Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
15 results
Search Results
Item Experimental Studies on the Effect of Varying Rates of Part-Cooled EGR in High Pressure Loop on an MPFI Engine Under Variable Speed Operation(Springer Science and Business Media Deutschland GmbH info@springer-sbm.com, 2021) Oommen, L.P.; Kumar, G.N.Researches in automobile sector around the globe are focused on meeting the currently proposed emission norms. Exhaust gas recirculation is one pre-treatment technique that has been found effective in enhancing the combustion and emission characteristics of IC engines and regulating the emission of nitrogen oxides. The present work analyses the effect produced by different rates of partially cooled EGR in a high pressure loop on a multi-cylinder MPFI gasoline engine. Three flow rates of EGR—12%, 18% and 24%—have been studied, and the impact produced on thermal efficiency, specific fuel consumption and emission of macropollutants of the test engine has been analysed under variable speed operation in comparison with normal operation of the engine without recirculation. The temperature of recirculated exhaust gas is so maintained as not to have a negative influence on the fuel consumption characteristics. A reduction in specific fuel consumption is observed which results in a marginal improvement of brake thermal efficiency alongside the advantage obtained in the emissions of the engine. The study proves that the advantages of EGR addition are limited to around 18% above to which the cyclic variations and misfires become predominant, deteriorating the performance and emissions of the test engine. © 2021, Springer Nature Singapore Pte Ltd.Item Effect of exhaust gas recirculation (EGR) on diesel engine using Simarouba glauca biodiesel blends(Regional Energy Resources Information Center (RERIC) enreric@ait.ac.th, 2015) Bedar, P.; Pandey, J.K.; Kumar, G.N.This article deals with the usage of non-edible Simarouba glauca (paradise) oil as a biodiesel for single cylinder diesel engine with application of exhaust gas recirculation (EGR) rates. Biodiesel blends B10, B20 with EGR rates of 10%, 15%, and 20% are used for different load conditions. Parameters like brake thermal efficiency (BTE), nitrogen oxides (NOx), carbon monoxide (CO), hydrocarbons (HC) and smoke opacity were evaluated from the experimental study. The results show that Simarouba glauca biodiesel usage decreases HC, CO and smoke emissions with slight increase of NOx, also an improvement in the performance was observed for B10 blend. EGR rates 10% and 15% are beneficiated in terms of performance and emission but negative trend is observed for 20% EGR rate. On the whole it is concluded that a better trade-off between NOx and other emissions is attained with simultaneous application of EGR (15%) and biodiesel blend (B10) without compromising engine performance.Item Performance and emission analysis of a single cylinder CI engine using Simarouba glauca biodiesel(Springer Heidelberg, 2017) Bedar, P.; Chitragar, P.R.; Shivaprasad, K.V.; Kumar, G.N.It is well known fact that diesel engines are commonly used for transportation and power generation due to their high efficiency, low fuel consumption and durability. On contrary these engines churn out harmful and hazardous emissions like particulate matter (PM) and nitrogen oxides (NOx). Recently Bio-origin renewable fuels have taken center stage of discussion because of their ability to replace depleting fossil fuels and capacity to reduce hazardous engine exhausts emissions when used in diesel engines. In the present experimental study Simarouba glauca biodiesel is used in a naturally aspirated four stroke single cylinder air cooled direct injection kirloskar DA10 engine. The main objective is to investigate the effect of biodiesel and exhaust gas recirculation (EGR) on the performance and emission characteristics of a CI engine at 180 bar fuel injection pressure (FIP) with standard injection timing. B20, B40 biodiesel blends with 10, 15 and 20% EGR ratios were used for the study to investigate brake thermal efficiency (BTE), carbon monoxide (CO), unburned hydrocarbons (UBHC), NOx, and smoke opacity. Reduction in CO, HC and smoke opacity is noticed with simarouba biodiesel fuel while increasing NOx compared to diesel. Application of EGR along with biodiesel resulted in simultaneous reduction of nitrogen oxides and smoke without affecting engine performance. It was found from experiment that B20 blend at 15% EGR shown superior performance characteristics compared to other conditions. © Springer India 2017.Item Combined effect of oxygen enrichment and exhaust gas recirculation on the performance and emissions of a diesel engine fueled with biofuel blends(Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2018) Dinesha, P.; Mohanan, P.The present study investigates the combined effect of oxygen enrichment and exhaust gas recirculation (EGR) on the performance and emission characteristics of a cardanol biofuel blend, namely B20M10 (20% cardanol, 70% diesel and 10% methanol by volume). The tests are conducted on a four-stroke single-cylinder diesel engine at different loading conditions. Intake air is enriched by 7% of the atmospheric oxygen concentration and exhaust gas is recirculated by 10, 15 and 20% of the total intake charge. Research results reveal that the oxides of nitrogen (NOx) emission decreases as the percentage of EGR increases from 0 to 20%. The results shows 11.8% lower NOx B20M10 at 7% oxygen enrichment and 20% EGR when compared to B20M10 without oxygen enrichment and 0% EGR. Higher carbon monoxide (CO), unburnt hydrocarbon (HC) and smoke, and lower brake thermal efficiency are obtained for higher EGR percentages. From the studies it can be stated that B20M10 cardanol biofuel blend with 7% intake air oxygen enrichment and 15% EGR shows better reduction in NOx emissions with minimum penalty of performance and other emission characteristics. © 2016 Informa UK Limited, trading as Taylor & Francis Group.Item Effect of exhaust gas recirculation on a CRDI engine fueled with waste plastic oil blend(Elsevier Ltd, 2018) Ayodhya, A.S.; Lamani, V.T.; Bedar, P.; Kumar, G.N.The inevitable rise in the usage of plastic poses a serious threat to the environment owing to their non-biodegradable nature. The lack of proper infrastructure for treating and recycling plastic wastes give rise to the disposal problem. However, the oil synthesized from these waste plastics can be used as an alternative fuel for C.I engines which not only helps to tackle the disposal problem but also aids in recovering precious energy from these wastes. This experimental investigation aims to study the effects of plastic-diesel blend(P30) fuel on the performance, emission and combustion characteristics of a twin cylinder CRDI engine operating at different EGR rates (0%, 10% and 20%). The experimental results showed a slight drop in the engine performance while operating with plastic blend, mainly overall due to its higher viscosity and lower heating value. The vast upsurge of NOX emissions with plastic blend was mitigated by the aid of EGR methodology. Marginal increase in the discharge of regulated emissions like HC, CO and soot were noticed for both plastic blend as well as EGR operations. The experiments were carried out for five different loading conditions varying from 0% to 80% in steps of 20% each and found out that waste plastic-diesel blend can be successfully used as an alternative fuel in diesel vehicles without any prior modifications in the engine. © 2018 Elsevier LtdItem Combustion, performance, and tail pipe emissions of common rail diesel engine fueled with waste plastic oil-diesel blends(American Society of Mechanical Engineers (ASME) infocentral@asme.org, 2018) Lamani, V.T.; Yadav, A.K.; Kumar, G.N.The demand for plastic is eternally growing in urban areas and producing enormous quantity of plastic waste. The management and disposal of plastic waste have become a major concern worldwide. The awareness of waste to energy retrieval is one of the promising modes used for the treatment of the waste plastic. The present investigation evaluates the prospective use of waste plastic oil (WPO) as an alternative fuel for diesel engine. Different blends (WPO0, WPO30, and WPO50) with diesel are prepared on a volume basis and the engine is operated. Experiments are conducted for various injection timings (9 deg, 12 deg, 15 deg, and 18 deg BTDC) and for different exhaust gas recirculation (EGR) rates (0%, 10%, 15%, and 20%) at 100 MPa injection pressure. Combustion, performance, and tail pipe emissions of common rail direct injection (CRDI) engine are studied. The NOx, CO, and Soot emissions for waste plastic oil-diesel blends are found more than neat diesel. To reduce the NOx, EGR is employed, which results in reduction of NOx considerably, whereas other emissions, i.e., CO and Soot, get increased with increase in EGR rates. Soot for WPO-diesel blends is higher because of aromatic compounds present in plastic oils. Brake thermal efficiency (BTE) of blends is found to be higher compared to diesel. © 2018 by ASME.Item Effect of bioethanol–diesel blends, exhaust gas recirculation rate and injection timing on performance, emission and combustion characteristics of a common rail diesel engine(Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2019) Lamani, V.T.; Baliga M, A.U.; Yadav, A.K.; Kumar, G.N.This investigation is focused on the effect of exhaust gas recirculation (EGR) and injection timing on the performance, combustion and exhaust emission characteristics of common rail direct injection (CRDI) engine fueled with bioethanol-blended diesel using computational fluid dynamics (CFD) simulation. Simulation is carried out for various EGR rates (0, 10, 20 and 30%), two different injection timings, and two different bioethanol–diesel blends (10 and 20%) at injection pressure. The equivalence ratio is kept constant in all the cases of bioethanol–diesel blends. The results indicate that the mean CO formation and ignition delay increase, whereas mean NO formation and in-cylinder temperature decrease, with increase in the EGR rate. Further, with an increase in percentage of the bioethanol blends, CO and soot formation decrease as compared to neat diesel. A significant increase in in-cylinder pressure (15%) is found at 14° before top dead centre (BTDC) compared to 9° BTDC, which leads to an increase in indicated thermal efficiency of 4% for neat diesel at 30% EGR. In the present study, maximum indicated thermal efficiency is obtained in the case of 10 and 20% bioethanol–diesel blend, and remains constant for all EGR rates considered in the study. Obtained results are validated with the available literature data and indicate good agreement. © 2017, © 2017 Informa UK Limited, trading as Taylor & Francis Group.Item Effect of fuel injection strategies and EGR on biodiesel blend in a CRDI engine(Elsevier Ltd, 2019) Bhowmick, P.; Jeevanantham, A.K.; Bragadeshwaran, B.; Kasianantham, K.; Arumuga Perumal, D.A.; Viswanathan, V.; Vora, K.C.; Jain, A.Biodiesel appears as a replenishable and sustainable energy source and can be used a direct replacement to petro-diesel without any major transformations in ongoing diesel engines. This work concentrates on production of Calophyllum Inophyllum biodiesel (CIB) and preparing 10% blend (CIB10) sample to investigate the effects of varying the injection strategies and exhaust gas recirculation (EGR) in common-rail direct injection engine. The experimental results shows that 10% of pilot fuel and 90% main injection strategy (B10@P10-M90) is superior among all others injection strategies with respect to pure diesel. B10@P10-M90 fuel injection strategy produces the maximum efficiency of 35.8% and lowest fuel consumption of 0.25 kg/kWh compared to all the injection strategies. The carbon monoxide (CO) and hydrocarbon (HC) emissions are also found to be quite low compared to all the other test samples including pure diesel. However B10@P10-M90 results in higher average oxides of nitrogen (NOx) emission which is 18.9% higher in contrast to conventional diesel at full load condition. With the implementation of 10% and 20% EGR with B10@P10-M90, the average NOx emissions decreased by 14.4% and 27.6% respectively compared to B10@P10-M90 without any EGR without significant loss in the performance of the existing diesel engine. © 2019 Elsevier LtdItem Experimental investigations of a low heat rejection (LHR) engine powered with Mahua oil methyl ester (MOME) with exhaust gas recirculation (EGR)(Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2019) Kulkarni, P.S.; Godiganur, G.; Ramesh, M.R.; Banapurmath Nagaraj, N.R.; Khandal, S.V.Continued effort has been made by several researchers to reduce the dependency on fossil fuels by using suitable alternative and renewable fuels such as biodiesels for energy harvesting and vehicular applications. Alternative fuels can partially or totally replace fossil fuels in diesel engine applications and address tailpipe emissions as well, which lead to global warming. Performance of compression ignition (CI) engines fueled with biodiesel can be further improved with low heat rejection engine facility by suitably utilizing the heat rejected from the engine and thereby improving the thermal efficiency. Present work combustion surfaces of piston, valves and cylinder head were coated with ceramic material, making the engine fully adiabatic, also known as a low heat rejection (LHR) engine. Experiments were conducted on an LHR engine using diesel and Mahua oil methyl ester (MOME) to determine its performance with and without exhaust gas recirculation (EGR). An attempt has been made to compare the performance and emissions characteristics of a CI engine operated on MOME with and without ceramic coating, and the effect of an EGR system developed in-house. EGR was varied from 0 to 20% in steps of 5%. The LHR engine yielded increased brake thermal efficiency (BTE), reduced emissions of smoke, HC[Hydro Carbon] and CO, and increased NOx with MOME when compared to an uncoated engine. As EGR rate increased the BTE and NOx were slightly reduced whereas the HC, CO and smoke were increased. At 10% EGR, 25.96% BTE, 59 HSU smoke, 46 ppm HC, 0.163% volume CO and 1048 ppm NOx were reported. © 2017, © 2017 Informa UK Limited, trading as Taylor & Francis Group.Item Effect of exhaust gas recirculation rate on performance, emission and combustion characteristics of a common-rail diesel engine fuelled with n-butanol–diesel blends(Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2020) Lamani, V.T.; Yadav, A.; Gottekere, K.N.Increasing fears of fossil fuel attenuation and tough emission protocols compel the research community to explore alternative renewable fuels for diesel engines. Butanol is desirable among renewable fuels due to its properties favorable to diesel engines. This study focused on the suitability of exhaust gas recirculation (EGR) and optimum injection timing on the performance, combustion and exhaust emission characteristics of common-rail direct-injection (CRDI) engine fueled with n-butanol-blended diesel using experimental and computational fluid dynamics (CFD) simulation. Various EGR rates and injection timings are considered for different butanol–diesel blends (0, 10, 20 and 30%). Obtained simulation results are validated with experimental data and found to be in good agreement. For all EGR rates and blends, nitrogen oxide (NO) emission is reduced drastically, whereas carbon monoxide (CO) and soot emissions are decreased moderately, with increase in n-butanol–diesel blends. The CO and soot emissions increase with EGR rate due to oxygen deficiency as well. Brake thermal efficiency is reduced by approximately 1% for neat diesel (Bu0) with increase in EGR rates. Soot emission for Bu30 (15 ° Before top dead centre (BTDC) is decreased by 23, 25, 24 and 26% for 0, 10, 20 and 30% EGR rates, respectively, compared to Bu0 (12° BTDC). © 2017, © 2017 Informa UK Limited, trading as Taylor & Francis Group.