepub.co.uk, 2018) Mahesh, M.; Sagar, P.J.; Kattimani, S.In this article, the influence of full coupling between thermal, elastic, magnetic, and electric fields on the natural frequency of functionally graded magneto-electro-thermo-elastic plates has been investigated using finite element methods. The contribution of overall coupling effect as well as individual elastic, piezoelectric, piezomagnetic, and thermal phases toward the stiffness of magneto-electro-thermo-elastic plates is evaluated. A finite element formulation is derived using Hamilton’s principle and coupled constitutive equations of magneto-electro-thermo-elastic material. Based on the first-order shear deformation theory, kinematics relations are established and the corresponding finite element model is developed. Furthermore, the static studies of magneto-electro-elastic plate have been carried out by reducing the fully coupled finite element formulation to partially coupled state. Particular attention has been paid to investigate the influence of thermal fields, electric fields, and magnetic fields on the behavior of magneto-electro-elastic plate. In addition, the effect of pyrocoupling on the magneto-electro-elastic plate has also been studied. Furthermore, the effect of geometrical parameters such as aspect ratio, length-to-thickness ratio, stacking sequence, and boundary conditions is studied in detail. The investigation may contribute significantly in enhancing the performance and applicability of functionally graded magneto-electro-thermo-elastic structures in the field of sensors and actuators. © 2017, © The Author(s) 2017.