Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
64 results
Search Results
Item Nano ZnO-activated carbon composite electrodes for supercapacitors(2010) Muthu, M.S.; Bhat, D.K.; Aggarwal, A.; Prahladh Iyer, S.; Sravani, G.A symmetrical (p/p) supercapacitor has been fabricated by making use of nanostructured zinc oxide (ZnO)-activated carbon (AC) composite electrodes for the first time. The composites have been characterized by field emission scanning electron microscopy (FESEM) and X-ray diffraction analysis (XRD). Electrochemical properties of the prepared nanocomposite electrodes and the supercapacitor have been studied using cyclic voltammetry (CV) and AC impedance spectroscopy in 0.1 M Na2SO4 as electrolyte. The ZnO-AC nanocomposite electrode showed a specific capacitance of 160 F/g for 1:1 composition. The specific capacitance of the electrodes decreased with increase in zinc oxide content. Galvanostatic charge-discharge measurements have been done at various current densities, namely 2, 4, 6 and 7 mA/cm2. It has been found that the cells have excellent electrochemical reversibility and capacitive characteristics in 0.1 M Na2SO4 electrolyte. It has also been observed that the specific capacitance is constant up to 500 cycles at all current densities. © 2010 Elsevier B.V. All rights reserved.Item Microwave synthesized nanostructured TiO 2 -activated carbon composite electrodes for supercapacitor(Elsevier B.V., 2012) Muthu, M.; Bhat, D.K.Electrochemical properties of a supercapacitor based on nanocomposite electrodes of activated carbon with TiO 2 nano particles synthesized by a microwave method have been determined. The TiO 2 /activated carbon nanocomposite electrode with a composition of 1:3 showed a specific capacitance 92 Fg -1 . The specific capacitance of the electrode decreased with increase in titanium dioxide content. The p/p symmetrical supercapacitor fabricated with TiO 2 /activated carbon composite electrodes showed a specific capacitance of 122 Fg -1 . The electrochemical behavior of the neat TiO 2 nanoparticles has also been studied for comparison purpose. The galvanostatic charge-discharge test of the fabricated supercapacitor showed that the device has good coulombic efficiency and cycle life. The specific capacitance of the supercapacitor was stable up to 5000 cycles at current densities of 2, 4, 6 and 7 mA cm -2 . © 2012 Elsevier B.V.Item Magnetron sputtered MoO3/carbon nanotube composite electrodes for electrochemical supercapacitor(Elsevier B.V., 2013) Aravinda, L.S.; Nagaraja, K.K.; Bhat, K.; Badekai Ramachandra, B.Molybdenum oxide (MoO3) has been deposited on multiwalled carbon nanotubes (MWCNTs) using DC reactive magnetron sputtering of molybdenum for supercapacitor applications. The deposits of MoO3 have been developed under different intervals of time. The structure and surface morphology of the deposits have been characterized by means of X-ray diffraction (XRD) analysis and field emission scanning electron microscopy (FESEM). X-ray diffraction peaks of the composite films reveal the formation of crystalline structure of MoO3. The electrochemical performance of the composite films was studied using cyclic voltammetry (CV), galvanostatic charge discharge and electrochemical impedance spectroscopy measurements. The composite film exhibits maximum specific capacitance of 70 F g-1 at a scan rate of 10 mV s-1 in 1 M Na2SO4 electrolyte. The nanocomposite electrode material shows specific capacitance which is almost four fold increase with respect to that of bare MWCNTs. The effect of coating duration on specific capacitance has been studied. The nanocomposite film is found to display good cycleability, even up to 1000 cycles. © 2013 Elsevier Inc. All rights reserved.Item Wire electric discharge machining characteristics of titanium nickel shape memory alloy(Nonferrous Metals Society of China B12 Fuxing Road Beijing 100814, 2014) Manjaiah, M.; Narendranath, S.; Basavarajappa, S.; Gaitonde, V.N.TiNi shape memory alloys (SMAs) have been normally used as the competent elements in large part of the industries due to outstanding properties, such as super elasticity and shape memory effects. However, traditional machining of SMAs is quite complex due to these properties. Hence, the wire electric discharge machining (WEDM) characteristics of TiNi SMA was studied. The experiments were planned as per L27 orthogonal array to minimize the experiments, each experiment was performed under different conditions of pulse duration, pulse off time, servo voltage, flushing pressure and wire speed. A multi-response optimization method using Taguchi design with utility concept has been proposed for simultaneous optimization. The analysis of means (ANOM) and analysis of variance (ANOVA) on signal to noise (S/N) ratio were performed for determining the optimal parameter levels. Taguchi analysis reveals that a combination of 1 ?s pulse duration, 3.8 ?s pulse off time, 40 V servo voltage, 1.8×105 Pa flushing pressure and 8 m/min wire speed is beneficial for simultaneously maximizing the material removal rate (MRR) and minimizing the surface roughness. The optimization results of WEDM of TiNi SMA also indicate that pulse duration significantly affects the material removal rate and surface roughness. The discharged craters, micro cracks and recast layer were observed on the machined surface at large pulse duration.Item Solar exfoliated graphene and its application in supercapacitors and electrochemical H2O2 sensing(Elsevier Ltd, 2015) Moolayadukkam, M.; Huang, N.M.; Nagaraja, H.S.In the present study, graphene nanosheets are synthesized using sunlight irradiation focussed onto graphite oxide. The morphological characteristics of graphene are examined using Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM). Raman spectroscopy and X-ray diffraction (XRD) are used for the structural characterization of the sample. The electrochemical performance is evaluated using cyclic voltammetry (CV), charge-discharge characteristics and impedance spectroscopy. A high specific capacitance value of 223 F g-1 is obtained using cyclic voltammetry. The electrochemical detection of H2O2, a common biological species using solar graphene is demonstrated. The impedance spectroscopy and CV are used to study the electrocatalytic activity of the material. High sensitivity of 64.79 ?A mM-1 cm-2 is reported. © 2015 Elsevier Ltd. All rights reserved.Item Effect of electrode material in wire electro discharge machining characteristics of Ti50Ni50-xCux shape memory alloy(Elsevier Inc. usjcs@elsevier.com, 2015) Manjaiah, M.; Narendranath, S.; Basavarajappa, S.; Gaitonde, V.N.Abstract TiNiCu alloy belongs to new class of shape memory alloy (SMA), which exhibits superior properties like shape memory effect, super elasticity and reversible martensitic transformation phase and thus find broad applications in actuators, micro tools and stents in biomedical components. Even though, SMA demonstrates outstanding property profile, traditional machining of SMAs is fairly complex and hence non-traditional machining like wire electric discharge machining (WEDM) has been performed. Hence, there is a need to investigate the WEDM performance characteristics of shape memory alloys due to excellent property profile and potential applications. In the present investigation, various machining characteristics like material removal rate (MRR), surface roughness, surface topography and metallographic changes have been studied and the influence of wire material on TiNiCu alloy machining characteristics has also been evaluated through ANOVA. Ti50Ni50-xCux=10, 20 was prepared by vacuum arc melting process. The proposed alloy as-cast material exhibits austenite property (B2 phase) and having higher hardness when compared to TiNi alloy. The investigation on WEDM of Ti50Ni50-xCux alloy reveals that the machining parameters such as servo voltage, pulse on time and pulse off time are the most significant parameters affecting MRR as well as surface roughness using both brass and zinc coated brass wires. However, machining with zinc coated brass wire yields reduced surface roughness and better MRR and also produces less surface defects on the machined surface of Ti50Ni50-xCux alloys. © 2015 Elsevier Inc. All rights reserved.Item Effect of acid dopants in biodegradable gel polymer electrolyte and the performance in an electrochemical double layer capacitor(Institute of Physics Publishing custserv@iop.org, 2015) Sudhakar, Y.N.; Muthu, M.; Bhat, D.K.Proton-conducting biodegradable gellan gum gel polymer electrolytes (GPEs) have been prepared using three different dopants, namely ortho-phosphoric (o-H3PO4), sulfuric (H2SO4) and hydrochloric acids (HCl). The GPEs were cross-linked using borax. The polymeric gels were characterized by spectroscopic, thermal, ionic conductivities and dielectric measurements. Proton conductivity was in the range of 5.1 × 10-3 to 3.7 × 10-4 s cm-1 and activation energies were between 0.14 meV and 0.19 meV, at different temperatures. Among the doped acids, the H3PO4 doped GPE exhibited thermal stability at varying temperature. Electrochemical double layer capacitors (EDLCs) were fabricated using activated carbon as electrode material and GPEs. The EDLCs were tested using cyclic voltammetry, ac impedance spectroscopic and galvanostatic charge-discharge techniques. The maximum specific capacitance value was 146 F g-1 at a scan rate of 2 mV s-1. Quite stable values were obtained at a constant current density up to 1000 cycles. © 2015 The Royal Swedish Academy of Sciences.Item Preparation and characterization of phosphoric acid-doped hydroxyethyl cellulose electrolyte for use in supercapacitor(SpringerOpen, 2015) Sudhakar, Y.N.; Muthu, M.; Bhat, D.K.A new borax cross-linked biodegradable solid polymer electrolyte based on hydroxyethyl cellulose and phosphoric acid (H3PO4) was prepared. Characterizations of doped and undoped SPE were done using Fourier transform infrared spectroscopic and electrochemical studies. The ionic conductivity of the films increased with increase in acid concentration and the ionic conductivity obtained at 303 K was 4.1 × 10-3 S cm-1. Furthermore, effects of acid concentration on ionic conductivity and activation energy were discussed. Dielectric studies showed long tail-like feature indicating capacitive nature. A supercapacitor was fabricated and its electrochemical characteristics were studied. The supercapacitor showed a fairly good specific capacitance of 83 F g-1 at 2 mV s-1 and galvanostatic charge-discharge studies showed the mirror-like pattern with 98 % columbic efficiency. Cyclic stability was measured up to 2000 cycles. © 2015 The Author(s).Item Novel Fe-Ni-Graphene composite electrode for hydrogen production(Elsevier Ltd, 2015) Badrayyana, S.; Bhat, D.K.; Shenoy, U.S.; Ullal, Y.; Hegde, A.We have developed a novel, efficient and economical composite electrode for hydrogen production. The electrode has been formed by embedding graphene in the Fe-Ni matrix via room temperature electrodeposition. The obtained active coatings have been tested for their efficiency and performance as electrode surfaces for hydrogen evolution reaction (HER) in 6 M KOH by cyclic voltammetry and chronopotentiometry techniques. The coating obtained at 60 mA cm-2 exhibited approximately 3 times higher activity for hydrogen production than that of binary Fe-Ni alloy. Addition of graphene to electrolyte bath resulted in porous 3D projections of nano-sized spheres of Fe-Ni on the surface of graphene, which effectively increased the electrochemically active surface area. XPS analysis results showed the equal distribution of both Ni metal and NiO active sites on the composite. The addition of graphene favoured the deposition of metallic nickel, which accelerated the rate determining proton discharge reaction. All these factors remarkably enhanced the HER activity of Fe-Ni-Graphene (Fe-Ni-G) composite electrode. The Tafel slope analysis showed that the HER follows Volmer-Tafel mechanism. The structure-property relationship of Fe-Ni-G coating has been discussed by interpreting field emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) analysis results. © 2015 Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.Item Electrolytic Synthesis and Characterization of Electrocatalytic Ni-W Alloy(Springer New York LLC barbara.b.bertram@gsk.com, 2015) Elias, L.; Scott, K.; Hegde, A.Inspired by the more positive (about 0.38 V nobler) discharge potential of hydrogen on Ni-W alloy compared to that on both Ni and W, a Ni-W alloy has been developed electrolytically as an efficient electrode material for water electrolysis. The deposition conditions, for peak performance of the electrodeposits for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in 1.0 M KOH medium have been optimized. Electrocatalytic activity of the coatings, deposited at different current densities (c.d.’s) for water splitting reactions of HER and OER was tested by cyclic voltammetry and chronopotentiometry. It was found that Ni-W alloys deposited, at 4.0 A/dm2 (having about 12.49 wt.% W) and 1.0 A/dm2 (having about 0.95 wt.% W) are good electrode materials as cathode (for HER) and anode (for OER), respectively. A dependency of the electrocatalytic activity for HER and OER with relative amount of Ni and W, in the deposit was found. The variation of electrocatalytic activity with W content showed the existence of a synergism between high-catalytic property of W (due to low hydrogen overvoltage) and Ni (having increased adsorption of OH? ions), for hydrogen (as cathode) and oxygen (as anode) evolution, respectively. Electrocatalytic activities of the coatings, developed at different c.d.’s were explained in the light of their phase structure, surface morphology, and chemical composition, confirmed by XRD, FESEM, and EDX analysis. The effect of c.d. on thickness, hardness, composition, HER, and OER was analyzed, and results were discussed with possible mechanisms. © 2015, ASM International.